Scott VINYL ENCODER 10,DJX 100 TT User Manual

USER MANUAL

www.my-scott.com

DJX 100 TT / VINYL ENCODER 10

PROFESSIONAL USB TURNTABLE

GB-2

USER MANUAL

Vinyl Encoder 10

SAFETY INSTRUCTIONS

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all Instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacture’s
instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9. Do not try to bypass the safety purpose of the polarized plug. The wide blade is provided for your
safety. If the provided plug does not fit into your wall outlet, consult an electrician for replacement of
the obsolete outlet.

10. Prevent the power cord from being walked on or pinched particularly at plug, convenience

receptacles, and point where from the power cord is connected to the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or

sold with the apparatus. When a cart is used, exercise caution when moving the
cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of

time.

14. Refer all servicing to qualified service personnel. Serving is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled into
the apparatus or objects have fallen into it, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

15. The mains plug is used to unplug the device, so it must remain easily accessible.

WARNING

To reduce the risk of the fire or electric shock, do not expose this apparatus to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.

CAUTION

DO NOT OPEN

RISK OF ELECTRIC SHOCK

CAUTION: To reduce the risk of electric shock, do not remove any cover. No user-serviceable parts
inside.
Refer servicing to qualified service personnel only.

The lightning flash with an symbol within the equilateral triangle is intended to alert the use to the
presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.

The exclamation mark within the equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instructions in the literature accompanying this
appliance.

CAUTION

To prevent any risk of electric shock, ensure that the blades of the polarized plug can be fully inserted,
in order to prevent blade exposure.

GB-3

UNPACKING THE BOX

Before you begin assembly, please be sure all parts and accessories have arrived intact. In order to
do so, please use the check list below:

* Instruction manual * RCA cable * Slipmat * Platter
* 45rpm adaptor * Headshell * AC cord * Counterweight

Note:
* Do not connect the AC power plug before assembly has been completed.
* Before turning the power on, make sure once again that all the connections and power voltage

settings are correct.
Always turn off the power when connecting or disconnecting

* Read this manual carefully before using the unit. Be sure to store the manual in a safe place for

future reference.

* Attach a stylus cartridge to the headshell before assembling the turntable unit

.

1. Unpacking:
Carefully remove the main unit with the packaging material intact from the box. Remove the
packaging material once the unit has been removed from the shipping carton. Be sure to

identify all the accessories located in the packaging material.

2. 45 rpm adaptor
Locate and remove the 45 rpm adapter from the packaging material and place it in the cut out
designed for this purpose on the top of the main unit.

3. Turntable platter:
Remove the turntable platter from the packaging material and gently insert the platter into the
center spindle on the base of the turntable unit.

4. Drive hub:
Pull the belt to the lower side of the turntable over the drive hub.

5. Slipmat:
Remove the black slipmat from the packaging and place it on the platter.

6. Headshell:

Insert the headshell into the front end of the tone arm. While holding headshell firmly onto the front
end of the tone arm, turn the headshell locking nut counterclockwise to firmly secure the headshell
to the tone arm

.

7. Counterweight: