Page 1
Installation and
User's Manual for
Modular Cuber
Models C0322, C0522, C0330, C0530,
C0630, C0830 and C1030
Page 2
Introduction
C0322 through C1030
Air and Water Cooled User Manual
The design of this modular cuber is the result of
years of experience and testing. Standard features
include front accessible indicator lights and on-off
switches that provide the user with fast access to
critical information and easy operational control. .
Keep this manual for future reference.
This installation and user manual is divided into
three main sections: Installation, which provides
the trade person with the information needed to set
up and install this product; Use and Operation,
which provides the user with the information to use
the product; and Maintenance, which provides the
user with the information needed keep it operating
efficiently.
Table of Contents
Installation: Product Specifications ............................... Page 2
Model Number Description ................................... Page 3
Product Description & Electrical Requirements ......................... Page 4
C0322 and C0522 Cabinet Layout ............................... Page 5
C0330, C0530, C0630, C0830 and C1030 Cabinet Layout ................... Page 6
Water .............................................. Page 7
Panel Removal ......................................... Page 8
Plumbing Requirements ..................................... Page 9
Electrical ............................................. Page 10
Final Check List ......................................... Page 11
Initial Start Up .......................................... Page 12
Adjustments ........................................... Page 13
Use and Operation........................................ Page 14
Control Switches......................................... Page 15
Options ............................................. Page 16
Cleaning, Sanitation and Maintenance ............................. Page 17
Air cooled condenser filter .................................... Page 19
What to do before calling for service .............................. Page 20
Note any Caution or Warning symbols when they
appear on the product or in this manual. They
indicate potential hazards.
July 2006
Page 1
Page 3
C0322 through C1030
Air and Water Cooled User Manual
Installation: Product Specifications
Location Limitations:
The product is designed to be installed indoors, in
a controlled environment. Air cooled models
discharge very warm air into the room out the back.
Space must be allowed at the left side and back for
air intake and discharge. Water cooled models
discharge warm water into the building’s drain.
Space needs to be provided on both sides and
above for service access.
Space Limitations
Note: Although the machine will function, ice
capacity of air cooled machines will be significantly
reduced with minimal clearance at the sides, back
and top. Some space is recommended for service
and maintenance purposes on all models.
6" of space at the sides and back are required for
adequate operation. To get the most capacity,
locate the machine away from heat producing
appliances and heating ducts, and keep the left
side away from any wall, allow 12-18 inches of
space for good air flow
Airflow is in the left side, out the back (as viewed
from the front).
Environmental Limitations
Minimum Maximum
Air
temperature
Water
temperature
Water
pressure
o
50
F. 100oF.
o
40
F. 100oF.
20 psi 80 psi
Power supply – acceptable voltage ranges
Minimum Maximum
115 volt model 104 volts 126 volts
230 volt model 198 volts 253 volts
Warranty Information
The warranty statement for this product is provided
separately from this manual. Refer to it for
applicable coverage. In general warranty covers
defects in material or workmanship. It does not
cover maintenance, corrections to installations, or
situations when the machine is operated in
circumstances that exceed the limitations printed
above.
Air Flow
Product Information
The product is a modular cuber. That type of
machine is designed to be placed on an ice
storage bin or an ice dispenser. Many installations
only require the matching bin, but some also
require an adapter to be placed between the bin
and the cuber or between the dispenser and the
cuber. This product cannot be stacked. See the
chart for application information.
May 2007
Page 2
Page 4
Model Number Description
C0322 through C1030
Air and Water Cooled User Manual
Example:
C0322SA-1A
•
C= cuber
•
03= nominal ice capacity in 100s of pounds
•
22= nominal width of cabinet
•
S= Cube size. S=small or half dice cube.
•
M=medium or full dice cube
A=Condenser type. A=air cooled. W=water
•
cooled
-1=115 60 Hz, -32=208-230 60 Hz
•
A=Series revision code. A=first series
•
Note: Model numbers in the manual might include
only the first five characters of the model number.
Options:
There are several field-installed options that can be
installed at initial start up or later. They include:
KVS, Vari-Smart Adjustable ice level system.
•
KSB, SmartBoard Advanced feature board.
•
KPMFA223, front air flow panel. Fits C0322
•
and C0522.
•
KPMFA303, front air flow panel. Fits C0330,
C0530, C0630.
•
KPFMA309, front air flow panel. Fits C0830
and C1030.
•
A39514-021 anti-recirculation baffle. Fits
C0322, C0330, C0522, C0530, C0630.
•
A39515-021, anti-recirculation baffle. Fits
C0830 and C1030.
Some installations require bin or dispenser
adapters. See the table. Standard Bin
Applications - Adapter information.
Hotel Dispensers
The HD22 and HD30 are compatible with this ice
machine, no adapters are needed.
HD22 – use with C0322 or C0522
•
HD30 – use with C0330 or C0530
•
Note: All models ship with the On and Off switches
front accessible. If desired, the On and Off
switches can be covered but by changing the bezel
in the front panel’s trim strip. A cover-up bezel
ships loose with the machine.
Ice and Beverage Dispensers – Adapter
information
Model ID150 ID200 or ID250
C0322, C0522 KBT42 KBT43
C0530, C0630,
C0830, C1030
Does not
fit
KBT44
Other Bins & Applications:
Note the drop zone and ultrasonic sensor locations
in the illustrations on the next pages.
Scotsman ice systems are designed and
manufactured with the highest regard for safety
and performance.
Scotsman assumes no liability of responsibility of
any kind for products manufactured by Scotsman
that have been altered in any way, including the
use of any part and/or other components not
specifically approved by Scotsman.
Model
C0322,
C0522
C0530,
C0630,
C0830,
C1030
B530P,
BH360,
or B222
or B322
Direct fit KBT27
Does not
fit
B330P,
B530S,
HTB555
or
BH550
Direct fit KBT28 KBT22
BH800,
BH801,
B842S
Not
available
BH900,
B948S
Not
available
August 2006
Page 3
Scotsman reserves the right to make design
changes and/or improvements at any time.
Specifications and design are subject to change
without notice.
Page 5
C0322 through C1030
Air and Water Cooled User Manual
Product Description & Electrical Requirements
Dimensions
w"xd"xh"
22.75** x 24 x 23
30.75** x 24 x 23
Model
C0322SA-1 115/60/1 Air 12.7 15
C0322SW-1 115/60/1 Water 11.9 15
C0322SA-32 208-230/60/1 Air 6.1 15
C0322SW-32 208-320/60/1 Water 5.6 15
C0522SA-1 115/60/1 Air 13.8 15
C0522SW-1 115/60/1 Water 12.2 15
C0522SA-32 208-230/60/1 Air 7.6 15
C0522SW-32 208-230/60/1 Water 6.7 15
C0330SA-1 115/60/1 Air 12.7 15
C0330SW-1 115/60/1 Water 11.9 15
C0330SA-32 208-230/60/1 Air 6.1 15
C0330SW-32 208-230/60/1 Water 5.6 15
C0530SA-1 115/60/1 Air 13.9 15
C0530SW-1 115/60/1 Water 12.2 15
Electrical
volts/Hz/phase
Condenser
Minimum
Circuit
Ampacity
Maximum
Fuse Size*
C0530SA-32 208-230/60/1 Air 7.9 15
C0530SW-32 208-230/60/1 Water 6.7 15
C0630SA-32 208-230/60/1 Air 18.2 20
C0630SW-32 208-230/60/1 Water 17 20
C0830SA-32 208-230/60/1 Air 10.2 15
C0830SW-32 208-230/60/1 Water 9 15
C0830SA-3 208-230/60/3 Air 8.4 15
30.75** x 24 x 29
Table notes: Medium cube models have the same electrical characteristics as Small. Series revision
code omitted.
* Or HACR type circuit breakers.
** Maximum width at top panel. Air cooled models add .75" for left side louvers.
C0830SW-3 208-230/60/3 Water 7.2 15
C1030SA-32 208-230/60/1 Air 16 20
C1030SW-32 208-230/60/1 Water 14.8 15
C1030SA-3 208-230/60/3 Air 11 15
C1030SW-3 208-230/60/1 Water 9.8 15
July 2006
Page 4
Page 6
C0322 and C0522 Cabinet Layout
PLAN VIEW
22" PRODIGY
24.00 REF.
61
22.00 REF.
55.9
2.00
5.1
2.00
5.1
19.05
48.4
3.25
8.3
10.25
26
7.00
17.8
ICE DROP OPENING
ULTRASONIC
BIN LEVEL
SENSOR
(OPTIONAL)
LEFT SIDE VIEW
24.00
61
LOUVER AND
REMOVABLE FILTER
AC UNITS ONLY
AIR COOLED
BACK VIEW
1.43
3.6
1.62
4.1
3.04
7.7
10.79
27.4
14.56
37
1.60
4.1
3/8" FPT
WATER
INLET
3/4" FPT
DRAIN
.88" DIA
ELECTRICAL
ACCESS
C0322 through C1030
Air and Water Cooled User Manual
Note: Top number is centimeters, bottom number is inches.
C0322, C0522 Air Cooled Side View
Top View
July 2006
Page 5
C0322, C0522 Air Cooled Back View
Page 7
AIR COOLED
BACK VIEW
3.06
7.8
10.81
27.5
14.59
37
1.48
3.7
1.73
4.4
1.70
4.3
3/4" FPT
DRAIN
3/8" FPT
WATER
INLET
.88" DIA
ELECTRICAL
ACCESS
LEFT SIDE VIEW
24.00
61
LOUVER AND
REMOVABLE FILTER
AC UNITS ONLY
C0322 through C1030
PLAN VIEW
24.00 REF.
61
30.00 REF.
76.2
2.00
5.1
2.00
5.1
19.05
48.4
3.25
8.3
10.25
26
7.00
17.8
ICE DROP OPENING
ULTRASONIC
BIN LEVEL
SENSOR
(OPTIONAL)
LEFT SIDE VIEW
24.00
61
LOUVER AND
REMOVABLE FILTER
AC UNITS ONLY
Air and Water Cooled User Manual
C0330, C0530, C0630, C0830 and C1030 Cabinet Layout
C0330, C0530, C0630 AC Back View
Top View - All
Note: Top number is centimeters, bottom number is inches.
July 2006
C0330, C0530, C0630 Air Cooled Side View
C0830, C1030 Air Cooled Side View
Page 6
Page 8
Water
C0322 through C1030
Air and Water Cooled User Manual
The quality of the water supplied to the ice machine
will have an impact on the time between cleanings
and ultimately on the life of the product. Water can
contain impurities either in suspension or in
solution. Suspended solids can be filtered out. In
solution or dissolved solids cannot be filtered, they
must be diluted or treated. Water filters are
recommended to remove suspended solids. Some
filters have treatment in them for suspended solids.
Check with a water treatment service for a
recommendation.
RO water. This machine can be supplied with
Reverse Osmosis water, but the water conductivity
must be no less than 10 microSiemens/cm.
Potential for Airborne Contamination
Installing an ice machine near a source of yeast or
similar material can result in the need for more
frequent sanitation cleanings due to the tendency
of these materials to contaminate the machine.
Most water filters remove chlorine from the water
supply to the machine which contributes to this
situation. Testing has shown that using a filter that
does not remove chlorine, such as the Scotsman
Aqua Patrol, will greatly improve this situation,
while the ice making process itself will remove the
chlorine from the ice, resulting in no taste or odor
impact. Additionally, devices intended to enhance
ice machine sanitation, such as the Scotsman
Aqua Bullet, can be placed in the machine to keep
it cleaner between manual cleanings.
Water purge
Cube ice machines use more water than what ends
up in the bin as ice. While most water is used
during ice making, a portion is designed to be
drained out every cycle to reduce the amount of
hard water scale in the machine. That’s known as
water purge, and an effective purge can increase
the time between needed water system cleaning.
In addition, this product has the capability to
automatically vary the amount of water purged
based on the purity of the water supplied to it. The
water purge rate can also be set manually.
Adjustments of purge due to local water conditions
are not covered by warranty.
August 2006
Page 7
Page 9
C0322 through C1030
Air and Water Cooled User Manual
Panel Removal
1. Locate and loosen the two screws at the front
edge of the top panel.
2. Pull the front panel out at the top until it clears
the top panel.
3. Lift the front panel up and off the machine.
4. Remove two screws at the front of the top
panel. Lift up the front of the top panel, push
the top panel back an inch, then lift to
remove.
1. Remove
Screws
6
4
2
Dataplate
Location
5. Locate and loosen the screw holding each
side panel to the base. Left side panel also
has a screw holding it to the control box.
6. Pull the side panel forward to release it from
the back panel.
This manual covers several models. The model
number on the product is located in two places, on
the back dataplate and on the model and serial
number tag, located behind the front panel. See the
illustration for the dataplate and serial tag locations.
Write the model and serial number of this product
here:
________________________________________
Write the day, month and year of initial start up
here:
________________________________________
Switch Bezel
Serial
Plate
3
Dataplate Location and Panel Removal
Uncrate and Set Up
Begin with unpacking the ice storage bin. Remove
the carton, and using part of the carton as a
cushion, tip the bin on its back to remove the skid
and attach the legs or casters.
Return the bin to an upright position. Check the bin
top gasket for gaps and tears, fill any in with food
grade sealant prior to placing the ice machine on
the bin.
Install the bin top adapter or ice dispenser adapter,
if one is required for the application.
6
5. Remove
Screws
All models ship with the On and Off switches front
accessible. If desired, the On and Off switches can
be covered up to prevent unauthorized use by
changing the bezel in the front panel’s trim strip. A
cover-up bezel ships loose with the machine.
To change bezels: Remove the front panel, and
refer to the instruction label on the inside of the
front panel. Push snaps of standard bezel in and
pull the bezel out of the front panel trim strip.
Locate other bezel. Push into the trim strip from the
front until it snaps into place. Return the front panel
to its original position and secure it to the cabinet.
July 2006
Page 8
If the ice machine has not been unpacked, do so
now. Remove the carton from the skid. Lift the ice
machine off the skid directly onto the bin.
Note: The machine is heavy! Use a mechanical
hoist if necessary.
Secure the ice machine to the bin with the
hardware provided (two metal straps and 4 bolts).
Place the bin and ice machine in the selected
location and level it by adjusting the bin leg
levelers.
Page 10
Plumbing Requirements
Water Fitting
C0322 through C1030
Air and Water Cooled User Manual
All models require connection to cold, potable
water. A hand actuated valve within site of the
machine is required. Air cooled models have a
single 3/8” FPT inlet water connection; a 3/8” FPT
to 3/8” male flare adapter is supplied with the
machine and can be used if desired.
Inlet Water
Connection
Water cooled models have a 1/2" FPT drain fitting
plus an additional 3/8” FPT condenser inlet water
connection.
Water Filters
Drain Tubing:
Use rigid drain tubes and route them separately –
do not Tee into the bin’s drain and, if water cooled,
do not Tee the condenser drain into the reservoir
or bin drain.
Vent the reservoir drain. A vertical vent at the back
of the drain, extended about 8 - 10" will allow the
gravity drain to empty and also keep any surges
during draining from discharging water out the
vent..
Horizontal runs of drain tubing need a ¼” fall per
foot of run for proper draining.
Follow all applicable codes.
Water Cooled Shown, Air Cooled Similar
Water
Supply
Water Cooled
Supply
If connecting to water filtration, filter only the water
to the reservoir, not to the condenser. Install a new
cartridge if the filters were used with a prior
machine.
All models require drain tubing to be attached to
them. Air cooled models have a single ¾” FPT
drain fitting in the back of the cabinet. Water cooled
models have the same fitting plus an additional ½”
FPT drain fitting in the back of the cabinet.
Install new tubing when replacing a prior ice
machine, as the tubing will have been sized for the
old model and might not be correct for this one.
1. Connect water supply to water inlet fittings.
3/8" OD tubing is recommended.
Note: This NSF listed model has a 1" anti-back flow
air gap between the water inlet tube end and the
highest possible reservoir water level, no back flow
device is required for the potable water inlet.
2. Connect drain tubing to drain fittings.
3. Route the drain tubing to building drain. Follow
local codes for air gap.
Water
Cooled
Drain
Bin Drain
Connection
Potable
Water
Connection
Drain Vent
Reservoir
Drain
Connection
Floor Drain
Plumbing Connections
August 2006
Page 9
Page 11
C0322 through C1030
Ground Wire
Connection
Install
Strain
Relief
Power
Supply
Wires
Junction
Box
Cover
Air and Water Cooled User Manual
Electrical
The machine is not supplied with a power cord, one
must either be field installed or the machine
hard-wired.
The dataplate on the back of the cabinet details the
power requirements, including voltage, phase,
minimum circuit ampacity and maximum fuse size.
HACR type circuit breakers may be used in place
of fuses. Extension cords are not permitted. Use of
a licensed electrician is recommended.
Electrical connections are made inside the junction
box in the back panel of the ice machine.
1. Remove the junction box cover and route the
power cord through the access hole and
properly attach the power supply wires to the
leads in the junction box.
2. Install a field supplied strain relief per code.
Attach a ground wire to the ground connection
in the junction box.
3. Check voltage when complete.
4. Return the junction box cover to its original
position and secure with the original screws.
The electrical disconnect switch with fuse
protection must be a two pole type with a minimum
of 3 mm between open contacts.
Follow all applicable local, state and national
codes.
Electrical Connections, Back of Unit
July 2006
Page 10
Page 12
Final Check List
After connections,
1. Wash out the bin. If desired, the interior of the
bin could be sanitized.
2. Locate the ice scoop (if supplied) and have it
available for use when needed.
Final Check List:
1. Is the unit located indoors in a controlled
environment?
2. Is the unit located where it can receive
adequate cooling air?
3. Has the correct electrical power been supplied
to the machine?
C0322 through C1030
Air and Water Cooled User Manual
4. Have all the water supply connections been
made?
5. Have all the drain connections been made?
6. Has the unit been leveled?
7. Have all unpacking materials and tape been
removed?
8. Is the correct switch bezel installed in the trim
strip?
9. Is the water pressure adequate?
10. Have the drain connections been checked for
leaks?
11. Has the bin interior been wiped clean or
sanitized?
12. Have any water filter cartridges been replaced?
13. Have all required kits and adapters been
properly installed?
July 2006
Page 11
Page 13
C0322 through C1030
Air and Water Cooled User Manual
Initial Start Up
1. Remove front panel. Check machine for any
packing or wires rubbing moving parts. Note
location of control board in upper left corner of
the machine’s front.
2. Remove tape securing curtain to evaporator.
3. Switch on the electrical power to the machine.
Observe that some of the control’s indicator
lights glow and its display shows O.
4. Open the water supply valve.
5. Push and release the ON button. The code
display will begin to blink F.
The purge valve opens, the water pump starts and
the inlet water valve opens to add water to the
reservoir. In a few seconds the purge valve closes
and the water pump stops. Water will flow into the
machine until the reservoir is full. The hot gas valve
and harvest assist device will activate, then the
compressor and water pump will start. If it’s an air
cooled model the fan(s) motors will begin to turn a
few moments after the compressor starts. The
display will show a continuous F. Five seconds later
the hot gas valve will close and the harvest assist
device will return to its standby position. Warm air
will be discharged from air cooled models.
6. Observe the Ready for Harvest indicator light.
It may blink early in the cycle, that is normal.
The control will ignore that signal for the first 6
minutes of freeze.
seconds the purge valve closes but the inlet water
valve continues to fill the reservoir. Harvest
continues until the ice is released as a unit and
forces the curtain to open. When the curtain opens
it signals the controller which returns the unit to a
freeze cycle.
9. Check the ice harvested for proper bridge
thickness. The ice bridge is factory set at 1/8
inch. If needed, adjust bridge thickness. Do
NOT make it too thin.
10. Return the front panel to its normal position
and secure it to the machine.
11. Instruct the user in the operation of the
machine and its maintenance requirements.
12. Fill out and mail the warranty registration form.
Typical Ice Making Cycle Times (minutes).
Listed times are for clean machines in proper
installations. Cycle length at startup will be longer
until the system stabilizes.
Model
70
50
o
o
F air /
F. water
90
70
o
o
F. air /
F. water
C0322A 10-12 14-16
C0322W 9-11 10-12
7. During the Freeze cycle move the curtain and
observe that the SW1 or SW2 light on the
control board blinks On when the curtain
moves away from the evaporator and Off when
returned to its normal position.
Note: Moving the curtain during the Freeze cycle
has no affect on control function, but will cause
water to flow into the cube chute.
8. When enough ice has frozen, the Ready for
Harvest indicator light will be on steady. After
it’s been on steady for a few seconds Harvest
will begin.
The display shows an H. The hot gas valve opens,
the air cooled fan motor(s) shut off and the harvest
assist mechanism is activated. The purge valve
opens to drain some water, when it does the inlet
water valve opens to refill the reservoir. After a few
July 2006
Page 12
C0522A 11-13 16-18
C0522W 13-15 13-15
C0330A 9-11 12-14
C0330W 8-10 9-11
C0530A 12-14 16-18
C0530W 10-12 11-13
C0630A 9-11 11-13
C0630W 7-9 10-12
C0830A 10-12 13-15
C0830W 11-13 12-14
C1030A 9-11 11-13
C1030W 9-11 10-12
Page 14
Adjustments
C0322 through C1030
Air and Water Cooled User Manual
Bridge Thickness - For the Service Tech Only
1. Push and hold Off till the machine stops.
2. Remove evaporator cover.
3. Remove curtain.
4. Use a hex wrench and rotate the bridge
thickness adjustment screw in 1/8 turn
increments CW to increase bridge thickness.
Rotate CCW to decrease bridge thickness.
Caution: Do not make the bridge too thin or the
machine will not harvest properly. Bridge thickness
adjustments are not covered by warranty.
5. Return curtain and evaporator cover to their
normal positions.
6. Push and release the On button. Check next
harvest of ice. Repeat steps 1-6 if needed.
Note: Indentations may be deeper on C0322 and C0330
1/8-3/16"
bridge
Too Big
Just Right
Too Small
Ice Bridge Thickness Measurement
Adjustment
Screw
Water Purge Setting
The water purge is factory set to the automatic
position, suitable for most water conditions. The
setting can be changed to one of 5 manual settings
or left on automatic.
Purge
setting
Water
Type
1 - Minimum
RO water or
equivalent
2Moderate
Low TDS
non-RO
water
3Standard
Use for
typical
water
To set:
1. Switch the machine OFF by holding the Off
button in until a number or the letter A shows
on the display.
2. Press and release the On button repeatedly
until the number on the display corresponds to
the desired setting.
Bridge Thickness Adjustment Mechanism
4 - Heavy 5 - Maximum A - Automatic
Any with
High TDS
water
Very High
TDS water
conductivity not
less than 10
microSiemens/cm
Note: Water cooled models, the refrigeration
system discharge pressure is factory set at 245
PSIG, which should yield a freeze cycle discharge
water temperature of about 105-110 degrees F.
Adjust if necessary.
3. Press and release the Off switch again to
return to the normal control state.
July 2006
Page 13
Page 15
C0322 through C1030
Air and Water Cooled User Manual
Use and Operation
Once started, the ice machine will automatically
make ice until the bin or dispenser is full of ice.
When ice level drops, the ice machine will resume
making ice.
Caution: Do not place anything on top of the ice
machine, including the ice scoop. Debris and
moisture from objects on top of the machine can
work their way into the cabinet and cause serious
damage. Damage caused by foreign material is not
covered by warranty.
There are four indicator lights at the front of the
machine that provide information on the condition
of the machine.
Indicator Lights:
Power
•
Status
•
Water
•
De-scale & Sanitize
•
Indicator Lights & Their Meanings
Power Status Water De-Scale & Sanitize
Steady Green Normal Normal – bin full or making ice - -
Blinking Green
Blinking Red -
Yellow - - -
Blinking
Yellow
Light off No power Switched off Normal Normal
All Blinking Unit remotely locked out – check with leasing company
Self Test
Failure
- - - In Cleaning mode
Switching on or off - -
Diagnostic shutdown or, if making
ice, temperature sensor failure
Lack of
water
-
Time to de-scale and
sanitize
If the Water light is on, the machine has sensed a
lack of water. Check the water supply to the
machine. The water could have been shut off or the
water filter cartridges might need to be changed.
If the De-Scale light is on, the machine has
determined that it needs to be cleaned. Contact an
authorized Scotsman service agent and have the
machine cleaned, de-scaled and sanitized.
July 2006
Page 14
Note: A Component Indicator Light switches ON to
indicate that the component is operating.
Note: There are two Curtain Switch lights, SW1 and
SW2. These single plate models have one curtain
switch light on all the time, as a curtain switch light
is ON when a curtain is either open or not present.
Page 16
Control Switches
02-4294-01 Rev.A.
Adjust Ice Level
L
o
w
e
r
Bin
Full
C0322 through C1030
Air and Water Cooled User Manual
There is front access to two switches – On and Off.
Status De-Scale Off
Power Water On
To switch the machine OFF, push and release the
Off button. The machine will shut off at the end of
the next cycle. To shut the machine off
immediately, push and hold the Off button for 3
seconds.
To switch the machine ON, push and release the
On button. The machine will go through a start up
process and then resume ice making.
Control Options
There are three optional, field installed controls
that can be added to this machine.
•
VariSmart™ adjustable ice level control
•
SmartBoard™ advanced control board and
data logger
Adjustable ice level control, kit # KVS
When this option is present there is an adjustment
post and an additional indicator light to the right of
the four indicator lights mentioned above. The
ultrasonic ice level control allows the user to control
the point that the ice machine will stop making ice
before the bin or dispenser is full. Reasons for this
include:
Seasonal changes in ice used
•
Planning to sanitize the bin
•
Faster turnover for fresher ice
•
Certain dispenser applications where
•
maximum ice level is not desired
Use of control
VariSmart Control Area
There are several positions the ice level can be set
to, including Off (knob and label indicators lined
up), where it fills the bin until the standard bin
control shuts the machine off. See the kit’s
instructions for complete details.
Rotate the adjustment post to the desired ice level.
The machine will fill up to that level and when it
shuts off the indicator light next to the adjustment
post will be On.
Note: Ice will build up in the bin or dispenser at an
angle, the distance set will be from the sensor to
the top of the ice. The sensor position is shown in
the cabinet layout diagrams.
The actual distance between the highest point of
the ice may be closer or further away than the
distance set, depending upon the angle of the ice.
July 2006
Page 15
Page 17
C0322 through C1030
SmartBoard Advanced Feature Control™
See Instructions for Available Features
34
SEL
02-4293-01 Rev A.
ENTER
ESC
Air and Water Cooled User Manual
Options
Advanced Feature Board, kit #KSB
When this option is present there is an additional
display panel in the area below the main control
board. It is not visible when the front panel is on.
The Smart-Board’s features include:
Seven day programmable ice level setting
•
when used with the optional Ultrasonic ice
level control
Recording of machine operation, including
•
cycle time.
Calculation of average cycle time
•
Recall of malfunctions with the time they
•
occurred.
Ice
The cuber drops ice in large sections. That ice will
break up into random parts as it falls into the bin,
but some large sections may remain on top of the
ice in the bin. When removing ice, tap the groups of
ice with an ice scoop to separate them into smaller
units. In a dispenser, this ice will break up into
mostly individual cubes as the dispense
mechanism moves the ice.
The ice in the bin will slope down from the right to
the left. This is normal.
Heat
Air cooled models will generate heat when in
operation. That heat is discharged out the back of
the cabinet.
Noise
The ice machine will make noise when it is in ice
making mode. The compressor, fan motor(s) if air
cooled and water pump all produce some sound. It
is also normal to hear some cracking just before
the harvest cycle begins. In addition, during the
harvest cycle the harvest assist solenoid will click
twice as it pushes the ice out and returns to its
normal position. The ice harvests as a unit or slab,
which makes some noise when it impacts the bin or
dispenser. These noises are all normal for this
machine.
July 2006
Page 16
Page 18
C0322 through C1030
Air and Water Cooled User Manual
Cleaning, Sanitation and Maintenance
This ice system requires three types of
maintenance:
Remove the build up of mineral scale from the ice machine’s water system and sensors.
•
Sanitize the ice machine’s water system and the ice storage bin or dispenser.
•
Clean or replace the air filter and clean the air cooled condenser (air cooled models only).
•
It is the User’s responsibility to keep the ice machine and ice storage bin in a sanitary condition. Without
human intervention, sanitation will not be maintained. Ice machines also require occasional cleaning of
their water systems with a specifically designed chemical. This chemical dissolves mineral build up that
forms during the ice making process.
Sanitize the ice storage bin as frequently as local health codes require, and every time the ice machine
is cleaned and sanitized.
The ice machine’s water system should be cleaned and sanitized a minimum of twice per year.
1. Remove the front panel.
2. Remove the evaporator cover.
3. If the machine is operating, push and release
the Harvest button. When the machine
completes the Harvest cycle it will stop. If the
bin is full (b shows in display) push and release
the Off button.
4. Remove all ice from the storage bin or
dispenser.
5. Push and release the Clean button. The yellow
Clean light will blink and the display will show
C. The machine will drain the reservoir and refill
it. Go onto the next step when the reservoir has
filled.
6. Pour 8 ounces of Scotsman Clear 1 ice
machine scale remover into the reservoir.
7. Allow the ice machine scale remover to
circulate in the water system for at least 10
minutes.
8. Push and release the Clean button again. The
yellow Clean light will be on continuously and
the machine will drain and refill the reservoir
repeatedly to purge out the ice machine scale
remover and residue.
9. Allow the drain and refill process to continue for
at least 20 minutes.
10. Push and release the Off button. The clean
cycle will stop and the display will show O.
Note: If unit has not been de-scaled for an
extended period of time and significant mineral
scale remains, repeat steps 5-10.
11. Mix a cleaning solution of 1 oz of ice machine
scale remover to 12 ounces of water.
12. Locate curtain, push in on edge of curtain by
pivot pin to release it. Pull curtain out of
machine.
Push Here
Ice machine cleaner contains
acids. Acids can cause burns.
If concentrated cleaner
comes in contact with skin,
flush with water. If swallowed,
do NOT induce vomiting.
Give large amounts of water
or milk. Call Physician
immediately. Keep out of the
reach of children.
July 2006
Page 17
Pull Here
Page 19
C0322 through C1030
Inspect Orifice Holes
Air and Water Cooled User Manual
13. Remove water distributor from ice machine.
Inspect distributor for restricted orifice holes.
Be sure all holes are fully open.
Squeeze Tabs Together, Slide Out Until it Stops,
Then Lift to Remove
Remove Water Distributor
18. Wash all interior surfaces of the freezing
compartment, including evaporator cover and
right side panel liner with the sanitizer solution.
19. Return water level sensor, ice thickness
sensor, water distributor and curtain to their
normal positions.
20. Push and hold the clean button to drain the
reservoir. Push and release the clean button
again and when the purge valve indicator light
goes out, immediately pour the remaining
cleaning solution into the reservoir.
21. Circulate the sanitizer solution for 10 minutes,
then push and release the Clean button.
22. Allow the water system to be flushed of
sanitizer for at least 20 minutes, then push and
release the Off button.
23. Return the evaporator cover and front panel to
their normal position and secure with the
original fasteners.
Inspect Water Distributor
Locate ice thickness sensor. Squeeze
14.
mounting legs together to release sensor.
Wash the metal surfaces of the sensor and the
adjustment screw with ice machine scale
remover solution. Also wash the water
distributor and curtain with the ice machine
cleaner solution.
15. Locate water level sensor. Squeeze catches
together and pull up to remove sensor. Wash
metal surfaces of sensor with ice machine
scale remover solution.
16. Mix a solution of sanitizer.
Note: A possible sanitizing solution may be made
by mixing 1 ounce of liquid household bleach with 2
gallons of warm (95-115
o
F.) potable water.
24. Push and release the On button to resume ice
making.
Ice Storage Bin
1. Remove and discard all ice.
2. Mix a solution of 7 ounces of Scotsman Clear 1
ice machine scale remover in 84 ounces of
potable water and wash all interior surfaces of
the ice storage bin to remove any mineral scale
build up. Pour excess cleaner solution into the
bin’s drain.
3. Mix a solution of sanitizer and thoroughly wash
all interior surfaces of the ice storage bin. Pour
excess sanitizer solution into the bin’s drain.
17. Thoroughly wash all surfaces of the ice
thickness sensor, water level sensor, curtain
and water distributor with the sanitizer solution.
July 2006
Page 18
Page 20
Air cooled condenser filter
1. Pull air filter(s) forward from side panel.
C0322 through C1030
Air and Water Cooled User Manual
Air Filter
2. Wash the dust and grease off the filter.
3. Return it to its original position.
Do not operate the machine without the filter in
place except during cleaning.
Air cooled condenser
If the machine has been operated without a filter
the air cooled condenser fins will need to be
cleaned.
They are located under the fan blades. The
services of a refrigeration technician will be
required to clean the condenser.
Exterior Panels
The front and side panels are durable stainless
steel. Fingerprints, dust and grease will require
cleaning with a good quality stainless steel cleaner.
Water filters
If the machine has been connected to water filters,
check the cartridges for the date they were
replaced or for the pressure on the gauge. Change
cartridges if they’ve been installed more than 6
months or if the pressure drops too much when the
ice machine fills with water.
July 2006
Page 19
Page 21
C0322 through C1030
Air and Water Cooled User Manual
What to do before calling for service
Reasons the machine might shut itself off:
Lack of water.
•
Freeze cycle takes too long.
•
Harvest cycle takes too long.
•
High discharge temperature.
•
Controller self test failure.
•
Check the following:
1. Has the water supply to the ice machine or
building been shut off? If yes, the ice machine will
automatically restart within 25 minutes after water
begins to flow to it.
2. Has power been shut off to the ice machine? If
yes, the ice machine will automatically restart when
power is restored.
Curtain
3. Has someone shut the water off to a water
cooled unit? If yes, after the water supply has been
restored the ice machine may need to be manually
reset.
4. Is the curtain open because some ice is stuck
under it? If so, remove the ice and the machine
should start in a few minutes.
Note: Curtain can be removed & replaced anytime
the machine is in a standby mode or when it is in a
freeze cycle. However, removal of the curtain
during freeze will result in water flowing into the
bin. Removal of the curtain during harvest
terminates harvest at that point and, if left off, will
result in the machine shutting off.
To Manually Reset the machine.
•
Push and release the Off button.
•
Push and release the On button.
Clear Ice
From Here
Clear ice From Beneath Curtain
To Shut the Machine Off:
1. Push and hold the Off button for 3 seconds or
until the machine stops.
Reset or Switch Off
July 2006
Page 20
Page 22
SCOTSMAN ICE SYSTEMS
775 Corporate Woods Parkway, Vernon Hills, IL 60061
800-533-6006
www.scotsman-ice.com
17-3083-01
Loading...