Screen Research ILT2 User And Installation Manual

Download

User and Installation Manual

Page 1

ILT2 motorized screens INTERFACE

Manual

Connections ILT-4 Somfy

Page 2

Your screen is equipped with Somfy ILT2 motors which allows more presets than standard Somfy Motors (LT50 or LS40) This screen needs to be controlled could be controlled using two controllers:

SOMFY® interface called “SOMFY® 4ILT interface” RS485 (+ converter RS232)

Following instructions concern the “SOMFY® 4ILT control box”.

The following interfaces can be used to connect up to 4 ILT2 Somfy motors on the 2-way or 4-way masked screens.

There are different versions available. In the following table you can compare the various settings based on the version.

Version

Included parts

Set or change end limits motors

Set or change Preset ratio

MCS-ILT-4

only interface

with MCS-ILT-T setting

tool (not included)

with Computer or

automation System

(not included)

MCS-ILT-4-IR

with infrared

remote control

with IR remote control

(included)

with IR remote

control (included)

MCS-ILT-4-IP

with TCP/IP

control

with MCS-ILT-T setting

tool (not included)

with Computer or

automation System

(not included)

CRESTRON® interface developed for ILT2 motors called “C2N-SSC-2” RS232

For the CRESTRON interface please refer to the specific CRESTRON documentation.

Manual

Connections ILT-4 Somfy

Page 3

INTRODUCTION

This manual is an integral part of the product and must be read and understood in all its parts for safety reaso ns. It contains norms and directions for correct and safe use of t he interface. The manual should never be separ ated from the product; it must be stored in a suitable place to ensure its integrity, and in such a way as to be e asily consulted by authorised personnel. Product user shall be responsible for the manual’s safekeeping. User shall also be responsible for checking the screen’s functionality and for the repair or replace ment of any damaged parts that could pose a hazard. Images contained in this manual are intended to provide a deta iled description of the product’s functions, characteristics and procedures. Any slight dif ference, depending on the model represented, will not change the meaning that the imag es convey.

GENERAL CHARACTERISTICS OF THE PRODUCT

The product are manufactured in compliance with the following EC directives: 2006-95-EC low voltage directive (LVD), 2004-108-EC electromagnetic c ompatibility (EMC), and the following reference standards mentioned in the European directives: EN 61058 -1; EN 50366:2003 - EN 61000-6-1; EN 61000-6-3 The RS485 4ILT Interface is a motor controller for mult i ratio motorized projection screens designed to be integrated into the projection screen cases. It can control up to 4 SOMFY ILT motors. I t can be interfaced with universal infra red remote controls, a RS485 data line or a videoprojector through a trigger. Any other use shall be considered improper and is expressly forb idden. The manufacturer shall not be liable for damages resulting from improper use, or for a ny uses other than those set out in this manual.

GENERAL SAFETY NORMS

- Always read the instructions and warnings set out in this manual very carefully before using the product or before performing any ma intenance interventions.

- Before and during use, check that the screen poses no risk of h azard.

- Do not tamper with, remove or damage any part or compone nt of the product.

- Do not perform screen maintenance when the motor is on (fo r maximum safety, unplug the power cord). All interface are covered by guarantee; validity of the same shall be subject to user’s full compliance with the instructions contained in this manual.

WARNING: Faulty installation may compromise the safety of th e product’s operators; manufacturer shall not be held liable for damage s to persons or things resulting from faulty installation, improper use, insufficient or inadequate m aintenance of the screen. Manufacturer shall not be held responsible for problems a ssociated with installation errors. Screen installation, electrical connections and verificat ions in case of malfunction of motorised rolling screens must be performed by authorised vendor o r by personnel that is informed and trained in electrical hazards. The connection cable cannot be replaced. If the cable is damaged the screen must be replaced. Tamperin g with end stops or piercing the seal placed over holes shall entail the forfeiture of the guarantee. For any n ecessary clarifications please contact our technical office.

WARNINGS AND RECOMMENDATIONS FOR CORRECT USE

These interfaces ar e suitable for use in indoor ambiences in normal (0 /+ 60 °C) temperature and humidity conditions. Special cau tion must be exercised when us ing the products out of doors, particularly with regard to temperature conditio ns and in the presence of dust. ATTENTION: Do not allow children to play with fixed con trol devices. Keep remote controls out of the reach of children. Monitor motors when in movement and keep people awa y from them until they stop.

TECHNICAL CHARACTERISTICS

• Power supplier: 90 ÷ 225 Vac 50/60 Hz

• Protection class: IP20 (of undamaged box)

• Operating temperature: 0 ÷ 60 °C

• Dimension / weight: 137 x 80 x 40 mm

Notes to the product’s Technical Specifications: With an universal IR remote control

- Please refer to the universal IR remote co ntrol instructions to learn the codes from a Somfy 8 channels remote control to the universal IR remote control.

- If there is no specific instructions, please contact your Screen Research local retailer. With a trigger input

- The trigger input allows to synchronize the motorized projection screen with a videoprojector (For videoprojector with DC12V output).

- When the videoprojector will be powered ON, the interface wil l put the projection screen in Format 1 position.

- When the videoprojector will be powered O FF, the interface will put the projection screen in Format 8 position. With a RS485 data line The appendix (cf page 34) describes the SOMFY RS485 protoco l, which is used to communicate with the RS485 4ILT Interface. The RS485 protocol supports bi-directional communication between a host and the interface. The term «Host» refers to the device initiating communicat ion with the interface, usually a computer-based system. RS485 communication standard All signals on the physical link between devices sho uld comply with EIA/TIA-485-A standard. Recommended cable : Shielded , two twisted - pair type 22 - 24 AWG (120 Ω) Communication mode : half-duplex Each character is coded as follow :

Character coding

Baud Rate

4800

+/-1%

Start bit

Logical Level 0

Data bits

Less significant bit transmitted first

Parity

Odd Stop bit

Logical Level 1

DISPOSAL OF PRODUCT

As is the case for the installation of this device, its end -of-life disposal must be handled by qualified personnel. This product is made up of various types of material: som e can be recycled, others must be disposed of. Please enquire about recycling and disposal regulations in force in your territory for this type of produc t. As indicated by the symbol on the left, dumping this produ ct in domestic waste bins is forbidden. Please dispose of separately, according to regulations in force in your territory, or return the product to the dealer when you buy a new one. Attention: under local regulations severe fines may apply in case of improper disposal of this product.

WARRANTY

These control units are guaranteed for a 24 -month period. Validity of the warranty shall commence on the date of purchase, which must be documen ted by the purchase document when requesting a repair service or replacement. The warranty covers any damages or malfunction resulting from the normal use of th ese products, and the free replacement of any components that should present manufacturing faul ts. The service includes collection and delivery, by a courier of the manufacturer’s choice and at the manufact urer’s expense (this applies only to warranties valid in Italy and Poland). The warranty does not apply in case of improper use, insta llation, tampering or repair on the part of persons not authorised by the manufacturer. Components th at present normal wear and tear as a result of their use or of particular weather o r environmental conditions are not covered by this warranty. Products that ar e damaged during transportation or handling are not covered by this warranty. You are invited to check the good s very carefully when you receive them.

Products returned for repair without the manufacturer’s r eturn authorization (RMA) and without suitable packaging will not be accepted. The manufacturer reserves the right to verify the existence of th e requisites for the warranty’s validity.

Manual

Connections ILT-4 Somfy

Page 4

General connections

12V Trigger

IR Sensor

RS485

Adapter RS232

+ = 5  30V G = Ground

NC = Not connected

RS485 B RS485 A G = Ground

RS485 A = - RS232 RS485 B = + RS232

Transmission distance: 1000 meters/3281 feet

ILT2 motors connections

SCREEN

ILT plug M1

ILT plug M2

ILT plug M3

ILT plug M4

Fixed 4 Way

Left Mask

Right Mask

Top Mask

Bottom Mask

Fixed 2 Way lateral

Left Mask

Right Mask

Not connected

Fixed 2 Way lateral with Deco

Left Mask

Right Mask

Deco Mask

Not connected

Fixed 2 Way Top-Bottom

Not connected

Top Mask

Bottom Mask

Rolling 4 Way

Projection Fabric

Top Mask

Left-Right Mask

Not connected

Rolling Top-Bottom

Projection Fabric

Top Mask

Not connected

MOTOR SETTING

ENGLISH

Page 5

End limits motors setting with MCS-ILT-T setting tool

1. Connect the setting tool to the motor with the phone cable. Th e LED light turns on.

2. Push the selector switch into the up position.

3. Press the UP or DOWN button of the setting tool. Check if the UP push button controls the UP direction and the DOWN one the DOWN motion. If not, reverse the rotation direction simply by pushing the STOP push button (1 sec).

4. Adjust the screen to the required position up limit by pr essing the UP or DOWN buttons.

5. Push the switch to its MIDDLE position. The UP limit recorde d..

6. For the DOWN limit, slide the to the DOWN position.

7. Adjust the screen to the required DOWN lim it, by pressing the UP or DOWN button s.

8. Do not press the STOP button once the DOWN limit is reach ed. Just let go and the screen will stop.

*NOTE: If you do this then the motor will reverse directions and will not function when you set the switch to the MIDDLE position to record the DOWN limit. NEW LIMITS WILL NEED TO BE RECORDED AGAIN.

9. Push the selector switch to its MIDDLE position to reco rd the DOWN limit.

10. Check the UP & DOWN limits just set.

End limits motors setting with IR transmitter

MOTOR SELECTION LOGIC:

-Use the “First” or “Next” button to select on e of the motors. The selected motor will acknowledge by doin g a small jog.

1) The “First” button to select the first moto r connected to the interface.

2) The “Next” button to select the next motor connected to the interface.

3) The “All” button to select all the motors connected to the interface.

Once a motor is selected, you can control it individually. After 2 min without any operation, all motors will rea ct again to any operation.

MOTOR END LIMITS SETTING

1 - Adjust UP end limit: A) Select the motor B) To enter in setting mode, press the “Prog” button of th e remote control until the screen jogs. C) Press the UP button until the motor jogs. D) Then with the UP or DOWN buttons, move the screen to the des ired up limit. Note: If the direction of rotation is not correct, press the STOP button until the screen jogs. E) Press the Prog button to confirm the limit until the mo tor jogs.

2 - Adjust DOWN end limit: A) Select the motor B) To enter in setting mode, press the “Prog” button of th e remote control until the screen jogs. C) Press the DOWN button until the motor jogs. D) Then with the UP or DOWN buttons, move the screen t o the desired up limit. E) Press the Prog button to confirm the limit until the m otor jogs.

3 - Readjusting the end limit(s) Please refer to: UP and DOWN end limits setting (1 and 2 point)

Format s

etting with IR transmitter

SETTING LOGIC:

-Buttons 1 to 7 will be used to set 1 to 7 f ormats.

-By default, buttons 1 to 7 are not set, button with white backg round stands for the user "Open" or "Full closure" or "Deco Mask" movements.

FORMAT SETTING: A) With the “selection motor buttons” and “Up – Do wn buttons” to move each motor (mask or projection fabric) to the desired

position/format.

B) then press the selected button (eg : button1) until all the screens jog.

-TIPS: During the adjustment of the screen, if you press and hold the UP or DOWN button, the screen moves step by step. You can

use this function for a better adjustment of the screen.

CALL A FORMAT: To call a format, press on the desired form at button.

READJUSTING A FORMAT: Please refer to : FORMAT SETTING

DELETE A FORMAT: A) Press the format button corresponding to the format to delete. The screens go to the memorized position. B) Press the corresponding format button until all the screens jog. The format is deleted.

INSTRUCTION

ENGLISH

Page 6

SOFTWARE PROVIDED

To control the screens with ILT4 and control serial (RS232 or R S485) are available the following software: EventGhost_0.3.7.r1170

(Software: http://www.eventghost.net/downloads/E ventGhost_0.4.1.r1722_Setup.exe )

(Download package: www.screenresearch.com/websit e/documents/software_current/ILT-interface.rar )

Description:

EventGhost Software is an advanced, easy to use and extensib le automation tool for MS Windows. It can use different input/output devices to trigger macros (Such as serial COM port of your Computer),

that on their part control a computer and its atta ched hardware. These remote controls has been developed to set and control easily the motors of your X -Mask using your Computer. It is a tool for Installer

usage ONLY to make on-site installation by RS485 Com mands easier.

FILE PROVIDED

Remote control ILT2 motors.xml

THIS SOFTWARE WORKS ONLY WITH SOMFY 4ILT INTERFACE

COM port parameter

Macro for 4way masking or 2 way masking screens (select and hit F5 on your keyboard or to enable the remote control)

INSTRUCTION

ENGLISH

Page 7

INSTALLATION

SCREEN and INTERFACE:

A) Connect each motor to the power supply B) Connect the ILT interface to the power supply and wait initialization time of 15 seconds C) Plug RJ9 from each motors into the ILT Interface D) Plug your RS485 cable between your computer and the ILT interface as shown in the documentation provided

SOFTWARE:

A) Install and Launch EventGhost Software

B) Load/Open file " Remote control ILT2 motors.xml”:

1 - select the “file - open…” in the toolbar 2 - search the “xml file” in your PC 3 - select the “open” in the windows

C) Set the COM Port parameters:

1 - select the “Plugin: Serial Port” - open…” in the toolbar 2 - open menu with right button and select “Configure Item” 3 - check the parameter: - 4800 bauds,

- 8 bits,

- Parity Odd,

- 1 stopbits,

- None flow control.

4 – confirm with “OK”

D) Open the remote control

1 - select the macro (not double-click)

If your Screen is a 4 way masking : select the "XMask2 4way Masking Remote Control" If your screen is a 2 way masking : select the "XMask2 2way Masking Remote Control" If your screen is a Motorized Topmasking : select the "Motorized TopMask Remote Control"

2 - select the “Executive item” in the toolbar

E) The remote control appears on your desktop.

INSTRUCTION

ENGLISH

Page 8

DATA PARAMETER SERIAL

Commands

Code ASCII

Code Hexadécimal

Select format 1

7FF3FBFFFFFF000000FE0668

\x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFE\x06\x 68

Select format 2

7FF3FBFFFFFF000000FD0667

\x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFD\x06\ x67

Select format 3

7FF3FBFFFFFF000000FC0666

\x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFC\x06\ x66

Select format 4

7FF3FBFFFFFF000000FB0665

\x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFB\x06\ x65

Select format 5

7FF3FBFFFFFF000000FA0664

\x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFA\x06\ x64

Select format 6

7FF3FBFFFFFF000000F90663

\x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xF9\x06\ x63

Select format 7

7FF3FBFFFFFF000000F80662

\x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xF8\x06\ x62

Select “OPEN” “FULL CLOSURE” “DECO”

7FF3FBFFFFFF000000F70661

\x7F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xF7\x06\ x61

Save format 1

6FF3FBFFFFFF000000FE0658

\x6F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFE\x06\x 58

Save format 2

6FF3FBFFFFFF000000FD0657

\x6F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFD\x06\ x57

Save format 3

6FF3FBFFFFFF000000FC0656

\x6F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFC\x06\ x56

Save format 4

6FF3FBFFFFFF000000FB0655

\x6F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFB\x06\ x55

Save format 5

6FF3FBFFFFFF000000FA0654

\x6F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFA\x06\ x54

Save format 6

6FF3FBFFFFFF000000F90653

\x6F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xF9\x06\x53

Save format 7

6FF3FBFFFFFF000000F80652

\x6F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xF8\x06\ x52

Save “OPEN” “FULL CLOSURE” “DECO”

6FF3FBFFFFFF000000F70651

\x6F\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xF7\x06\ x51

Reset format 1

6EF3FBFFFFFF000000FE0657

\x6E\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFE\x06\ x57

Reset format 2

6EF3FBFFFFFF000000FD0656

\x6E\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFD\x06 \x56

Reset format 3

6EF3FBFFFFFF000000FC0655

\x6E\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFC\x06\ x55

Reset format 4

6EF3FBFFFFFF000000FB0654

\x6E\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFB\x06\ x54

Reset format 5

6EF3FBFFFFFF000000FA0653

\x6E\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFA\x06\ x53

Reset format 6

6EF3FBFFFFFF000000F90652

\x6E\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xF9\x06\ x52

Reset format 7

6EF3FBFFFFFF000000F80651

\x6E\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xF8\x06\ x51

Reset “OPEN” “FULL CLOSURE” “DECO”

6EF3FBFFFFFF000000F70650

\x6E\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xF7\x06\ x50

Move up all motors

67F2FBFFFFFF000000FFFE074E

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFF\xFE\x07\x4E

Move up motor 1

67F2FBFFFFFF000000FEFE074D

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFE\xFE\x07\x4D

Move up motor 2

67F2FBFFFFFF000000FDFE074C

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFD\xFE\x07\x4C

Move up motor 3

67F2FBFFFFFF000000FCFE074B

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFC\xFE\x07\x4B

Move up motor 4

67F2FBFFFFFF000000FBFE074A

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFB\xFE\x07\x4A

Move down all motors

67F2FBFFFFFF000000FFFD074D

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFF\xFD\x07\x4D

Move down motor 1

67F2FBFFFFFF000000FEFD074C

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFE\xFD\x07\x4C

Move down motor 2

67F2FBFFFFFF000000FDFD074B

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFD\xFD\x07\x4B

Move down motor 3

67F2FBFFFFFF000000FCFD074A

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFC\xFD\x07\x4A

Move down motor 4

67F2FBFFFFFF000000FBFD0749

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFB\xFD\x07\x49

Move stop all motors

67F2FBFFFFFF000000FFFC074C

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFF\xFC\x07\x4C

Move stop motor 1

67F2FBFFFFFF000000FEFC074B

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFE\xFC\x07\x4B

Move stop motor 2

67F2FBFFFFFF000000FDFC074A

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFD\xFC\x07\x4A

Move stop motor 3

67F2FBFFFFFF000000FCFC0749

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFC\xFC\x07\x49

Move stop motor 4

67F2FBFFFFFF000000FBFC0748

\x67\xF2\xFB\xFF\xFF\xFF\x00\x00\x00\xFB\xFC\x07\x48

Get Screen Status all

77F3FBFFFFFF000000FF0661

\x77\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFF\x06\x61

Get status motor 1

77F3FBFFFFFF000000FE0660

\x77\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFE\x06\x60

Get status motor 2

77F3FBFFFFFF000000FD065F

\x77\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFD\x06\x5F

Get status motor 3

77F3FBFFFFFF000000FC065E

\x77\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFC\x06\x5E

Get status motor 4

77F3FBFFFFFF000000FB065D

\x77\xF3\xFB\xFF\xFF\xFF\x00\x00\x00\xFB\x06\x5D

RS485 REMOTE

ENGLISH

Page 9

SOMFY INFRARED CODE

"1"

0000 006b 0000 0017 0015 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 02a3 0007 011d 0006 00be 0006 011e 0006 00bd 0007 011f

0006 00bc 0007 011e 0007 00bd 0006 00be 0006 00bd 0007 00bb 0008 03d0

Alternate Pattern

0000 006b 0000 0017 0015 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 02a4 0007 011c 0007 011e 0006 011e 0006 00bd 0007 011e

0006 00be 0006 011e 0006 00be 0006 00be 0006 00bc 0007 00bc 0007 03d1

0000 006b 0000 0017 0015 0013 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 02a3 0008 011c 0007 00bd 0006 011f 0006 00bd 0007 011d

0007 00be 0006 011e 0006 00be 0006 00bd 0006 00be 0006 00bd 0006 03d1

0000 006b 0000 0017 0015 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 02a3 0007 011d 0006 011e 0007 011e 0006 00bd 0006 011f

0006 00be 0006 011e 0006 00be 0006 00bd 0007 00bd 0006 00bd 0006 03d1

"2"

0000 006b 000b 0017 0015 0012 0015 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 02a3 0007 011d 0006 00be 0006 011d 0007 00bd 0007 011d

0007 00be 0006 011e 0006 00be 0006 00bc 0008 00bd 0006 011d 0007 036a 0015 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 02a3

Alternate Pattern

0000 006b 000b 0017 0015 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 02a3 0007 011d 0006 00bd 0007 011e 0006 00be 0006 011e 0007 00bc 0007 011d 0007 00be 0006 00be 0006 00bd 0007 011d 0006 036b 0015 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 02a3

"3"

0000 006b 000b 0017 0015 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 02a3 0007 011d 0006 011e 0006 011f 0006 00bd 0006 011f

0006 00bd 0007 011d 0007 00bd 0007 00bd 0006 011e 0007 00bb 0007 036b 0015 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 02a3

Alternate Pattern

0000 006b 000b 0017 0015 0013 0014 0013 0015 0012 0014 0013 0014 0013 0015 0012 0015 0012 0014 0013 0015 0012 0015 0012 0014 02a7 0008 011e 0006 011f 0007 0120 0006 00bf 0006 0120 0006 00be 0007 0120 0006 00be 0007 00bd 0008 011f 0006 00be 0007 036f 0016 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 02a7

0000 006b 000b 0017 0016 0012 0015 0012 0015 0012 0015 0012 0015 0013 0014 0013 0014 0013 0014 0012 0015 0012 0015 0012 0015 02a7 0007 011e 0007 00be 0006 0120 0007 00bd 0007 0120

0007 00be 0006 0120 0006 00be 0007 00bf 0006 011f 0007 00bd 0007 0370 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7

"4"

0000 006b 000b 0017 0016 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 02a3 0007 011d 0006 011e 0007 011e 0006 00bd 0006 011e 0007 00be 0006 011d 0007 00bd 0007 00bc 0007 011e 0006 011e 0006 0305 0015 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 02a3

Alternate Pattern

0000 006b 000b 0017 0015 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 02a3 0007 011c 0007 00be 0006 011e 0006 00bd 0007 011e 0006 00be 0006 011d 0007 00be 0006 00bd 0007 011e 0006 011d 0006 0305 0016 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 02a3

0000 006b 000b 0017 0016 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 0012 0015 02a7 0007 011e 0007 00be 0006 0120 0006 00bf 0006 0120

0007 00bd 0007 0120 0006 00bf 0006 00be 0007 011f 0007 011f 0006 030a 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0012 0015 02a7

0000 006b 000b 0017 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7 0007 011e 0007 0120 0006 0120 0006 00bf 0006 0120

0006 00bf 0006 0120 0006 00be 0007 00be 0006 011f 0007 011f 0006 030a 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7

"5"

0000 006b 000b 0017 0015 0013 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 02a3 0007 011d 0006 011e 0007 011e 0006 00bd 0006 011e 0007 00bd 0007 011e 0006 00bd 0007 011e 0006 00bd 0007 00bc 0007 036a 0015 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 02a3

Alternate Pattern

0000 006b 000b 0017 0015 0012 0015 0012 0015 0013 0014 0012 0015 0012 0015 0012 0015 0013 0014 0013 0014 0012 0015 0012 0015 02a7 0007 011e 0007 011f 0006 0120 0006 00be 0007 011f

0007 00bf 0006 011f 0007 00bf 0006 011f 0007 00be 0007 00bd 0007 036f 0016 0013 0014 0012 0015 0012 0015 0012 0015 0012 0015 0013 0014 0012 0015 0012 0015 0013 0014 0012 0015 02a7

"6"

0000 006b 000b 0017 0015 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 02a3 0007 011d 0006 00be 0006 011d 0007 00bd 0007 011f 0006 00bc 0007 011e 0006 00be 0006 011e 0006 00bd 0007 011d 0006 0306 0015 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 02a3

Alternate Pattern

0000 006b 000b 0017 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0012 0015 02a7 0007 011e 0007 00be 0007 011f 0007 00be 0006 0121

0006 00bd 0007 0120 0006 00be 0007 0120 0006 00bf 0006 011f 0006 030a 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7

"7"

0000 006b 000b 0017 0015 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 02a3 0007 011c 0007 011d 0007 011f 0006 00bd 0006 011f 0006 00bd 0007 011e 0006 00bd 0006 011f 0006 011e 0006 00bc 0007 0305 0015 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0015 0012 0014 0013 0014 02a3

Alternate Pattern

0000 006b 000b 0017 0015 0013 0014 0013 0014 0012 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0012 0015 02a7 0007 011e 0007 011e 0007 0120 0006 00bf 0006 0120

0006 00be 0007 0120 0006 00bf 0006 011f 0007 0120 0006 00be 0006 030a 0015 0012 0015 0013 0014 0013 0014 0012 0015 0012 0015 0013 0014 0013 0014 0013 0014 0013 0014 0012 0015 02a7

0000 006b 000b 0017 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7 0007 011f 0006 00be 0007 011f 0007 00bd 0008 0120

0006 00bd 0008 011f 0007 00be 0006 0120 0006 0120 0006 00be 0006 030a 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7

"OPEN" “FULL CLOSURE”

“DECO”

0000 006b 000b 0017 0015 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 02a3 0007 011d 0006 011e 0006 011e 0006 00be 0006 011e 0007 00bc 0007 011e 0007 00bd 0006 011e 0006 011e 0007 011c 0007 02a0 0015 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 02a3

Alternate Pattern

0000 006b 000b 0017 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7 0007 011f 0006 011f 0007 0120 0006 00bd 0008 011f 0007 00be 0007 011f 0007 00be 0006 0120 0006 0120 0006 011f 0006 02a4 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7

"UP"

0000 006b 0000 0017 0015 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0014 02a4 0007 011d 0006 011d 0007 011e 0006 00be 0006 011e

0007 00bc 0007 00be 0006 00bd 0007 00bc 0007 00be 0006 011c 0007 03d1

Alternate Pattern

0000 006b 0000 0017 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 02a3 0007 011d 0007 00bd 0006 011f 0006 00bc 0007 011f

0006 00bd 0007 00bd 0006 00bd 0007 00be 0006 00bd 0006 011e 0006 03d0

0000 006b 0000 0017 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7 0007 011f 0006 0120 0006 011f 0007 00be 0006 0121

0006 00bd 0008 00be 0006 00bf 0006 00be 0007 00bf 0006 011f 0006 03d6

0000 006b 0000 0017 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7 0007 011f 0006 00bf 0006 0120 0006 00bf 0006 0120

0006 00be 0007 00bf 0006 00be 0007 00bd 0008 00bd 0008 011e 0007 03d5

"DOWN"

0000 006b 0000 0017 0015 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 02a3 0007 011d 0006 00be 0006 011e 0006 00be 0006 011f

0006 00bd 0006 00be 0006 00bd 0007 00bd 0006 011e 0007 00bd 0004 03d2

Alternate Pattern

0000 006b 0000 0017 0015 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 02a3 0007 011d 0006 011e 0006 011e 0007 00bc 0007 011e

0007 00bc 0007 00be 0006 00bd 0007 00bd 0006 011e 0007 00bd 0004 03d2

0000 006b 0000 0017 0015 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 02a3 0007 011d 0006 00bd 0007 011e 0007 00bd 0006 011f

0006 00bd 0007 00bd 0006 00bd 0007 00bd 0007 011d 0007 00bd 0006 03d0

0000 006b 0000 0017 0015 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 02a3 0007 011c 0007 011e 0007 011d 0007 00bc 0007 011f

0006 00bd 0007 00bd 0007 00bd 0006 00bd 0007 011e 0006 00bd 0006 03d0

"STOP"

0000 006b 000b 0017 0015 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 02a3 0007 011d 0006 00bd 0007 011e 0006 00bd 0006 011f 0006 00bd 0007 00bc 0008 00bc 0007 00be 0006 011e 0006 011d 0007 036a 0016 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 02a3

Alternate Pattern

0000 006b 000b 0017 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7 0007 011e 0007 00be 0007 011f 0007 00bd 0007 0120

0007 00be 0007 00be 0006 00be 0007 00bf 0006 0120 0006 011f 0006 0370 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 02a7

"FIRST"

0000 006b 000b 0017 0015 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 02a3 0007 011d 0006 011e 0006 011e 0006 00bd 0007 011e 0007 011d 0007 00bc 0008 00bd 0006 00bd 0007 00bd 0006 011d 0007 036b 0015 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 02a3

Alternate Pattern

0000 006b 000b 0017 0015 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 02a3 0007 011d 0006 011e 0006 011e 0007 00bc 0007 011f 0006 011d 0007 00be 0006 00bd 0007 00bd 0006 00be 0006 011c 0007 036b 0015 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 02a3

"ALL"

0000 006b 0000 0017 0015 0013 0014 0012 0015 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 02a3 0007 011d 0006 00bd 0007 011e 0006 00bd 0007 011e

0006 011e 0007 00bd 0006 00bd 0007 00bd 0007 00bc 0007 00bd 0006 03d1

Alternate Pattern

0000 006b 0000 0017 0015 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 02a3 0007 011d 0006 011e 0006 011e 0006 00be 0006 011e

0006 011f 0006 00bd 0006 00be 0006 00bd 0007 00bd 0006 00bd 0006 03d1

0000 006b 0000 0017 0015 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 02a3 0007 011c 0007 00bd 0007 011d 0007 00be 0006 011e

0007 011e 0006 00bd 0007 00bd 0006 00bd 0007 00bd 0007 00bc 0007 03d0

0000 006b 0000 0017 0015 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 02a4 0007 011c 0007 011e 0006 011d 0007 00be 0006 011e

0006 011f 0006 00bc 0008 00bc 0007 00be 0006 00bd 0008 00bb 0007 03d0

"NEXT"

0000 006b 000b 0017 0015 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 02a3 0007 011c 0007 011e 0006 011e 0006 00bd 0007 011d 0007 011e 0007 00bd 0006 00bd 0007 00bd 0007 011e 0006 00bc 0007 036a 0016 0012 0014 0013 0014 0013 0014 0012 0015 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 02a3

Alternate Pattern

0000 006b 000b 0017 0016 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 02a3 0008 011c 0006 00be 0006 011e 0007 00bd 0006 011e 0007 011e 0006 00bd 0007 00bc 0007 00be 0006 011d 0007 00bd 0006 036b 0015 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0015 0012 0014 0013 0014 0013 0014 02a3

0000 006b 000b 0017 0015 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 02a3 0008 011c 0006 00bd 0007 011e 0007 00bd 0006 011e 0007 011e 0006 00be 0006 00bd 0007 00bc 0007 011e 0007 00bc 0006 036b 0015 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 02a3

0000 006b 000b 0017 0015 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 02a3 0007 011d 0006 011e 0006 011e 0006 00be 0006 011e 0007 011e 0006 00be 0006 00bd 0006 00be 0006 011e 0006 00bd 0006 036b 0015 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 02a3

"PROG"

0000 006b 000b 0017 0015 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 02a3 0007 011d 0006 011e 0006 011e 0007 00bc 0007 011e 0007 011e 0006 011d 0007 00be 0006 011e 0006 00be 0006 00bd 0006 0305 0015 0013 0014 0013 0014 0012 0014 0013 0014 0013 0014 0013 0014 0012 0015 0012 0014 0013 0014 0013 0014 02a3

Alternate Pattern

0000 006b 000b 0017 0016 0012 0015 0013 0014 0012 0015 0012 0015 0012 0015 0013 0014 0012 0015 0012 0015 0013 0014 0012 0015 02a7 0007 011e 0007 00bd 0008 011f 0007 00be 0006 0120 0007 011f 0006 0120 0006 00be 0007 0120 0006 00be 0007 00bd 0007 030a 0015 0013 0014 0013 0014 0012 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0013 0014 0012 0015 02a7

0000 006b 000b 0017 0015 0013 0014 0013 0015 0012 0014 0013 0014 0013 0015 0012 0015 0012 0014 0013 0015 0012 0015 0012 0014 02a7 0008 011e 0006 0120 0006 011f 0007 00bf 0006 011f

0007 0120 0006 0120 0006 00be 0007 011f 0007 00be 0007 00bc 0008 0309 0015 0013 0014 0013 0014 0013 0014 0013 0014 0013 0015 0012 0014 0013 0014 0013 0015 0012 0015 0012 0014 02a7

CONTACTS

Page 10

ADEO SCREEN Sp. z o.o.

Ul. Boleslawa Krzywoustego 31

59-500 Zlotoryja

Polska - Europe

Tel. +48 76 850 53 05

Fax + 48 76 850 53 70

Italia

Tel. +39 0461-248211

Fax +39 0461-243850

To contact Technical support: techsupport@screenresearch.com

info@adeoscreen.com

Screen Research ILT2 User And Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual