801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •
www.sdcsecurity.com • E-mail: serv ice@sdcsecurity.com
1291ADMR
INSTALLATION INSTRUCTIONS/TEMPLATE
MECHANICAL RELEASE
ALUMINUM FRAME MOUNT CONFIGURATION
1.755
O1.150
.865
.750
(8X) TAP TABS
FOR #10-32
CYLINDER NOT
INCLUDED
11.605
10.500
1.500
NOTE: TEMPLATE DIMENSIONS ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
TECHNICAL DATA (FOR STANDARD UNIT)
FACE PLATE: 10-1/2" x 1-1/2" X 1/8"
STRIKE: 4" x 1-1/2” x 1/8”
ID REQUIREMENTS: 10-1/2” x 1-1/2” x 1-1/2”
BOLT: 5/8” DIA. STAINLESS STEEL
BOLT THROW: 5/8”
P:\INSTALLATION INST\Electric Bolt Locks\Temp-1291A\Temp-1291ADMR.vsd REV A 09-17 Page 1
(2X) TAP FOR #10-32
4.00
C
OF BOLT
L
Door Preparation
1.51
.750
3.25
4.00
1.50
.125
C
OF DOOR
L
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email engineer@sdcsecurity.com
HOLLOW METAL FRAME MOUNT CONFIGURATION
1.755
O1.150
.865
.750
(8X) TAP TABS
FOR #10-32
CYLINDER NOT
INCLUDED
11.605
10.500
1.500
(2X) TAP FOR #10-32
NOTE: TEMPLATE DIMENSIONS ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
TECHNICAL DATA (FOR STANDARD UNIT)
FACE PLATE: 10-1/2" x 1-1/2" X 1/8"
STRIKE: 4" x 1-1/2” x 1/8”
ID REQUIREMENTS: 10-1/2” x 1-1/2” x 1-1/2”
BOLT: 5/8” DIA. STAINLESS STEEL
BOLT THROW: 5/8”
C
OF BOLT
L
4.00
1.50
1.51
.125
.750
C
OF DOOR
L
3.25
Door Preparation
4.00
P:\INSTALLATION INST\Electric Bolt Locks\Temp-1291A\Temp-1291ADMR.vsd REV A 09-17 Page 2
DOOR MOUNT CONFIGURATION
1.755
O1.150
.865
.750
(8X) TAP TABS
FOR #10-32
CYLINDER NOT
INCLUDED
11.605
10.500
Frame Preparation
1.500
NOTE: TEMPLATE DIMENSIONS ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
TECHNICAL DATA (FOR STANDARD UNIT)
FACE PLATE: 10-1/2" x 1-1/2" X 1/8"
STRIKE: 4" x 1-1/2” x 1/8”
ID REQUIREMENTS: 10-1/2” x 1-1/2” x 1-1/2”
BOLT: 5/8” DIA. STAINLESS STEEL
BOLT THROW: 5/8”
C
L
4.00
OF
BOLT
1.50
.125
4.00
1.51
.750
3.25
OF
C
L
STRIKE
(2X) TAP
FOR
#10-32
P:\INSTALLATION INST\Electric Bolt Locks\Temp-1291A\Temp-1291ADMR.vsd REV A 09-17 Page 3
INSTRUCTIONS FOR REVERSING THE CYLINDER
Cylinder
Locking
Set Screw
Sliding Link Block
Remove the Cylinder locking set screw, and screw the
Cylinder out of the Mounting Block.
Remove the four screws securing the Mounting Block
and the Sliding Link Block.
Mounting Block
Reverse the components and
re-install as shown.
P:\INSTALLATION INST\Electric Bolt Locks\Temp-1291A\Temp-1291ADMR.vsd REV A 09-17 Page 4
Make sure the sliding Link Block is aligned properly
LOCK WIRING
Select 24VDC OR 12VDC Configuration, and use provided pigtail connector:
24VDC SOLENOID
CONFIGURATION
FROM
LOCK
(PRE-
WIRED)
PIGTAIL
CONNECTOR
12VDC SOLENOID
CONFIGURATION
FROM
LOCK
(PRE-
WIRED)
PIGTAIL
CONNECTOR
RED (+)
BLU
BLK
WHITE (-)
(+)
RED
BLK
BLU
WHITE (-)
ORANGE
ORANGE
Access Control or
Push Button (N/O)
N/C
N/O
Access Control or
Push Button (N/O)
N/C
N/O
COM
COM
24VDC +/-10%
(+)
POWER
(-)
INPUT
ELECTRICAL DATA:
Dual Voltage Solenoid
12VDC@ .9 mA (max.)
24VDC@ .45 mA (max.)
Continuous Duty
12VDC +/-10%
(+)
POWER
(-)
INPUT
OPTIONAL BOLT POSITION SENSOR (BPS-MAGNETIC)
B Indicates bolt locked or unlocked 5 Watt
OPTIONAL DOOR POSITION SWITCH (DPS-MECHANICAL)
D Indicates door opened or closed 4A @ 30VDC (Resistive)
N/O
YELLOW / RED
WHITE / BLACK
ORANGE / RED
DPS
*When both options are ordered the Common is shared
P:\INSTALLATION INST\Electric Bolt Locks\Temp-1291A\Temp-1291ADMR.vsd REV A 09-17 Page 5
BPS
DPS / BPS CONFIGURATION
=
=
COM
N/C
=
YELLOW / BLACK
WHITE / BLACK
ORANGE / BLACK
DPS polarity shown with door closed
N/O
=
COM
=
=
BPS polarity shown with bolt retracted
N/C
Loading...