Scytek Galaxy G40RS, Galaxy G35RS User's Manual

GALAXY G40RS

AUTOMATIC TRANSMISSION

WITH SEPERATE LOCK/UNLOCK BUTTONS

REMOTE START SYSTEM

PRODUCT MANUAL

G 40RS - Page 1

PLEASE NOTE:

Some of the features described in this manual may require additional parts and/or labor, and may not be included
as part of the standard installation of this unit. Additionally, many features of this security system have
selectable options that must be activated or programmed during the system’s installation. These items will be
identified in the following sections. Please discuss these features and any questions you may have regarding the
installation of this product with Your Authorized Dealer.

Limited Lifetime Warranty

This vehicle remote start system is warranted to the original purchaser, to be free from defects in
material and workmanship. The manufacturer will repair or replace at its option, and free of
charge for the first twelve (12) months, any part that proves defective in material or workmanship
under normal installation, use, and service, provided the product is returned to the manufacturer
freight prepaid. After the first 12 month warranty period there will be a maximum service charge
of $25.00 per calendar year (if required) for repair and/or replacement of any defective parts.

A copy of the original purchase and installation receipt must accompany any products
returned for warranty service. Warranty is limited to defective parts and/or replacement parts

only and excludes any incidental, and consequential damages connected therewith.

WARRANTY OF INSTALLATION LABOR, REMOVALAND RE-INSTALLATION CHARGES ARE
NOT THE RESPONSIBILITY OF THE MANUFACTURER.

Note: This Warranty is voided if the product was not installed by an
Authorized ScyTek Dealer..

FCC ID: OARRXAM2000

This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause
undesired operation

Remote Transmitter Description

The

G40RS

is a state-of-the-art remote starting system

is supplied with two 4-button Remote

Transmitters used to control system operations.
The built-in remote start feature is designed to offer maximum convenience by remote starting your

vehicle’s engine, turning on the heater/air conditioner, and then running for a pre-determined time to
provide a comfortable environment once you enter your vehicle.

ScyTek Electronics Inc. and its VENDORS shall not be liable for any accident resulting from the use of this
equipment. This system is designed to be professionally installed into a car or vehicle in which all items,
such as parking brake and all associated components, Hood switches, transmission shift linkage, throttle
linkage, and all engine safety features, are in perfect working condition.

Do not ever Install G40RS in vehicles equipped with MANUAL TRANSMISSION.

DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is
adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon. To
ensure the safety and security of the system while it is remote started, the G40RS Starter employs several
safeguards. In the event the brake pedal is pressed while the engine is remotely running, the remote
start will immediately shutdown to prevent unauthorized users from attempting to drive the vehicle. The
system is equipped with a hood pin input to prevent access to the engine compartment while the vehicle
is remotely running. Finally, the Valet Mode prevents the remote start feature from operating in the event
the vehicle is to be serviced.

Button 1

Locks the doors and when held for 5 seconds, activates the system’s Car locator feature.

Button 2

unlocks the doors.

Button 3

N.A

Button 4

Activates and deactivates

the Remote Start feature.

Page 2 - G 40RS

Remote Transmitters

Button 1

Button 2

LED

Button 3

Button 4

G 40RS - Page 3

Adding/Replacing Transmitters

To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired
transmitters ready and follow the steps below.

Note: Up to four transmitters can be programmed to operate the system. To erase any previously stored
transmitter codes, be sure to program all 4 transmitter memory locations.

To program transmitter(s):

1. Turn the ignition key On, Off, On, Off, and back On.

· The parking lights will flash 3 times.

2. Press and hold the Override switch for 5 seconds.

· The parking lights will flash 5 times.

· The LED will illuminate.

3. Press Button 1 on the first transmitter.

· The parking lights will flash once.

4. Repeat steps 3 and for each transmitter (up to 4).

5. Turn off the ignition key.

· The parking lights will flash 3 times.