APPENDIX A Specifications.............................................................. 23
Page 2 of 25
Wireless Network Adapter User manual
Chapter 1 Introduction
1.1 Welcome
The Wireless Network Adapter is a powerful 32-bit Cardbus/PCI Adapter that
installs quickly and easily into PCs. The Adapter can be used in Ad-Hoc mode to
connect directly with other cards for peer-to-peer file sharing or in
Infrastructure mode to connect with a wireless access point or router for access
to the Internet in your office or home network.
The Wireless Cardbus/PCI/USB Adapter connects you with 802.11g networks at
up to an incredible 54Mbps! And for added versatility, it can also interoperate
with all the up to 11Mbps 802.11b products found in homes, businesses, and
public wireless hotspots around the country. And in either mode, your wireless
communications are protected by industrial-strength WPA, so your data stays
secure.
1.2 About This Guide
This User Manual contains information on how to install and configure your
Wireless Adapter to get your network started accessing the Internet. It will
guide you through the correct configuration steps to get your device up and
running.
Note and Caution in this manual are highlighted with graphics as below to
indicate important information.
Contains related information corresponds to a topic.
Necessary steps, actions or messages should not be ignored.
1.3 Copyright statement
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise without the prior writing of the
publisher.
Page 3 of 25
Wireless Network Adapter User manual
1.4 Contents of Package
z Wireless network Cardbus/PCI/USB adapter
z Manual, Drivers and Utility on CD
z Quick Installation Guide
If any of the above items are missing, please contact your reseller.
1.5 Before you begin
You must have at least the following:
z A laptop computer/desktop PC with an available 32-bit Cardbus/PCI slot
z At least a 300MHz processor and 32MB of memory
z Windows 98SE, ME, 2000, XP
z A CD-ROM Drive
z Cardbus/PCI/USB controller properly installed and working in the laptop
computer
z A 802.11g or 802.11b Access Point (for infrastructure Mode) or another
802.11g or 802.11b wireless adapter (for Ad-Hoc; Peer-to-Peer networking
mode.)
Chapter 2 Designing Your Wireless Network
The wireless Cardbus/PCI/USB Adapter supports up to 54 Mbps connections.
This card is fully compliant with the specifications defined in IEEE802.11g
standard. It is designed to complement PCI Local Bus computers and supports
Windows 98SE/Me/2000/XP.
2.1 Cardbus adapter
Figure 2-1
Page 4 of 25
Wireless Network Adapter User manual
The two status LED indicators of the Cardbus wireless adapter are described in
the following.
z PWR ON (Green): Indicates the Adapter is ready
z Lnk/Act ON (Green): Indicates a valid connection
z Lnk/Act Flashing: Indicates the Adapter is transmitting or receiving data.
2.2 PCI adapter
Figure 2-2
The status LED indicators of the PCI wireless adapter are described in the
following.
z Lnk/Act ON (Green): Indicates a valid connection
z Lnk/Act Flashing: Indicates the Adapter is transmitting or receiving data.
2.3 USB adapter
The status LED indicators of the USB wireless adapter are described in the
following.
z Lnk/Act ON (Green): Indicates a valid connection
z Lnk/Act Flashing: Indicates the Adapter is transmitting or receiving data.
Figure 2-3
Page 5 of 25
Wireless Network Adapter User manual
Chapter 3 Install Wireless Adapter
3.1 Install Driver and Utility
z Insert the Driver and Utility CD-ROM into the CD-ROM driver.
z The Wizard should run automatically, and Figure 2-1 should appear. If it
dose not, click the Start button and choose Run. In the field that appears,
enter D:\autorun.exe (if ‘’D’’ is the letter of your CD-ROM drive).
Figure 2-1
z Click Install Driver & Utility on the Wireless Client Configuration Utility
screen.
Page 6 of 25
Wireless Network Adapter User manual
Figure 2-2
zFollow the Install Shield Wiza rd st eps , and clic k Finish when done.
Figure 2-3
z Now turn off your PC or notebook
Page 7 of 25
Wireless Network Adapter User manual
3.2 Install Adapter
3.2.1 Cardbus Adapter
z Power on your notebook, let the operating system boot up completely, and
log in as needed.
zHold the adapter with the LOGO facing up and insert it into a Cardbus slot.
Figure 3-1
zIf the Found New Hardware Wizard displays, choose Install the software
automatically (Recommended), and click Next button. The driver will
be installed automatically.
Page 8 of 25
Loading...
+ 17 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.