Page 1
USER’S GUIDE
SC2W900FMR
SC2W900FMR-2
FCC ID : O44J2W907R
Scosche Industries, Inc.
nd
SC2W900FMR
SC2W900FMR-2
U
S
E
R
FCC ID : O44J2W907R
This device complies with Part 15 of the FCC Rules.
O
peration is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
CAUTION : Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate this dev
Scosche Industries, Inc.
/
nd
’S
ice.
Two-Way FM Remote
G
UID
E
Page 2
TABLE OF CONTENTS
1. Safety Information
2. Remote-Pager : SC2W900FMR, SC2W900FMR
3. Description of Remote Appearance
4. ScoscheGLO Color LCD
5. LCD Icons
6. Remote-Pager Button Functions
7. More Button Functions
8. Remote-Pager Learn Routine
9.
Auto-Start Function
10. Reservation Mode Page 10
11. Canceling Reservation Mode Page 11
12. Valet Mode
13. Safety Shut Down Features
14. Turbo Mode
15. 2ndcar Mode
-2
nd
w/LCD
Page 4
Page 4
Page 5
Page 5
Page 6
Page 7
Page 8
Page 9
Page 9
Page 12
Page 12
Page 12
Page 12
Page 2 Page 3
Page 3
Safety Information
Please take these safety precautions under the following conditions:
1. Servicing the vehicle
When servicing (i.e. changing the oil, washing your car) your automobile, the
Scosche system should be in Valet Mode. There is a safety shutdown switch
under the hood that deactivates the remote starter function if the hood is open.
However, if the switch has been damaged or the switch has been installed
improperly, the vehicle may start when Button
the hood is open.
2. Loaning your vehicle to others
Whenever you loan your vehicle to an individual who is not familiar with Scosche,
please put the vehicle in Valet mode. This will prevent the vehicle loaner from
accidentally activating the Scosche auto-security system.
3. For manual transmission vehicles
I
f the
Scosche
precautions are required because the
system is installed in a manual transmissi
Scosche
I I
is pressed for 2 seconds even if
on vehicle, extra
does not monitor the gear shifter :
Description of Remote Appearance
Front Side
Rear
I m p o r t a n t !
w
hen a door or hatchback opens. Please verify that the opening of any door o
hatchback cancels Reservation Mode. If any of the doors or hatchback are not
monitored by
do not use the
D
o not set Reservation Mode if the window(s) are open or if there is
the vehicle, this includes animals. Remote start installation in a manual transmission
vehicle with a convertible top is not recommended.
Remote-Pager : SC2W900FMR/ SC2W900FMR-
The model name, SC2W900FMR, SC2W900FMR -2
FrequencyModulation Remote with Liquid Crystal Display
This transmitter allows you to activate multiple functions by pressing different
combinations of the 4 buttons on the unit.
Scosche
Scosche
U
nder normal circumstances, Reservation Mode is cancelled
r
because of improper installation or a faulty dome light switch,
and take your vehicle immediately to the dealer for repair.
anyone insi
nd
2
w/LCD
nd
stands for
.
Page 4 Page 5
Two Way 900MHz
de
ScoscheGLO Color LCD
The remote-pager comes with Scosche LCD which is a unique color LCD display
that visually tells you the security status of your vehicle as long as you are in range.
There are differing icons that will appear on your Scosche LCD indicating what
your vehicle is currently doing.
SC2W900FMR
SC2W900FMR-2
nd
Page 4
LCD Icons
Icon
Explanation
Indicates that Timer Mode is on.
Indicates that Turbo Mode is on. ( SC2W900FMR )
Indicates that Passive Arming Mode is on.
Icon
Explanation
Indicates that your vehicle has auto-started properly or that
the ignition is on.
Indicates that your Hood is open.
Indicates that your trunk is open.
Indicates that 2ndVehicle Mode is on.( SC2W900FMR-2nd)
Indicates that the Shock Sensor has been triggered.
Indicates that the Shock sensor is turned off.
Indicates that you are in Valet Mode.
Indicates that your parking lights are flashing.
Indicates that your siren is turned on when locking or
unlocking your vehicle.
Indicates that the RPS is on.
Indicates that someone is paging you from your vehicle.
Indicates that your remote-pager is transmitting signals to
the controller unit.
Indicates that Vibration Mode is on.
Indicates that your car is locked or unlocked.
Displays remaining battery life.
1. Time Clock.
2. Remainder of the engine running time.
Indicates that your door is open.
Remote-Pager Button Functions
Button(s)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Note : " "
"
( )"Represents simultaneously pressing the buttons.
"
( )"Represents simultaneously pressing the buttons for 2 seconds.
I
I I
I I I
I V
II-
IIII V -
( I + I I )
( I + I I I )
( I I + I I I )
( I I + I V )
( I I I + I V )
(I+III) -
(I+II) ( I + I V ) -
Represents pressing the button for 2 seconds.
Pressed
For
1/2 sec
1/2 sec
1/2 sec
1/2 sec
2 sec
2 sec
2 sec
1/2 sec
1/2 sec
1/2 sec
1/2 sec
1/2 sec
2 sec
2 sec
2 sec
Function
Lock / Arm
Unlock / Disarm
AUX 1
AUX 2
Query Function
Auto-start Function – on/off
Trunk Release
Panic, Press Ito turn off the siren.
Siren Chirp – on/off
Valet Mode – on/off
Passive Arming – on/off
Timer Start Mode – on/off
Turbo Mode - on/off
2ndCar - on/off (SC2W900FMR-2nd)
Shock Sensor – on/off
Programming Menu 1
Programming Menu 2
(SC2W900FMR)
Page 6
Page 7
Page 5
More Button Functions
Remote-Pager Learn Routine
(1) T
ime Setting
STEP 1
STEP 2
STEP 3
STEP 4
(2) RPS & V
ibration mode on or off
STEP 1
STEP 2
Button
(I I+I I I) -
(I)
(I)
(I I)
(I I+I I I) -
Button
(I I+I I I) -
(I I I)
PressedFor
2 sec
1/2 sec
1/2 sec
1/2 sec
2 sec
PressedFor
2 sec
1/2 sec
Function
Tones will sound for confirmation
Time setting is on. The numbers will
flash, and tones will sound.
Change hour.
Change minutes.
Time setting is off. Tones will
sound.
Function
Tones will sound for confirmation
RPS on or off, tones will sound for
confirmation.
The Scosche system will allow up to three remotes to be programmed to one
vehicle. Please perform the following procedure to add or reprogram additional
remotes.
Step1 :
Step2 :
transmitter has been programmed. You can continue programming additional remotes.
The parking lights will flash two times when the programming mode has expired.
Activate Valet/Programming mode by manually turning the ignition
on and off five times
with the key within a 7 second period.
The parking light will flash once with successful
completion of this step.
Within a 7 second period after cycling the ignition for the 5
press button I. The parking lights will flash once to confirm that the
(between Acc and On)
t h
time,
Auto-Start Function
Press button
Remember, that a key in the ignition is required to drive the car.
For manual transmission vehicles, please use reservation mode.
Press button
The engine will run 15 or 25 minutes (25 or 45 min for diesel) depending on preset
options at the time of installation and then shut off.
II
for 2 seconds to auto-start an automatic transmission engine.
I I
for 2 seconds in order to turn off an auto-started car.
Note :
(I V)
1/2 sec
Vibration mode on or off, tones will
sound for confirmation.
Step 2 must be completed within 15 seconds. If not, start over at
step 1.
Page 8
-
shows the amount of run-time left in the remote
start mode.
A n t i - G r i n d
The anti-grind circuit (an optional feature provided by your installer) prevents you
from engaging the starter on a remote-started vehicle.
Page 9
Page 6
Diagnosing problems with Auto-Start
If there is a problem in auto-starting your vehicle,the Scosche system will do one of
two things; if it fails for any of the reasons listed in the table below, it will flash the
parkinglights three times then flash the error number. Otherwise, it will attempt to
start the vehicle three times. If, after three times, the vehicle will not start or stay
running, the Scosche system will shut down. In either case, please see your
installer to resolve the situation.
Error Number
(# of times parking lights flash)
1
2
3
4
5
6
7
Reservation Mode
Reservation Off (Manual Transmission Only)
(manual transmission only)
Error Reason
Engine On
Key On
Door Open
Trunk Open
Brake On
Hood Open
In order to auto-start your manual transmission vehicle, you must first set the
Scosche system to Reservation Mode before leaving your vehicle. The purpose
of Reservation Mode is to leave the transmission gear in the neutral position when
you leave your vehicle. Reservation mode is intended for use on MANUAL
TRANSMISSIONS ONLY and NOT FOR AUTOMATIC TRANSMISSIONS.
Reservation Mode must be engaged each and every time you leave your manual
transmission vehicle in order to auto-start it.
Note :
The system is not recommended for vehicles with removable tops.
Important requirements to activate Reservation Mode
- The transmission must be in the NEUTRAL position.
- The vehicle windows must be rolled up.
- Do not set the reservation mode with people in the vehicle.
- Do not auto-start the vehicle with people in the it.
Activating Reservation Mode
Step1 :
Step2 :
Step3 :
Step4 :
Step5 :
After arriving at your destination, and BEFORE TURNING
YOUR ENGINE OFF, place the transmission in the Neutral position.
Activate the parking brake.
Remove your foot from the foot brake.
Remove the key from the ignition, and the engine will remain running.
Exit the vehicle and close the door within two minutes after
a c t i v a t i n gthe parking brake. The engine will shut off and reservation
mode for the remote-starter is now complete.
(Manual Transmission only)
Your vehicle is now ready for auto-starting. However, the reservation mode will
be cancelled if a door is opened or the Scosche system is put in Valet mode
after the reservation has been set. Once cancelled, you will have to start the
vehicle with the key and repeat the above 5 steps if you want to restore reservation
mode.
Important!
When the vehicle shuts off after reservation mode, the
Scosche system will lock/arm the vehicle. Take care to not lock your keys inside.
Important!
If you try to auto-start the vehicle when reservation mode
has not been set, the auto-start feature will not work.
When you press the auto-start button, the remote will beep three times.
The car parking lights will flash three times, pause, then flash seven times.
Canceling Reservation Mode
If you do not want to set reservation mode, shut off the engine before you exit the
vehicle. The engine will shut off for the following reasons:
- You did not activate the parking brake or pressed the foot brake when you
turned the key to the off position.
- You released the parking brake while the engine was running.
- You entered Valet Mode after the Reservation Mode has been completed.
Page 10
Page 11
Page 7
Valet Mode
While the vehicle is in valet mode, only the keyless entry function will be available.
Valet Mode is very useful when loaning your vehicle or having it serviced.
In order to enter Valet mode, press buttons
In order to manually enter Valet Mode, insert your key into the ignition and turn
the ignition on, then off,
(between ACC and ON)
You can exit Valet Mode only by pressing buttons
( I + I I I )
simultaneously for a 1/2 second.
( I + I I I )
simultaneously for a 1/2 second.
five times within 10 seconds.
Safety Shut Down Features
The Scosche SC2W900FMR, SC2W900FMR-2ndsystem has several shut down
safety features. The following actions will shut down the engine or prevent the car
from auto-starting : Opening the hood, pressing the brake, or if Valet Mode is turned on.
(
Turbo Mode
If this optional Turbo Mode has been programmed at the time of installation,
you can turn this feature on and off by pressing buttons
In this mode, if the emergency brake has been set, the engine will continue to run
after the key has been taken out of the ignition. It will run until two minutes after the
emergency brake has been set.
• To utilize this mode, the emergency brake sensing wire has to be connected to the
emergency brake wire of the vehicle. Consult the authorized dealer for this mode.
• This option is ideal for turbo-charged vehicles because it allows the turbo too
slowly cool after operation.
SC2W900FMR
)
( I I I + I V )
for a 1/2 second.
nd
2
Car Mode
This Remote-Pager is able to operate a 2ndvehicle.
Press buttons
Car, the Remote-Pager will not communicate with the 1stvehicle. To Exit 2ndCar
press buttons
III&IV
simultaneously for 1/2 second. If this mode is turned to 2
I I I & I V
simultaneously again.
(
SC2W900FMR-2
Page 12
nd
)
nd
Page 13
Page 8
Page 14 Page 15
Loading...