Scotsman F1322L Installation Manual
Installation and User’s Manual for
Remote Low Side Modular Flaked and Nugget Ice
Machines
Prodigy Plus D Series Models F1222L, F1322L,
N0922L and N1322L
N0922L, N1322L, F1222L, F1522L
D Series Remote Low Side User Manual
Introduction
This ice machine is the result of years of experience
with aked and nugget ice machines. The latest in
electronics has been coupled with the time tested
Scotsman aked ice system to provide reliable ice
making and the features needed by customers.
The features include simple conductivity water level
sensing, evaporator clearing at shut down, photo-eye
sensing bin control and the ability to add options.
Contents
Installation:
Location:
Cabinet Layout
Unpacking
Water
Electrical
Refrigeration
Final Check List
Initial Start Up
Scale removal
Check Top Bearing
Bearing Service
Options
Service Diagnosis
..................................................................... Page3
....................................................................... Page4
.................................................................. Page5
...................................................................... Page6
.......................................................................... Page7
....................................................................... Page8
.................................................................... Page9
.................................................................. Page10
................................................................... Page11
................................................................... Page12
............................................................... Page13
.................................................................. Page14
........................................................................ Page15
................................................................ Page16
What to do before calling for service
.................................................. Page17
October 2014
Page 2
N0922L, N1322L, F1222L, F1522L
D Series Remote Low Side User Manual
Installation:
This machine is designed to be used indoors, in a
controlled environment. Operation outside the limits
listed here will void the warranty.
Air temperature limits
Minimum Maximum
Ice maker 50
o
F. 100oF.
Water temperature limits
Minimum Maximum
All models 40
o
F. 100oF.
Water pressure limits (potable)
Minimum Maximum
All models 20 psi 80 psi
Voltage limits
Minimum Maximum
115 volt 104 126
Most water lters remove chlorine from the water
supply to the machine which contributes to this
situation. Testing has shown that using a lter that
does not remove chlorine, such as the Scotsman
Aqua Patrol, will greatly improve this situation.
Warranty Information
The warranty statement for this product is provided
separately from this manual. Refer to it for applicable
coverage. In general warranty covers defects
in material or workmanship. It does not cover
maintenance, corrections to installations, or situations
when the machine is operated in circumstances that
exceed the limitations printed above.
Minimum conductivity (RO water)
• 10 microSiemens / CM
Water Quality (ice making circuit)
• Potable
The quality of the water supplied to the ice machine
will have an impact on the time between cleanings
and ultimately on the life of the product. Water can
contain impurities either in suspension or in solution.
Suspended solids can be ltered out. In solution
or dissolved solids cannot be ltered, they must be
diluted or treated. Water lters are recommended
to remove suspended solids. Some lters have
treatment in them for suspended solids. Check with a
water treatment service for a recommendation.
RO water. This machine can be supplied with Reverse
Osmosis water, but the water conductivity must be no
less than 10 microSiemens/cm.
Potential for Airborne Contamination
Installing an ice machine near a source of yeast
or similar material can result in the need for more
frequent sanitation cleanings due to the tendency of
these materials to contaminate the machine.
October 2014
Page 3
N0922L, N1322L, F1222L, F1522L
D Series Remote Low Side User Manual
Location:
While the machine will operate satisfactorily within the
air and water temperature limits, it will operate more
efciently when those temperatures are nearer the
lower limits. Avoid locations that are hot, dusty, greasy
or conned.
Options
The standard machine will make ice until ice lls
the bin and blocks an infrared light beam inside the
bottom of the machine. A eld installed kit is available
to adjust the ice level lower. That kit number is KVS.
The standard controller has excellent diagnostic
capabilities and communicates to the user through the
AutoAlert light panel, seen through the front panel.
There is a eld installed kit that can log data and
provide additional information when the front panel is
removed. That kit number is KSBU. A similar kit adds
network connectivity, and its number is KSB-NU.
Bin compatibility
All models are the same width: 22 inches. All models
are the same depth: 24 inches.
Dispenser compatibility
Only nugget ice models may be used with ice
dispensers. Flaked ice is not dispensable.
• ID150 – use KBT42 and KDIL-PN-150; includes
KVS, KNUGDIV and R629088514
• ID200 – use KBT43 and KNUGDIV and KVS
• ID250 – use KBT43 and KNUGDIV and KVS
See sales literature for other brand model ice and
beverage dispenser applications.
Other Bins & Applications:
Note the drop zone and ultrasonic sensor locations in
the illustrations on the next page.
Line Set
NRTE45 is a non-precharged tubing kit that contains
a 45 foot 3/8" liquid line and a 45 foot 5/8" suction
line. Tubes are supplied nitrogen charged and
capped.
Bin & adapter list:
• B322S – no adapter needed
• B330P – Use KBT27
• B530P – Use KBT27
• B530S – Use KBT27
• B842S – Use KBT39
• B948S - Use KBT38 for a single unit
• B948S – Use KBT38-2X for two units side by side
BH1100, BH1300 and BH1600 upright bins include
ller panels to accommodate a single 22 inch wide
ake or nugget ice machine. No adapter is needed.
Scotsman ice systems are designed and
manufactured with the highest regard for safety and
performance.
Scotsman assumes no liability of responsibility of
any kind for products manufactured by Scotsman
that have been altered in any way, including the use
of any part and/or other components not specically
approved by Scotsman.
Scotsman reserves the right to make design changes
and/or improvements at any time. Specications and
design are subject to change without notice.
October 2014
Page 4
N0922L, N1322L, F1222L, F1522L
D Series Remote Low Side User Manual
Cabinet Layout
21.81
55.4
18.81
47.8
13.35
1.59
4
BACK VIEW
2.63
3/4" FPT DRAIN
33.9
6.7
CONNECTION
3/8"FLARE
MACHINE
WATER INLET
3/8" O.D. REMOTE
LIQUID LINE
14.36
36.5
120 VOLT CORD
5/8" O.D. REMOTE
SUCTION
CONNECTION
16.86
42.8
LEFT SIDE VIEW
24.00
61
27.00
[68.6]
4.30
4.30
10.9
10.9
6.48
6.48
16.5
16.5
2.81
2.81
7.1
7.1
ICE DROP
OPENING
2.92
2.92
7.4
7.4
16.50
16.50
41.9
41.9
24.00
24.00
REF.
REF.
61
61
PLAN VIEW
ULTRA SONIC
BIN LEVEL
SENSOR
OPTIONAL
12.50
12.50
31.8
31.8
22.00
22.00
REF.
REF.
55.9
55.9
FRONT VIEW
22.00
55.9
22.70
57.7
October 2014
Page 5
N0922L, N1322L, F1222L, F1522L
D Series Remote Low Side User Manual
Unpacking
Remove the carton from the skid. Check for hidden
freight damage, notify the carrier immediately if any is
found. Retain the carton for the carrier’s inspection.
The machine is not bolted to the skid. If strapped
remove the strap.
Place on Bin or Dispenser
If reusing an existing bin, be sure that the bin is in
good shape and that the gasket tape on the top is not
torn up. Water leaks, not covered by warranty, could
result from a poor sealing surface. Because this is a
remote low side, a new bin is recommended due to
the high cost to the user of replacing an old bin when
a remote system is on top.
Install the correct adapter, following the directions
supplied with that adapter.
Hoist the machine onto the adapter.
Note: The machine is heavy! Use of a mechanical lift
is recommended.
Panel Removal
Position the machine on the bin or adapter. Secure
with straps from the hardware bag packed with the
machine, or those supplied with the adapter.
Remove any plastic covering the stainless steel
panels.
Remove any packaging, such as tape or foam blocks,
that may be near the gear reducer or ice chute.
Level the bin and ice machine front to back and left to
right by using the bin leg levelers.
1. Locate and loosen the two screws at the bottom
edge of the front panel.
2. Pull the front panel out at the bottom until it clears
the bin.
3. Lower the front panel down and off the machine.
4. Remove two screws at the front of the top panel.
Lift up the front of the top panel, push the top panel
back an inch, then lift to remove.
5. Locate and loosen the screw holding each side
panel to the base. Left side panel also has a screw
holding it to the control box.
6. Pull the side panel forward to release it from the
back panel.
October 2014
Page 6
Loading...