Scytek electronic G5.2W SERIES,A4.2W,A1.2W,G2.2W,A1.1 SERIES Product Manual
G5.2W, G2.2W
A4.2W, A1.2W
A1.1
SERIES
VEHICLE SECURITY SYSTEM
WITH REMOTE START
PRODUCT MANUAL
Limited Lifetime Warranty
This vehicle security system is warranted to the original purchaser, to be free from defects in
material and workmanship. The manufacturer will repair or replace at its option, and free of
charge for the first twelve (12) months, any part that proves defective in material or workmanship
under normal installation, use, and service, provided the product is returned to the manufacturer
freight prepaid. After the first 12 month warranty period there will be a maximum service charge
of $25.00 per calendar year (if required) for repair and/or replacement of any defective parts.
A copy of the original purchase and installation receipt must accompany any products
returned for warranty service. Warranty is limited to defective parts and/or replacement parts
only and excludes any incidental, and consequential damages connected therewith.
The manufacturer of this theft deterrent system makes no warranty against the theft of the vehicle
or its contents. This warranty is not to be construed as an insurance policy against loss.
WARRANTY OF INSTALLATION LABOR, REMOVAL AND RE-INSTALLATION CHARGES ARE
NOT THE RESPONSIBILITY OF THE MANUFACTURER.
Note: This Warranty is voided if the product was not installed by an
Authorized ScyTek Dealer.
1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1
2. Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Adding/Replacing Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Two Car Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
2-way LCD Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Adding/Replacing 2-way Transmitters, Programable features and descriptions. . . . . . .Page 4-8
LCD Transmitter Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
3. System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Remote Arming*/Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Remote Disarming*/Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Tamper Alert* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Silent Arming*/Locking -Disarming*/Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Passive Arming* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Emergency Override* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Optional Coded Emergency Override* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Automatic Rearming* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
Valet Mode/ Driver Calling Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
4. Remote Start Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
Remote Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
Quick Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
Automatic Start Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
Turbo Timer Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
Manual Transmission Remote Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15
5. Extended Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
Ignition Door Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
Ignition Door Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
Dome Light Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
Auxiliary Function Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
Disarm with Auxiliary Function* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
Remote Sensor Disable* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
6. System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 17
Mounting the Control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18
Mounting the Siren* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18
Mounting the Shock Sensor* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18
7. System Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 19
6-Pin Starter Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 19
20-Pin Main Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 19
Plug-in Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 20
8. Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 21
Jumper Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 21
9. System Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Entering System Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Default Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Programmable System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
10. Relay Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 26
11. Door Lock Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 27
12. Two Stage Door Lock Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 28
13. Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 30
14. System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 31
15. Shock Sensor Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 43
16. Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Page
Table of Contents
2WC-KIT
Two Way Pager upgrade kit
Easy Plug and Play upgrade to a complete two way system.
Increases range
MobiLink 100
Smart phone upgrade
Easy Plug and Play upgrade through the system- Antenna port
2 Way confirmation
Arm/Disarm
Remote Start On/Off
Trunk Release
Alert Notification
MobiLink GPS
GPS upgrade
Works with MobiLink 100
Easy Plug and Play GPS Tracking upgrade.
Upgrade Options
G5, A4 Series is a
Combination Vehicle Security and Remote Starting System
, G2, A1 Series is
a Remote Starting with keyless entry. With proper installation this system will provide superior protection
and performance for many years to come.
The Galaxy’s G5/G2 Series built-in remote starter is designed to offer maximum convenience by remote
starting your vehicle’s engine, turning on the heater/air conditioner, and then running for a pre-determined
time to provide a comfortable environment once you enter your vehicle.
To ensure the safety and security of the system while it is remote started, the G5/G2 Series employs several
safeguards. In the event the alarm is triggered while the engine is remotely running, the remote start will
immediately shutdown to prevent unauthorized users from attempting to drive the vehicle. The system is
equipped with a hood pin input to prevent access to the engine compartment while the vehicle is remotely
running. The Valet Mode prevents the remote start feature from operating in the event the vehicle is to be
serviced. Finally, the brake pedal also acts as a safety by shutting down the remote start when pressed.
System Contents:
• Main Unit
• One 5-Button 2-Way LCD Remote and One 1-Way 5-Button Remote Transmitter
• Two 5-Button Random Code Remote Transmitters (
RS & SP models
)
• High Output 6-tone Siren with G5, A4
• Dual Stage Shock Sensor with G5, A4
• Status LED/ Coded Emergency Override/ Valet Switch/ Call button built into the antenna (See Page 32)
Options and Convenience Features
**
This ScyTek system includes several optional inputs and outputs allowing the creation of a completely
personalized security and convenience system by offering many optional features such as:
Mobilink - Operate your system using Smart Phone.
**May require additional parts and/or labor, see store for details.
· Second Car Operation
· Keyless Entry
· Two Stage Door Unlocking
· Starter Defeat
· Horn Honk
· Illuminated Entry
· Turbo Timer
· Remote Window Control
· Power Trunk / Hatch Release
· Glass Breakage Sensor
· Radar Sensor
· Remote Head Lamp Control
· Back-up Battery Siren
About Your System
Some of the features described in this manual may require additional parts and/or labor, and may not be
included as part of the standard installation of this unit. Additionally, many features of these systems
have selectable options that must be activated or programmed during the system’s installation. These
items will be identified in the following sections. Please discuss these features and any questions you
may have regarding the installation of this product with Your Authorized Dealer.
G5.2W, G2.2W, A4.2W, A1.2W - Page 1
Standard Remote Transmitter Description
Button 1
Arms and Locks the system and when held for 5 seconds, activates the system’s Panic feature.
Button 1 also locks the doors when the system is in Valet Mode.
Button 2
Disarms and Unlocks the system. Pressing Button 2 again operates the Passenger Unlock feature
(if installed).
Button
2 also unlocks the doors when the system is in Valet Mode.
Button 3
Activates the Auxiliary 1 output. This output will remain on for as long as the button is pressed.
Button 4
Activates the Remote Start feature.
Button 5
is the Page Shift button. Each time the Shift Button is pressed, the LED on the transmitter will
illuminate and the transmitter functions will shift to the next page, allowing access to another set of
features. Once shifted to another page (there are 4 pages total), the transmitter will remain on that page
for 10 seconds or until a button is pressed, then it will return to page 1. Under normal operation, only
pages 1 and 2 are used. Pages 3 and 4 are usually used for Two Car Operation (see page 3).
Shift then Button 1
Arms/Locks the system silently.
Shift then Button 2
Disarms/Unlocks the system silently.
Shift then Button 3
Activates the Auxiliary 2 output. This output will remain on for as long as the button
is pressed.
Shift then Button 4
Activates the Auxiliary 3/Factory rearm output.
Remote Transmitters
Page 2 - G5.2W, G2.2W, A4.2W, A1.2W
Button 1 Button 2
Button 5
LED
Button 3
Button 4
Button 1 Button 2
Button 5
LED
Button 3
Button 4
G Series Remote
A Series Remote Remote
G5.2W, G2.2W, A4.2W, A1.2W - Page 3
Program transmitter(s):
1. Turn on the ignition key On, Off, 4 times and then back On on fifth time.
· The siren will chirp 5 times.
2. Press and hold the Override switch for 5 seconds.
· The siren will chirp 5 times.
· The LED will illuminate.
3. Press Button on the first transmitter.
· The siren will chirp once.
4. Repeat step 3 for each transmitter (up to 4).
5. Turn off the ignition key.
Note:
programming single button transmitter will set the system into a single button mode
operation mode
Remote Transmitter Operation Description
Lock: press and release the button momentarily once - doors will lock within 2 seconds.
Unlock: press and release the button twice within 2 seconds - doors will unlock on the second
button press.
Remote Start/Stop: press and hold the button for 3 seconds the system will remote start/stop.
System Programming
To enter System Programming:
1. Turn on ignition.
2. Within 5 seconds, press the valet switch 5 times.
· The siren will provide three chirps, indicating that you have entered Programming.
3. Press the valet switch the number times equal to the System Option you want to change.
· The siren will chirp each time the valet switch is pressed.
4. Within 5 seconds, press the transmitter button once
. This siren will chirp
Press the valet switch the number times equal to the desired operating system option.
· The siren will chirp to indicate the coresponding setting.
1 chirp = Column 1
2 chirps = Column 2
3 chirps = Column 3
5. When finished, turn off the ignition to save the changes.
One Button Remote Transmitter
A1.1 Series Remote
Page 4 - G5.2W, G2.2W, A4.2W, A1.2W
Adding/Replacing Standard Remote Transmitters
To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired
transmitters ready and follow the steps below.
Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored
transmitter will be erased if it is not programed within the following sequence
To program the transmitter(s):
1. Turn the ignition key On, Off, On, Off, and back On. (Key On 3 times)
· 3 seconds later The siren/horn will chirp/honk 3 times.
2. Press and hold the Override switch for 5 seconds.
· The siren/horn will chirp/honk 5 times.
· The LED will illuminate.
3. Press Button 1 on the first transmitter.
· The siren/horn will chirp/honk once.
4. Repeat step 3 for each transmitter (up to 4).
5. Turn off the ignition key.
Two Car Operation
If two vehicles are equipped with the G5/G2 Series systems, for convenience both can be operated using
the same remote transmitter. If all four transmitters are to be used with both cars, program transmitters
A and B into the first vehicle in the manner described above. Program transmitters C and D by pressing
the Shift button twice before performing steps 3 and 4 above.
When finished programming the first vehicle, program transmitters C and D into the second vehicle as
normal, then program transmitters A and B by pressing the Shift button twice before performing step 3.
When programmed in this manner, the driver of the first car can also operate the second vehicle by pressing
the Shift button twice and the desired function button.
Battery Replacement
The
T5
Remote Transmitter uses two 3 volt lithium batteries (type CR2016)
Depending on the amount of use, the batteries may last up to six months or more before they
need replacement.
In order to change the battery, first remove the screw from the back of the transmitter and separate the
top and bottom halves of the case. While replacing the battery make sure that the positive and negative
terminals are positioned correctly, then carefully reassemble the transmitter case.
G5.2W, G2.2W, A4.2W, A1.2WP - Page 5
2-way LCD Remote Transmitter Description
Page 1
Button 1
Arms and Locks the system and when held for 3 seconds, activates the system’s Panic feature.
Button 1 also locks the doors when the system is in Valet Mode.
Button 2
Disarms and Unlocks the system. Pressing Button 2 again operates the Passenger Unlock feature
(
if installed
).
Button
2 also unlocks the doors when the system is in Valet Mode.
Button 3
Activates the Auxiliary 1 output normally used for trunk release (
note trunk icon on button
).
Button 4
Activates the Remote Start feature.
Button 5
is the Confirmation, Programming and the Page Shift button. Quickly pressing button 5 will activate
the Page 2 function. Pressing button 5 for 2 seconds activates the system’s confirmation feature which will
then display the current status of the system (
armed, disarmed, engine running, etc
.).
Page 2
Button 1
Silently Arms/Locks the system.
Button 2
Silently Disarms/Unlocks the system.
Button 3
Activates the Auxiliary 2 output.
Button 4
Aux 3 or Factory Rearm output.
Button 5
Not Implemented.
Page 3 & 4 are used as Page 1 & 2 for second car operation
LCD Transmitter Battery Replacement
Your Pager Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time.
Depending on the amount of use, the battery may last up to 3 months before it needs replacement. When
the battery needs replacing, the system’s operating range will decrease, the LCD display will show only one
of three bars in the battery icon, or the display and sounds may suddenly stop and start as the battery
voltage drops below minimum.
In order to change the battery, first slide the battery door locking pin to the side. Carefully slide the battery
cover downward until it is free. While replacing the battery make sure that the positive and negative
terminals are positioned correctly, then carefully reassemble the transmitter case.
Button 1 Button 2
Button 3
Button 4
Button 5
Page 6 - G5.2W, G2.2W, A4.2W, A1.2W
Setting The Time
The LCD display is equipped with a 12-hour clock
Set the time:
1. Press and hold Buttons 2 and 3 for three seconds.
· The remote will beep two times and three bars will be shown indicating time set mode is entered.
2. Press and release Button 2 until the correct hour is displayed. (hold button to scroll).
3. Press and release Button 3 until the desired minute is displayed. (hold button to scroll).
4. When the desired time is displayed, press Button 5 to store.
· The remote will beep 3 times to indicate the time has been set.
Setting the control unit internal Auto Daily Start time
The Autostart function is set to a time of a day. if enabled will stay enabled until disabled.
Set the unit Autostart clock function:
1. Press and hold Buttons 2 and 3 until the remote beeps two times.
·”Daily Start” icon will turn ON . ( A ST)
2. Press Button 2 until the desired hour is displayed.
3. Press Button 3 until the desired minute is displayed. The button may be held down to scroll faster.
4. When the desired time is displayed, press Button 1 to send to the daily start time to the control
unit.
· The remote will send and receive confirmation, the responce will display the daily start time
set in the unit.
Setting the pager Auto Daily Start Function
( transmitter must be within 1500ft to
reliably start)
The Daily Start Function provides a timer that allows the vehicle to automatically remote start at a preset
time of day , everyday until the feature is turned off.
Set the pager Autostart clock function:
1. Press and hold Buttons 2 and 3 until the remote beeps four times.
”Alarm On ” icon wil turn ON .
2. Press Button 2 until the desired hour is displayed.
3. Press Button 3 until the desired minute is displayed. The button may be held down to scroll faster.
4. When the desired time is displayed;
press Button 5 to turn ON the daily pager start time, to turn off this feature, repeat steps 1 to 4
than press button one on the remote.
press Button 1 to turn OFF the daily start time
G5.2W, G2.2W, A4.2W, A1.2W - Page 7
Automatic Cold Start Temperature Setting
(
2 step procedure, for second step see page 7 under “C st”
)
The Automatic Cold Start setting sets the temperature threshold. If automatic start is set to cold temperature setting,the
starter will activate every 2 or 4 hours if the temperature drops bellow the set value. (LED will flash slow in this mode)
1. Press and hold Buttons 2 and 3 until the remote beeps five times.
· “cold” is shown indicating automatic cold start temperature set mode is entered.
2. Press Button 2 to increase the temerature.
3. Press Button 3 to decrease the temperature.
4. When the desired temperature is displayed, press Button 1 to store the value.
· The remote will display the temperature and beep 3 times then 4 times to indicate the set temperature.
Automatic Hot Start Temperature Setting
(
2 step procedure, for second step see page 7 under “H st”
)
The Automatic Hot Start setting sets the temperature threshold. If automatic start is set to hot temperature setting, the
starter will activate every 2 or 4 hours if the temperature rises above the set value. ( LED will flash slow in this mode)
1. Press and hold Buttons 2 and 3 until the remote beeps six times.
· “hot” is shown indicating automatic hot start temperature set mode is entered.
2. Press Button 2 to increase the temerature.
3. Press Button 3 to decrease the temperature.
4. When the desired temperature is displayed, press Button 1 to store the value.
· The remote will display the set temperature and beep 3 times then 4 times to indicate the set temperature.
Power Save Mode
Power save mode disables automatic pager operations, alarm and starter status must be checked manually using button
5 for confirmation.
1. Press and hold Buttons 2 and 3 until the remote beeps six times.
· “PS” is shown indicating Power Save set/reset mode is entered.
2. Press Button 1 to tougle Power Save On/Off.
· The remote will display On or Off indicating the current status of the pager.
Pager power save mode status is indicated bellow
LCD Backlight
Transmitter Button 5 is used for confirmation, transmitter programming, as well as activation of the LCD
backlighting for use in the dark. Press and release button 5 momentarily to activate the LCD backlight.
System Confirmation
The 2-way transmitter's confirmation feature allows the current vehicle status to be displayed at any time.
To display system status:
1. Press and hold Button 5 until the display shows CON.
· The transmitter will beep once.
2. Release Button 5.
· The transmitter will beep once.
· The LCD panel will display the current system status.
Programmable Functions using the LCD Transmitter
Pressing and holding transmitter button 5 will scroll through several transmitter programmable options -
DEG, AUTO, SPCL, SSCL, C St, H St, A St, Snd .
DEG Check the temperature inside the vehicle
1. Press and hold Button 5 until the display shows DEG
·The transmitter will beep twice.
2. Release Button 5.
· The transmitter will beep four times.
· The LCD panel will display the temperature inside the vehicle
Normal
Mode
Power Save
Mode
Page 8 - G5.2W, G2.2W, A4.2W, A1.2W
AUTO display starter autostart enabled features.
1. Press and hold Button 5 until the display shows AUTO.
·The transmitter will beep three times.
2. Release Button 5.
· The LCD panel will display what starter auto start features are enabled.
SPCL Program the pager time of a day clock from the internal Remote Starter clock, the remoter starter
sends its time to the pager.
1. Press and hold Button 5 until the display shows SPCL.
·The transmitter will beep four times.
2. Release Button 5.
· The pager will display the new time.
SSCL Program the remote starter time of a day clock from the pagerS
1. Press and hold Button 5 until the display shows SPCL.
·The transmitter will beep five times.
2. Release Button 5.
· The pager will display confirmation that the starter clock is sync.
C St Auto Start Cold Temperature Activation Mode.
1. Press and hold Button 5 until the display shows C St.
· The transmitter will beep 6 times.
2. Release Button 5.
· The transmitter will beep once.
· The LCD panel will show Auto Start Cold Temperature setting.
3. Press and hold Button 5 until the display shows CON.
4. Release Button 5.
· The transmitter will beep once.
· The LCD panel will show "ON" indicating that Auto Start Cold Temperature Activation
Mode is enabled.
H St Auto Start Hot Temperature Activation Mode.
1. Press and hold Button 5 until the display shows H St.
· The transmitter will beep 7 times.
2. Release Button 5.
· The transmitter will beep once.
· The LCD panel will show Auto Start Hot Temperature setting.
3. Press and hold Button 5 until the display shows CON.
4. Release Button 5.
· The transmitter will beep once.
· The LCD panel will show "ON" indicating that Auto Start Hot Temperature Activation
Mode is enabled
A St Auto Start Daily Activation Mode.
1. Press and hold Button 5 until the display shows A St.
· The transmitter will beep 8 times.
2. Release Button 5.
· The transmitter will beep once.
· The LCD panel will show Daily Auto Start time setting.
3. Press and hold Button 5 until the display shows CON.
4. Release Button 5.
· The transmitter will beep once.
· The LCD panel will show "ON" indicating that Daily Auto Start Activation
Mode is enabled
SND sound function selects the transmitter's confirmation mode - Tone or Vibration mode.
Set the transmitter confirmation tones ON or OFF:
1. Press and hold Button 5 until the display shows SND.
· The transmitter will beep 9 times.
2. Release Button 5.
· The transmitter will beep once.
· The LCD transmitter will beep 5 times and display “on” if the sounds are enabled or vibrate and
display "off" for the Remote to vibrate.
Loading...