Scytek electronic 3000Plus User Manual

33000000PPLLUUSS SSEERRIIEESS

VEHICLE SECURITY SYSTEM

PRODUCT MANUAL

Table oof CContents

1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1

2. Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2

3. System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4

4. Extended Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8

5. System Installation Page 11

6. System Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13

7. Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15

8. System Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16

12. Door Lock Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 20

13. Two Stage Door Lock Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 21

14. Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 23

15. Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Page

Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2

Adding/Replacing Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3

Two Car Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3

Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3

Remote Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4

Remote Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4

Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5

Silent Arming/Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5

Passive Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5

Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6

Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6

Optional Coded Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6

Automatic Rearming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7

Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7

Ignition Door Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8

Ignition Door Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8

Dome Light Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8

Auxiliary Function Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8

Disarm with Auxiliary Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8

Remote Sensor Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9

ScyNet Network Remote Car Start Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9

Optional Hands-Free Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9

Mounting the Control unit Page 12
Mounting the Siren Page 12
Mounting the Shock Sensor Page 12

16-Pin Main Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13

Starter Defeat Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14

Plug-in Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14

Real-time Sensor Adjustment Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14

Jumper Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15

Entering System Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16

Default Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16

Programmable System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16

Branch Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 17

About YYour SSystem

The ScyTek Galaxy 3000 Plus is a state-of-the-art vehicle security system featuring a built-in
"ScyNet Network Port" that allows direct connection of optional accessory modules and a PC
interface offering expanded system operation. With proper installation this system will provide
superior protection and performance for many years to come.

System Contents:

• Main Unit with built-in ScyNet Network Interface Port

• Two 5-Button Random Code Remote Transmitters

• High Output 6-tone Siren

• Dual Stage Shock Sensor

• Status LED

• Coded Emergency Override / Valet Switch

Optional ScyNet Network Interface Accessories:

• ScyNet Network Interface Software

• Two-Way FM Paging Module w/ LCD Transmitter

• Remote Engine Start Module

• Channel Expander w/ 7 Programmable Outputs

Options and Convenience Features

*

This ScyTek system includes several optional inputs and outputs allowing the creation of a
completely personalized security and convenience system by offering many optional features
such as:

· Second Car Operation

· Remote Door Locking

· Two Stage Door Unlocking

· Starter Defeat

· Horn Honk

· Illuminated Entry / Exit

· Remote Window Control

· Remote Car Start

*May require additional parts and/or labor, see store for details.

Some of the features described in this manual may require additional parts and/or labor, and may not be included
as part of the standard installation of this unit. Additionally, many features of this security system have
selectable options that must be activated or programmed during the system’s installation. These items will be
identified in the following sections. Please discuss these features and any questions you may have regarding the
installation of this product with Your Authorized Dealer.

PLEASE NOTE:

· Extended Range Antenna

· Power Trunk / Hatch Release

· Glass Breakage Sensor

· Radar Sensor

· Auxiliary Lighting Control

· Stereo System Valet

· Remote Head Lamp Control

· Back-up Battery Siren

Galaxy 3000 Plus - Page 1

Remote TTransmitters

Remote Transmitter Description

LED

Button 1 Button 2

Button 5

Button 3 Button 4

The Galaxy 3000 Plus is supplied with two 5-button Remote Transmitters used to control system operations.

Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure
the functionality of the transmitter buttons. The standard (default) setting for operation of the transmitters
is described below.

Button 1

Arms the system and when held for 2 seconds, activates the system’s Panic feature. Button 1 also

locks the doors when the system is in Valet Mode.

Button 2

Disarms the system. Pressing Button 2 again operates the Passenger Unlock feature (if installed).

Button 2 also unlocks the doors when the system is in Valet Mode.

Button 3

Activates the Auxiliary 1 output. This output will remain on for as long as the button is pressed.

Button 4

Activates the Auxiliary 2 output. This output will remain on for as long as the button is pressed.

Button 5

each time it is pressed, allowing access to additional features or multiple car operation. Pressing the Shift
Button then Button 3 activates the Channel 4 output.

Each time the Shift Button is pressed, the LED on the transmitter will illuminate and the transmitter
functions will shift to the next page, allowing access to another set of features. Once shifted to another
page (there are 4 pages total), the transmitter will remain on that page for 10 seconds or until a button is
pressed, then return to page 1. Each time a transmitter button is pressed and held, the LED will flash a
number of times to indicate from which page it is transmitting. Under normally operation, only pages 1 and
2 are used. Pages 3 and 4 are usually used for Two Car Operation (see page 3) or optional expansion
modules.

is the Page Shift button. The Page Shift button will change the function of Buttons 1 through 4

Page 2 - Galaxy 3000 Plus

Adding/Replacing Transmitters

To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired
transmitters ready and follow the steps below.

Note: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored
transmitter codes, be sure to program all 4 transmitter memory locations.

To program the transmitter(s):

1. Turn on the ignition key On, Off, On, Off, and back On.

· The siren will chirp 3 times.

2. Press and hold the Override switch for 5 seconds.

· The siren will chirp 5 times.

· The LED will illuminate.

3. Press Button 1 on the first transmitter.

· The siren will chirp once.

4. Press Button 1 on the first transmitter again.

· The siren will chirp twice to indicate it has learned the code.

5. Repeat steps 3 and 4 for each transmitter (up to 4).

6. Turn off the ignition key.

Two Car Operation

If two vehicles are equipped with Galaxy 3000 Plus systems, for convenience both can be operated using
the same remote transmitter. If all four transmitters are to be used with both cars, program transmitters
A and B into the first vehicle in the manner described above. Program transmitters C and D by pressing
the Shift button twice before performing steps 3 and 4 above.

When finished programming the first vehicle, program transmitters C and D into the second vehicle as
normal, then program transmitters A and B by pressing the Shift button twice before performing steps 3
and 4 above.

When programmed in this manner, the driver of the first car can also operate the second vehicle by pressing
the Shift button twice and the desired function button.

Battery Replacement

Your Galaxy Remote Transmitter uses a 12 volt alkaline battery (type 23A), which will require replacement
in time. Depending on the amount of use, the battery may last up to six months or more before it needs
replacement.

When the battery needs replacing, the system’s operating range will decrease or the transmitter LED may
not be as bright.

In order to change the battery, first remove 2 screws from the back of the transmitter and separate the top
and bottom halves of the case.

While replacing the battery make sure that the positive and negative terminals are positioned correctly, then
carefully reassemble the transmitter case.

Galaxy 3000 Plus - Page 3

System OOperation

Remote Arming

The system monitors 6 independent areas (
sensor input, and the network port for future expansion.

To Arm the System:

1. Turn off the ignition.

2. Press Button 1.

· The siren will chirp once.*

· The doors will lock.

· The parking lights will flash once.

· The LED will turn on red, to indicate the starter defeat is activate.

3. 10 seconds after Arming:

· The LED will start blinking to indicate that the doors, hood, trunk and sensor inputs are being
monitored.

* During Arming, if the system detects a bad sensor or an open zone, the system will chirp 4 additional

times and ignore that input, but keep all other areas protected.

Once Armed, the alarm will trigger when any of the following occurs:

· The doors are opened.

· The hood or trunk is opened.

· The shock sensor detects an impact to the vehicle.

· An optional sensor is disturbed.

When the alarm triggers, the siren will sound, the horn will honk, and the parking lights will flash. If
the system is triggered by the doors, hood, or trunk, the system will alarm for 45 seconds. If triggered
by the sensor inputs, the system will alarm for 30 seconds.

In the event the alarm is triggered and remains triggered continuously by the same sensor or input
during a single arming cycle, that sensor or input will be automatically bypassed until the next time
the system is armed.

If the Shock Sensor detects a light impact to the vehicle the siren will chirp 5 times as a warning
indication.

Remote Disarming

To Disarm the System:

Press Button 1.

· The siren will chirp twice.*

· The doors will unlock.

· The parking lights will flash twice.

· The dome light will turn on.

· The LED will turn off.

* During Disarming, if the system was triggered while away from the vehicle, the siren will chirp 3 times, the parking

lights will flash 3 times, and the LED will flash to indicate triggered zone. See

zones

) while armed: doors, hood, trunk, shock sensor, optional

Tamper Alert

for zone listing.

Page 4 - Galaxy 3000 Plus

Tamper Alert

If the system was triggered while away, the LED will flash to indicate which zone triggered the system after
disarming and turning on the ignition. The LED indication will repeat for 20 seconds.

LED Flashes (60 seconds):

1 flash = optional sensor
2 flashes = shock sensor
3 flashes = network based sensor
4 flashes = door
5 flashes = trunk
6 flashes = hood (if network remote start module connected)
7 flashes = reserved for future use
8 flashes = reserved for future use
9 flashes = reserved for future use
10 flashes = main power interrupt

example: flash-flash-pause-flash-flash-pause = shock sensor

Silent Arming/Disarming

The Galaxy 3000 Plus system can be programmed to operate the system without Arm and Disarm chirp
indications. When programmed for full-time silent operation, the siren will sound only when the system is
triggered.

The system is also capable of temporary silent operation if desired. Pressing the Shift button before Arming
or Disarming the system will bypass the chirp confirmations and allow one-time silent operation.

Note: The open zone warning chirps will not be bypassed when the system is Armed or Disarmed silently.

Passive Arming

When programmed for the optional Passive Arming feature, the system arms itself automatically, each time
the ignition is turned off and all of the doors, hood, and trunk are closed.

To start the Passive Arming Process:

1. Turn off the ignition.*

2. Open the door and exit the vehicle.

· Once all doors are closed and the dome light is off, the LED will begin flashing rapidly.

· The parking lights will flash twice indicating the Passive Arming sequence has begun.

3. After 30 seconds,

· The siren will chirp.

· The parking lights will flash.

· The doors will lock.**

· The status LED will begin flashing.

4. The system is now armed.

* The ignition must have been on for

** If the Passive Locking feature is selected.

To temporarily disable Passive Arming, turn on the ignition then turn off within 5 seconds. The siren will
chip once indicating the system will not passively arm until the ignition is cycled again.

The system can be programmed to provide an Entry Delay when the system is armed passively. Upon
opening the door the siren will chirp for 10 seconds allowing time to enter the vehicle and turn on the
ignition before the full siren output is triggered.

at least

5 seconds or the Passive Arming sequence will be disabled.

Galaxy 3000 Plus - Page 5