Scotsman HD22,HD30 Product Manual

HD22 and HD30

Introduction

To the owner or user: This product manual is a
source of information about the installation, start
up, cleaning, maintenance and repair of the
product.

Table of Contents

Introduction ················································· Page 1

General Description ············································· Page 2

Specifications & Limitations ········································· Page 3

HD30 Dimensioned Illustration ······································· Page 4

HD22 Dimensioned Illustration ······································· Page 5

Product Description ············································· Page 6

Unpacking ·················································· Page 7

Installation - Plumbing ··········································· Page 8

Installation - Electrical and Ice Machine Assembly ····························· Page 9

Final Check List/Initial Start Up ······································· Page 10

Use ····················································· Page 11

General Care and Cleaning ········································· Page 12

General Care And Cleaning - Continued ·································· Page 13

Maintenance ················································ Page 14

Adjustments ················································· Page 15

Service Diagnosis ·············································· Page 16

September 2003

Page 1

HD22 and HD30

General Description

The HD22 is a hotel/motel ice dispenser. It is
designed to use a Scotsman CME306 or CME456
cube ice machine as the source for ice.

The HD30 is a wider version of the HD22 and is
designed to use a Scotsman CME256 or CME506

Ice from the cuber falls into the insulated hopper,
where it is stored until needed. When a user
pushes the dispense chute a rotating wheel scoops
the ice up to the top front of the hopper where
there is an outlet to the ice chute.

cuber as its source of ice. Additional models may
be used, see sales information for details. Flaked
or nugget ice is not recommended for use in these
dispensers.

Cuber Application Chart

Cuber Model Fits Dispenser Adapter

CME306 HD22 None Needed

CME456 HD22 None Needed

CME256* HD30 None Needed

CME506* HD30 None Needed

CME686 or CME810 HD22 KBT36

CME686 or CME810 HD30 KBT32

* Higher capacity cubers, CME656 or CME806, may also be used, but they require 230 volt power.

New dispenser / used ice machine combinations: Some of the ice machines listed in the table above
used a thermostat when on a dispenser. When re-using the ice machine on an HD22 or HD30, disconnect
and do not use the thermostat.

Prior cubers, CM250, CME250, CM500, CME500, SLC300, SLE300, SLC400, SCE400 are not compatible
with either HD22 or HD30 unless the bin thermostat is used and a thermostat bracket is installed. CM
products use bracket A32262-001, SLC/SLE products use bracket C34196202.

Basic Specifications

Model Dimensions

w”xh”xd”

with 6” leg

HD22B-1A 22 x 53 x 33 ½ 115/60/1 Basic 22” model, 60 Hz 120 lb

HD22B-6A 22 x 53 x 33 ½ 230/50/1 Basic 22” model, 50 Hz 120 lb

HD30B-1A 30 x 53 x 33 ½ 115/60/1 Basic 22” model, 60 Hz 180 lb

HD30N-1A 30 x 53 x 33 ½ 115/60/1 Coin/token model 180 lb

HD30W-1A 30 x 53 x 33 ½ 115/60/1 Water station model 180 lb

HD30B-6A 30 x 53 x 33 ½ 230/50/1 Basic 30” model, 50 Hz 180 lb

Basic Electrical

volts/hertz/phase

Model Description Bin Storage

Capacity, ARI rated

All 60 Hz models are supplied with an 11’ power cord, 50 Hz models have a 1.1 meter power cord. Basic
models dispense ice when their chute is pushed. Coin/token models require a coin or token for dispense
activation. Tokens are available from Scotsman, the part number for 500 tokens is KTOKEN. Water station
models are basic models with a separate non-refrigerated water dispense station.

September 2003

Page 2

Specifications & Limitations

HD22 and HD30

This dispenser is designed to be installed and
operated indoors, in a controlled environment.
Its minimum and maximum operating temperature
limits are the same as those for the ice machine.

Minimum Maximum

o

Air Temp 50

Voltage 60 Hz 104 126

Water Pressure* 20 psi 80 psi

* for water station model

Check the nameplate, located on the back of the
cabinet for specific information.

Scotsman reserves the right to make design
changes and/or improvements at any time.

Specifications and designs are subject to change
without notice.

Scotsman assumes no liability or responsibility of
any kind for products manufactured by Scotsman
that have been altered in any way, including the
use of any parts and/or other components not
specifically approved by Scotsman.

F 100oF

Kits:

A bin top adapter kit is also available to allow
placement of a Scotsman CME686 or CME810
Eclipse ice making head on the dispenser.

The HD22’s kit number is KBT36.

The HD30’s kit number is KBT32.

There is also a kit that can be installed on a
HD30N (coin operated model). That kit is a coin
counting timer that can be adjusted to accept more
than one quarter before activating the dispense
mechanism. The kit’s part number is 12-2909-21.

No other kits are available.

Models

There are three versions of the HD30 dispensers:
Basic, Coin/token and Water Station. The Basic
version is constructed to deliver ice when the ice
chute is pushed in, and it continues to vend ice as
long as the ice chute is held in.

The Coin/token version is designed to deliver ice
after a coin or token is inserted into the coin slot
AND then the ice chute is pushed in. Ice vending is
limited to a preset time per coin or token use.
Coins or tokens are collected in a coin box at the
bottom of the dispenser. A keyed door allows
access to the coin box without removing the front
panel.

The Water Station version is a Basic version with a
mechanical water faucet added to the left of the ice
chute. Water is dispensed whenever the faucet
lever is pushed back. The HD30 is available in all
versions, the HD22 is only available as a Basic
model.
50 Hz. The Basic models of the HD22 and HD30
are available in 230 volt 50 Hz electrical for those
countries with that type of electrical service.

September 2003

Page 3

HD22 and HD30

HD30 Dimensioned Illustration

ICE HEAD MOUNTING

451.1

17 3/4"

179.1
7"

189.4
7 1/2"

3/4 FPT
DRAIN

BACK

189.7
7 1/2"

(2) 5/16-18 UNC

24.1
1"

POWER
CORD

WATER INLET

3/8 FLARE

(WATER FILLER ONLY)

444.4

17 1/2"

254.8
10"

WATER VALVE HEIGHT
(WATER FILLER ONLY)

ICE

HEAD

762.4
30"

711.2
28"

Note: Ice fill station depth is

curved to match large ice

buckets. Listed number is

the maximum depth.

ICE FILL STATION

8 3/4 [221.5] HIEGHT

13 1/2 [342.9] WIDTH

8 1/2 [215.9] DEPTH

1351.3
53 1/4"

650.5

25 5/8"

609.6
24"

ICE

HEAD

2062.5
81 1/4"

FRONT

152.4
6"

September 2003

Page 4

849.4

33 1/2"

RIGHT SIDE

HD22 Dimensioned Illustration

(2) 5/16-18 UNC

ICE HEAD MOUNTING

24.1

POWER
CORD

1"

179.1
7"

88.9

3 1/2"

406.4
16"

3/4 FPT
DRAIN

HD22 and HD30

BACK

558.8
22"

ICE

HEAD

711.200
28"

Note: Ice fill station depth is

curved to match large ice

buckets. Listed number is

the maximum depth.

ICE FILL STATION

8 3/4 [221.5] HIEGHT

13 1/2 [342.9] WIDTH

8 1/2 [215.9] DEPTH

1351.3
53 1/4"

650.6

25 5/8"

609.6
24"

ICE

HEAD

2062.5
81 1/4"

FRONT

152.4
6"

September 2003

Page 5

850.1

33 1/2"

RIGHT SIDE