Scotsman HD150 Installation Manual
HD150
Introduction
To the owner or user: This product manual is a
source of information about the installation, start
up, cleaning, maintenance and repair of the
product.
The HD150 is a hotel/motel ice dispenser. It is
designed to use a Scotsman CME306 or CME456
ice machine as the source for ice.
Ice from the cuber falls into the insulated hopper,
where it is stored until needed. When a user
pushes the dispense button a rotating wheel
scoops the ice up to the top front of the hopper
where there is an outlet to the ice chute.
Table of Contents
Specifications/Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . page 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
Final Check List/Initial Start Up/Electrical Sequence . . . . . . . . . . . . . . . page 7
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8
Service Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9
Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . page 10
Parts lists and wiring diagrams are located in the
center of this manual, printed on yellow paper.
Note the warning symbol where it appears in this
manual. It is an alert for important safety
information on a hazard that might cause serious
injury.
Keep this manual for future reference.
This manual was printed on recycled paper.
May 2000
Page 1
Specifications:
Limitations:
•Must meet the same limitations as the cuber
installed on top of it:
550F.air minimum,
1000F.air maximum.
•Must be installed indoors.
•Must allow space to the right for air intake
when using air cooled ice machine.
•Compatible only with Scotsman CME306 or
CME456 brand models.
•Must allow space for utility connections at the
back.
•Must have a drain.
Optional Kits (for HD150-1A) Include:
Coin Mechanism, kit number KSLDC2
Key Mechanism, kit number KSLDK2
All kits are field installed.
HD150
Top View of HD150
Model Dimensions
(with legs)
W x D x H
HD150S-1A 22" x 32" x 50" 115/60/1 Stainless
Basic
Electrical
Finish Ice Storage
Steel
May 2000
Page 2
Max Fuse
Capacity
90 lb. 15 2.9
Size
Min Circuit
Ampacity
Installation: General
After the carton has been removed from the
dispenser, the legs may be installed.
Place flat portions of the carton on the floor behind
the dispenser and lay the dispenser down on its
back.
Thread the legs into the base of the dispenser. Be
sure that the legs are screwed in all the way. Turn
the leg levelers in all the way.
Move the dispenser to an upright position and set
it in the location where it will be installed. Note
where drain lines and electrical connections will be
made.
Drain:
The dispenser has a 3/4" FPT drain fitting at the
bottom center of the back panel. Connect 3/4" rigid
tubing to this connection, a vent is recommended
for most installations. Route the drain tubing to the
building drain. Follow all applicable plumbing
codes.
HD150
Note
Remove any packing material from inside the
storage bin. Retain keys for later use.
Check that gasket tape is on the top outside edge of
the dispenser where the ice machine will rest.
Because the drain tubing will be very cold,
insulation is recommenced.
Electrical:
There is an electrical junction box on the lower
back panel
Make the electrical connections there. Follow all
applicable electrical codes. Use a licensed
electrician.
The dispenser must be installed so that it is a
separate piece of equipment from the ice machine.
The drains and electrical supply must be separate.
Drain
May 2000
Page 3
Installation: Ice Machine
Check that gasket tape has been placed at the
outside edge of the dispenser top.
There is no thermostat to install. Place the ice
machine (CME306 or CME456) onto the top of the
HD150. The ice machine will sense when ice
builds up into its cube port and shut off.It
automatically restarts when that ice is removed.
Follow all instructions for installation of the ice
machine.
HD150
Drain
May 2000
Page 4
Loading...