HBT100UB
HDMI USB KVM Extender over
Cat5e/Cat6(HDBaseT)
VER 1.0
Thank you for purchasing this product
For optimum performance and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this manual for future
reference.
Surge protection device recommended
This product contains sensitive electrical components that may bedamaged by electrical
spikes, surges, electric shook, lighting strikes, etc. Use of surge protection systems is
highly recommended in order to protect andextend the life of your eauipment.
Table of Contents
1. Introduction.............................................................................................................................
2. Features.....................................................................................................................................
3. Package Contents..................................................................................................................
4. Specifications..........................................................................................................................
5. Operation Controls and Functions..................................................................................
6. IR Cable Pin Assignments...................................................................................................
7. Connection Diagram............................................................................................................
8. Aplication Example...............................................................................................................
Caution:
The extender using UTP cable termination follows the standard of IEEE-568B.
2
2
2
3
4
7
8
11
1/11
1. Introduction
The HDMI USB KVM (Keyboard, Video, Mouse) Extender is a tool which can extend
your HDMI signal over 328fts/100meters to a compatible display. It is designed to
convert HDMI signal to standard HDBaseT signal which can be transmitted by CAT5e/
CAT6/CAT7 cable. It also supports Transfer Bidirectional Infrared control signal and
RS232 control signal. With LAN serving connection and external digital and analog
audio capability that gives users the convenience of additional audio connection. It also
supports the connection of USB host and 2 USB device ports. So you can control the
Source in the Sink side which is 328fts outside, also you can control the Sink in the
Source side which is 328fts outside using the HDMI Extender.
2. Features
☆ Fully compliant with HDMI 1.4, and compatible with HDMI 2.0 (4K2K@60Hz with
YCbCr 4:2:0 ).
☆ HDCP2.2 and DVI compatible.
☆ Supports HDBaseT 2.0 specification over a single CAT5e/6/7 cable up to 100m/328ft.
☆ Supports pass-through of HD audio formats: LPCM2/5.1/7.1 CH, Dolby Digital,
DTS, Dolby TrueHD, DTS-HD Master Audio and more.
☆ POE(Power Over Ethernet)function support, either TX or RX powered 24V@1A,
another don’t need power form the DC jack.
☆ Full HD support: 1080p@60Hz@24/36/48bit/pixels.
☆ Supports USB 2.0 control.
☆ Supports external Bi-Directional SPDIF IN/OUT and available for multichannel audio.
☆ Supports stereo audio with PCM 2CH.
☆ Transfer Bidirectional Infrared control signal together with the HDMI signal.
☆ Transfer Bidirectional RS232 control signal together with the HDMI signal.
☆ Transfer Bidirectional Ethernet signal together with the HDM signal.
3. Package Contents
1.HDMI USB KVM Extender Transmitter --------------------------------------------------- 1PCS
2.HDMI USB KVM Extender Receiver -------------------------------------------------------1PCS
3.Wideband IR Tx -------------------------------------------------------------------------------- 2PCS
4.Wideband IR Rx -------------------------------------------------------------------------------- 2PCS
5.24V/1A DC power adaptor ------------------------------------------------------------------- 1PCS
6.Operation Manual ------------------------------------------------------------------------------ 1PCS
7.Phoenix male jack-------------------------------------------------------------------------------2PCS
8.Mounting ears-------------------------------------------------------------------------------------4PCS
Website: www.seada.co.uk E-mail: sales@seada.co.uk
2/11
4. Specifications
Technical
Technical
Video Bandwidth
Transmitter input
ports
Transmitter output
ports
Receiver input
ports
Receiver output
ports
Power Supply
ESD Protection
Dimensions
Weight
Operating Temperature
Storage Temparature
Relative Humidity
Power Consumption
340MHz[10.2Gbps]
1x HDMI，1×LAN，1×USB-H，1x IR in，
1×Optical(Spdif in)，1×Audio in，1×RS-232
1xIR out, 1xOptical (Spdif out),
1xHDBaseT OUT, 2xUSB-D
1xIR in, 1xOptical (Spdif in),
1xHDBaseT IN, 1xUSB-H
1x HDMI, 1xLAN, 2xUSB, 1xIR out, 1x Audio out,
1xRS232,1xOptical (Spdif out),
DC 24V 1A
Human-body Model：±8kV (Air-gapdischarge) ,
±4kV (Contact discharge)
160(W) X 97 (D) X 28 (H)
450g x 2
0°C ~ 40°C / 32°F ~ 104°F
-20°C ~ 60°C / -4°F ~ 140°F
20~90% RH (non-condensing)
12W
Website: www.seada.co.uk E-mail: sales@seada.co.uk
3/11
5. Operation Controls and Functions
☆ Transmitter Front Panel
AUDIO IN
2
3 4
3
Number
1
2 IR IN
3
4
5
6
7
8
Name
Power LED illuminates when power has been supplied to the unit
Link LED
HDCP LED
FW LED
IR OUT
RS232 TX/RX
AUDIO IN
USB-D
USB-H
USB-H/USB-D
SELECT
4
Function description
The connection status indicating lamp.
Illuminate: The Transmitter and Receiver is good
connections.
Flashing: The Transmitter and Receiver is poor
connections.
Dark: The Transmitter and Receiver is no connections
The HDCP status indicating lamp.
Illuminate: The HDMI signal with HDCP.
Flashing: The HDMI signal without HDCP.
Dark: No HDMI signal.
Light is flashing on behalf of the unit work normally
Chanel 1 IR Receiver. Connect with Wideband IR Rx
Chanel 2 IR Transmitter. Connect with Wideband IR Tx
Connect to a PC or Laptop with 3-pin Relay cable for
the transmission of RS-232 commands.
Connect to a PC or Laptop stereo output port via
3.5mm audio cable.
Connect to USB peripheral devices such as printer,
keyboard, mouse, flash driver or …etc.
Connect from PC or Laptop for data transmit to or
control from the Receiver’s USB-D slots.
Select USB host or USB device.
Note: If the unit work to change the state, required
again to power
6
5
7 81
Website: www.seada.co.uk E-mail: sales@seada.co.uk
4/11
☆ Transmitter Rear Panel
1
Number
2
Name
1
UPDATE
HDBaseT OUT
2
HDMI IN
3
SPDIF IN
4
(Optical in)
SPDIF OUT
5
(Optical out)
6
LAN
DC IN Plug the 24V DC power supply into the unit
7
3
4
3
4
Reserved for manufacturer use only
Standard HDBaseT signal output port. Connect
HDBaseT receiver with a Cat5e/6/7 cable.
This slot is where you connect the HDMI source
Connect to audio source equipment such as DVD or
Blu-ray player for audio signal sending to Receiver’s
SPDIF OUT(Optical out).
Connect to speaker with coaxial input for audio signal
output from Receiver’s SPDIF IN(Optical in)
This slot provide Internet signal from receiver or to
receiver
Function description
5
6
7
Website: www.seada.co.uk E-mail: sales@seada.co.uk
5/11
☆ Receiver Front Panel
2
3 4
3
Number
1
2 IR IN
3
4
5
6
7
8
Name
Power LED illuminates when power has been supplied to the unit
Link LED
HDCP LED
FW LED
IR OUT
RS232 TX/RX
AUDIO OUT
USB-D
USB-H
USB-H/USB-D
SELECT
4
Function description
The connection status indicating lamp.
Illuminate: The Transmitter and Receiver is good
connections.
Flashing: The Transmitter and Receiver is poor
connections.
Dark: The Transmitter and Receiver is no connections
The HDCP status indicating lamp.
Illuminate: The HDMI signal with HDCP.
Flashing: The HDMI signal without HDCP.
Dark: No HDMI signal.
Light is flashing on behalf of the unit work normally
Chanel 1 IR Receiver. Connect with Wideband IR Rx
Chanel 2 IR Transmitter. Connect with Wideband IR Tx
Connect to a PC or Laptop with 3-pin Relay cable for
the transmission of RS-232 commands.
Connect to speaker via 3.5mm audio cable
Connect to USB peripheral devices such as printer,
keyboard, mouse, flash driver or …etc.
Connect from PC or Laptop for data transmit to or
control from the Receiver’s USB-D slots.
Select USB host or USB device.
Note: If the unit work to change the state, required
again to power supply.
6
5
7 81
Website: www.seada.co.uk E-mail: sales@seada.co.uk
6/11
☆ Receiver Rear Panel
HDBaseT IN
1
Number
1
2
3
4
5
6
7
2
Name
UPDATE
HDBaseT IN
HDMI OUT
SPDIF IN
(Optical in)
SPDIF OUT
(Optical out)
LAN
DC IN Plug the 24V DC power supply into the unit
HDMI OUT
3
3
4
Reserved for manufacturer use only
Standard HDBaseT signal output port. Connect
HDBaseT Transmitter with a Cat5e/6/7 cable
This slot is where you connect the a HDMI equipped
TV/monitor.
Connect to audio source equipment such as DVD or
Blu-ray player for audio signal sending to Receiver’s
SPDIF OUT(Optical out).
Connect to speaker with coaxial input for audio signal
output from Receiver’s SPDIF IN(Optical in)
This slot provide Internet signal from receiver or to
receiver
6. IR Cable Pin Assignments
5
4
Function description
6
7
Website: www.seada.co.uk E-mail: sales@seada.co.uk
7/11
7. Connection Diagram
※ Picture 1
POE(Power Over Ethernet) Application Example
CAT5e /6/7
CAT5e /6/7
※ Picture 2
Bidirectional Infrared control Application Example
HDM I Cable
RX
TX 2
Rx1
TV
TV Remo te
UTP Ca ble
TX
DVD Rem ote
Rx2
8/11
HDM I Cable
TX 1
Website: www.seada.co.uk E-mail: sales@seada.co.uk
※ Picture 3
Bidirectional RS232 control Application Example
※ Picture 4
Bidirectional Ethernet signal Application Example
Website: www.seada.co.uk E-mail: sales@seada.co.uk
9/11
※ Picture 5
USB control Application Example
HDM I Cable
USB C able
TX
CAT 5e/6/ 7
RX
USB C able
USB C able
Mouse
PC
Keyboard
RX
USB C able
Notebook
Print er
USB C able
TX
CAT 5e/6/ 7
※ Picture 6
Digital Audio bidirectional transmission Application Example
DVD
Amp lifier
SPD IF Cabl e
SPD IF Cabl e
SPD IF Cabl e
TX
CAT5e /6/7
CAT5e /6/7
TX
RX
RX
SPD IF Cabl e
Amp lifier
TV
DVD
Website: www.seada.co.uk E-mail: sales@seada.co.uk
10/11
8. Application Example
Website: www.seada.co.uk E-mail: sales@seada.co.uk
11/11
Loading...