MODEL NO.: SBX 10
RF 2.4 GHz WIRELESS SUBWOOFER
Instruction Manual
GB- 1
PRECAUTIONS
Follow the instructions below to ensure the product is used safely and correctly.
PLACEMENT
. Do not use the unit in places which are extremely hot, cold, dusty, or humid.
. Place the unit on a flat, even surface.
. Do not restrict the airflow around the unit by placing it in a place with poor ventilation,
by covering it with a cloth, or by placing it on a carpet.
. Do not place the unit close to heat sources.
. Use the apparatus only in moderate climates.
. Do not expose the unit to rain or splash with water.
. Do not place objects filled with liquids, such as vases on the unit.
SAFETY
. When connecting and disconnecting the AC power cord, take hold of the plug and not
the cord. Pulling the cord may damage it and may be dangerous.
. The mains plug is used as the disconnect device. The plug must be easily accessible.
. When you are not going to use the unit for a long period of time, disconnect the AC
power cord from the AC mains outlet.
AC VOLTAGE
. Before use, check that the rated voltage of your unit matches your local voltage.
CONDENSATION
. When there is condensation inside the unit, it may not function normally. Unplug the
unit for 1 to 2 hours before turning the power back on, or gradually heat the room up
and dry the unit before use.
. Ensure a minimum distance of 5 cm around the unit for sufficient ventilation.
. Do not cover the ventilation openings.
BATTERIES
. Pay attention to the environmental aspects of battery disposal.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with an
arrowhead symbol within a
triangle is a warning sign
alerting the user to the
presence of “dangerous
voltage” inside the unit.
ATTENTION: To reduce the risk of
electric shock, do not remove the
cover. There are no user
serviceable parts inside the unit.
Refer all servicing to qualified
personnel.
The exclamation mark within
a triangle is a warning sign
alerting the user to the
presence of important
instructions accompanying
the product.
Congratulations on your purchase of this wireless sound system that we hope will
fully meet your requirements. It will allow you to improve the bass of your iDXS
10L or iXSW 50 system.
GB- 2
CONTENT
PRECAUTIONS 1
CONTENT 2
BOX CONTENT 2
LOCATION OF CONTROLS 2
POWER SUPPLY 2
BASIC OPERATION 2
MAINTENANCE 3
TROUBLESHOOTING GUIDE 3
TECHNICAL SPECIFICATIONS 3
BOX CONTENTS
1. Unit
2. Pin for pairing
3. Instruction manual
LOCATION OF CONTROLS
RF 2.4 GHz wireless
subwoofer
1. Bass reflex tube
2. Standby/Power LEDs
(2x)
3. Speaker
4. Bass volume control
5. PAIR button
6. Crossover frequency
switch
7. PHASE switch
8. POWER ON/OFF
switch
9. AC cord
POWER SUPPLY
Connect the AC power cord to the mains with AC 100-240V ~ 50/60Hz power
source.
BASIC OPERATION
PAIRING
Pairing is to ensure your subwoofer can receive RF transmission correctly from
the docking station.
1. You have to reset the pairing first: when the docking station is in standby mode,
use the pin (supplied) to press and hold the PAIR button of the docking
station for more than 10 seconds until the source LEDS at the top of the
docking station flash for few seconds.
2. Press the PAIR button on the docking station then the PAIR button of the
other modules within one minute. All the standby LEDs will blink rapidly until
the pairing is successful in about one minute and the source LEDS at the top
of the docking station will flash for few seconds. Then the station goes into
standby mode.
Refer to the iDXS 10L or iXSW 50 manual for more information about pairing.
2
3
4
2
5
6
7
8
9
GB- 3
Bass volume control
Rotate the bass volume dial to adjust the volume.
Crossover frequency
Slide the switch to select the crossover frequency: 80, 120 or 160 Hz for different
bass effect. This setting is depending on the music content.
Phase adjustment
As different rooms have different influences on the bass, the phase switch is
used to compensate the room acoustic effect. Place the subwoofer as required,
listen to strong bass music and then set the PHASE switch to 0° or 180°. Use the
setting which gives a stronger bass effect. This is the best phase setting for your
listening room.
MAINTENANCE
Care and maintenance
To clean the casing, unplug the unit and wipe off dust and stains with a soft,
damp cloth. Do not use benzene, thinner or similar chemicals to clean the casing.
If at any time in the future you want to dispose of this product, please
note that electrical products should not be disposed of with household
waste. Find out where your nearest recycling centre is. Consult your
local authority or retailer for more details (Waste Electrical and
Electronic Equipment Directive).
TROUBLESHOOTING GUIDE
Problems Recommendations
1. The subwoofer does
not work properly
1.1 Slide the power ON/OFF switch at ON.
1.2 Reset the unit by unplugging the AC power cord
for few seconds, then plugging it back in.
1.3 The subwoofer alone cannot be paired. If
necessary carry out a new pairing.
TECHNICAL SPECIFICATIONS
Subwoofer
Power source AC 100-240V ~ 50/60Hz
Speaker 6.5”, 4 Ohm
Output power – Speaker 50 W (r.m.s.)
Power consumption 80 W
Standby power consumption < 1 W
Dimensions 341 (H) x 220 (W) x 220 (D) mm
Weight 6 Kg
Note: Due to continuing improvements, the technical specifications are subject to
change without notice.
Loading...