SCOTT SRX 210 User Manual

SXR 210

CD/MP3/WMA/SD/USB/AUX CAR RADIO

FM Stereo Radio

RDS (Radio Data System) Function

Anti-Shock Mechanism

Telephone Mute Function

4x40 W High Power Output

MODE

BAND

SCN SHF

RPT

REG

TA AF

VOL/ PUSH SEL

AMS

USER MANUAL AND INSTALLATION INSTRUCTIONS

DISP

PTY

AUX IN

CONTENTS

CONTENTS...............................................................................................................................................GB-1

ACCESSORIES........................................................................................................................................GB-2

PRECAUTION.........................................................................................................................................GB-3

INSTALLATION........................................................................................................................................GB-4

USING THE DETACHABLE FRONT PANEL .................................................................................................. GB-7

WIRING DIAGRAM.............................................................................................................................……... GB-8

OPERATIONS.......................................................................................................................................GB-9

LOCATION AND FUNCTION OF KEYS ..........................................................................................................GB-9

GENERAL OPERATIONS .......................................................................................................................... GB-10

RADIO OPERATIONS ............................................................................................................................... GB-14

RDS (RADIO DATA SYSTEM) OPERATIONS ...................................................................................……..GB-15

CD/MP3/WMA DISC OPERATIONS.........................................................................................…….............. GB-17

MIXED-MODE CD OPERATIONS................................................................................................................GB-19

SD/MMC MEMORY CARD OPERATIONS.................................................................................................... GB-

USB OPERATIONS .........................................................................................................................………. GB-

AUX IN OPERATIONS................................................................................................................................ GB-21

DISC NOTES.............................................................................................................................................GB-2

SPECIFICATIONS.......................................................................................................................GB-2

TROUBLESHOOTING..........................................................................................................................GB-2

GB-1

ACCESSORIES

Mounting Bracket

(Half Sleeve)

Tapping Screw

ISO Wire Connector

Removable Trim Ring

equipped on the unit

Screw

Hex Nut

Protective Case

Small metal Strip

Mounting Bolt

MODE

AMS VOL/ PUSHSEL

SCN SHF

BAND

Removable Control Panel

GB-2

RPT

Plain Washer

Release Key

REG

TA AF

DISP

PTY

AUXIN

Spring Washer

USB Adaptor Cable

SRX210

CD/MP3/WMA/SD/USB/AUXCARRADIO

FMStereoRadio

RDS(RadioData System) Function

Anti-ShockMechanism

TelephoneMuteFunction

4x40WHigh Power Output

MODE

SCN SHF

REG

RPT

AMS VOL/ PUSHSEL

BAND

TA AF

USERMANUALAND INSTALLATIONINSTRUCTIONS

User Manual

DISP

PTY

AUXIN

PRECAUTION

This unit is designed and manufactured with the user’s safety in mind, however any improper use or operation may result in certain dangers. It is therefore highly recommended to read this manual thoroughly and adhere to the following precautions.

SAFETY PRECAUTIONS

To prevent an electrical shock, do not open the housing of the unit. In any case of malfunctioning, only have the unit serviced

by an approved and qualified service centre. Do not expose to any water or to a very humid environment. Do not operate the unit when your hands are wet as this may cause a short circuit. For safe driving, keep the volume low in order to concentrate on traffic conditions. Do not clean the unit with alcohol, only clean with a soft dry cloth. If the unit has been kept at a high temperature or in a high humidity environment, cool down the car interior before turning on

the unit.

Do not use the unit for a long time without running the vehicle engine, it may drain the battery and the vehicle engine may not

be able to start. Before final installation in the dashboard opening, first connect the wiring and make sure the unit is working properly. Only use parts provided with the unit to ensure proper installation. Do not route wiring in places that the heat may melt the wiring insulation. When replacing the fuse, ensure that the new fuse has the capacity recommended by the manufacturer.

OPERATION PRECAUTIONS

Do not operate the player with scratched, bent or broken discs. When a disc is not loaded properly, do not force it into the disc loader. Never insert any other objects into the disc loader like a coin or pin, etc as this may cause damage or a short circuit. Do not use different disc formats other than 12cm round discs. If the unit is disconnected to the battery, it will lose memorized data. If the source disc has poor sound quality due to scratches, dirt or a bad recording, the playback sound quality may be poor.

GB-3

Installation

Notes:

- Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

- Before finally installing the unit, connect the wiring and make sure that the unit works properly.

- Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

- Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

- If installation angle exceeds 30°from horizontal, the unit may not perform properly.

- Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, hot air, or a heater, or

where it would be subject to dust, dirt or excessive vibration.

Remove the CD mechanism transit screw before installation

Before installing the unit, remove the two screws labelled “REMOVE SCREW”.

Installation Opening

This unit can be installed in any dashboard having an opening as shown below (DIN standard):

182 mm

GB-4

53 mm

Installing the unit

Be sure you test all connections first, and then follow these steps to install the unit.

1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal.

2. Disconnect the wire harness and the antenna.

3. Press the OPEN ( ) button to remove the control panel (For details, refer to ' ').

USING THE DETACHABLE FRONT PANEL

4. Lift the top of the outer trim ring then pull it out to remove it.

5. Use the two supplied release keys to remove the unit from the mounting bracket. Insert the left (“L”) and right (“R”) release keys as far as they will go (with the notches facing up) into the appropriate slots at the middle left and right sides of the unit. Then slide the sleeve off the back.

Notch

6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend out the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. To secure the sleeve in place, bend out the appropriate tabs so that they make contact with the dashboard.

7. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables.

8. If necessary, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut

(M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle's mounting area. Then use the supplied hardware (Tapping Screw (M5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This metal strap also helps ensure proper electrical grounding of the unit.

GB-5

9. Slide the unit into the sleeve until it locks into place. Ensure that you install the short part of the threading to the back of the unit and the long part to the metal strap.

10. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring and install the unit's front panel (see the steps of ' ').

TO ATTACH THE FRONT PANEL

Dismantling the unit

1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal.

2. Press the ( ) button to remove the front panel.

OPEN

3. Lift the top of the outer trim ring then pull it out to remove it.

4. Insert both of the supplied keys into the slots at the middle left and right sides of the unit then pull the unit out of the dashboard.

5. Remove the metal strap attached to the back of the unit (if attached).

GB-6

USING THE DETACHABLE FRONT PANEL

REMOVING AND PROTECTING DETACHABLE FRONT PANEL

The front panel of the unit may be removed as a theft deterrent. After removing the front panel, use the case provided to keep the front panel from getting damaged. 1 Press the OPEN button to flip down the front panel..

2 Grasp the right side of the front panel, then gently push the front panel towards the left side before pulling it out from

the unit. 3 Store the front panel in the protective case provided for safe keeping.

Fig.2Fig.1

OPEN button

Fig.4Fig.3

protective case

front panel

TO ATTACH THE FRONT PANEL

Hold the right side of the front panel with the plate facing down. First attach the left side of the front panel to the unit by inserting the hole into the left holder. Then slightly push it to the left and attach the right side hole into the right holder. Finally push up the front panel.

GB-7

Wiring Diagram

ANTENNA Socket

White RCAconnector to front left amplifier (not included)

Red RCA connector to front right amplifier(not included)

White RCAconnector to rear left amplifier (not included) output

Red RCA connector to rear right amplifier (not included)

FUSE

ISO connector: Part A: A1:

No Connect

A2:

ISO CONNECTOR

Violet torear right speaker+

Violet/Black torear right speaker-

Grey tofront right speaker+

Grey/Black tofront right speaker-

White tofront left speaker+

White/Black tofront left speaker-

GB-8

Yellowto Battery B+

BlacktoGNDB-

Red toAccessory

Blue toAntenna

Green torear left speaker+

Green/Black torear left speaker-

Orange Telephone Mute Connection Cable

No Connect

A3:

No Connect

A4:

Battery B+ (Yellow)

A5:

Antenna (Blue)

A6:

No Connect

A7:

Accessory (Red)

A8:

Ground B- (Black)

Part B: B1:

Rear Right + (Violet)

B2:

Rear Right - (Violet/Black)

B3:

FrontRight+(Grey)

B4:

Front Right - (Grey/Black)

B5:

Front Left + (White)

B6:

Front Left - (White/Black)

B7:

Rear Left + (Green)

B8:

Rear Left - (Green/Black)

+ 18 hidden pages