Scotsman IS160 Owner’s Manual

IS160 and IS220

INTRODUCTION

This service manual is intended as a reference for
the installer, user, and service agent of this
Scotsman Ice Station. It includes the necessary
information to install, start up, operate, clean and
maintain this unit.

TABLE OF CONTENTS

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2

Installing Loose Shipped Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3

For the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4

Initial Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6

How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7

For the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8

Cleaning & Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9

Service Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11

Electrical Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12

Parts lists and wiring diagrams are located in the center of this manual, printed on yellow
paper.

This manual contains important information, read it before beginning installation or operation.
Keep it for future reference.

Safety Symbol:

Important safety information on a

hazard that might cause serious

injury.

August 1995

Page 1

IS160 and IS220

SPECIFICATIONS

The term "Ice Station" means a machine that
stores manually filled ice in an insulated, sanitary
container; upon demand it dispenses that ice into
a cup or glass.

NOTE: This ice stand is designed to dispense
cubed ice only. Flaked or Nugget ice will not

work.

IS160 SHOWN, IS220 SIMILAR,

BUT 30" WIDE.

Base
Model

IS160-1A 22" 160 lbs 115/60/1 2 amps 4’ with plug
IS220-1A 30" 220 lbs 115/60/1 2 amps 4’ with plug

Rotor motor is 1/10 H.P. *Note: Not all ice is dispensed.
Options: Push button actuation (factory installed).
Scotsman Ice Systems are designed and manufactured with the highest regard for safety and

performance. They meet or exceed the standards of U.L., and N.S.F.
Scotsman assumes no liability or responsibility of any kind for products manufactured by Scotsman that

have been altered in any way, including the use of any parts and/or other components not specifically
approved by Sc ot sman.

Scotsman reserves the right to make design changes and/or improvements at any time. Specifications and
designs are subject to change without notice.

Width Storage

Capacity*

Basic Electrical Amperage Power Cord

August 1995

Page 2

IS160 and IS220

FOR THE INSTALLER: Installation of Loose Shipped Parts

Sink:

1. Remove splash panel from unit.

2. Slip a worm drive clamp over the drain tube as
shown.

3. Hold the drip tray up at an angle of about 30

o

Slide the drain fitting into the drain tube.

DRAIN

TUBE

DRAIN

FITTING

MOUNTING

TABS

SINK

SPLASH

PANEL

Ice Lever*, Ice chute, and Fluorescent Tube

1. Slide out the ice chute mounting panel.

2. Insert the ice lever into the slot as shown.

3. Swing the lever through the slot from right to

.

left and let it hang freely.

LEVER

SLOT

4. Twist the fluorescent tube into the sockets.

5. Replace the ice chute mounting panel.

6. Insert the ice chute into the panel and twist
clockwise 1/3 turn.

7. Attach the upper front cover by pushing the
strikes on the cover into the catches on the unit.

4. Tighten the worm-drive clamp.

5. Hang the drip tray onto the mounting tabs at the
base of the unit. Replace the splash panel.

ICE CHUTE

* Optional depending upon unit configuration.

ICE CHUTE
MOUNTING

PANEL

August 1995

Page 3

IS160 and IS220

FOR THE INSTALLER

1. Locate the Ice Station on the counter.
Allow vertical clearance above unit for the
removal of the cover, and for pouring ice
into the hopper.

5

2. Plan the unit drain. Two tubes (

1

⁄4" I.D.) are required for draining.

1
Routing is either thru the back or base.
Sufficient fittings are indluded with the
unit to install in most cases.

3. In order to comply with National
Sanitation Foundation (NSF)
requirements, this unit must be either
elevated above the counter top
sufficiently to provide space for cleaning
under the unit or sealed to the counter
top.

Elevating the unit may be accomplished
by using the legs. They will screw into
threaded holes in the base of the unit.

⁄8" and

CABINET DRAIN

TUBES

August 1995

Page 4