Scosche DDR-VW01 Installation Instructions Manual

DDR-VW01

2007-UP

VOLKSWAGEN

DATA & DISPLAY RETENTION INTERFACE

The Scosche DDR-VW01 allows vehicle information such as climate

control, parking sensors and heated seats to be displayed on any aftermarket head unit with rear camera input. The DDR-VW01 will also retain steering wheel controls. Extensive vehicle settings can

also be adjusted from the steering wheel controls.

RETAINS:

• Climate Control Visual Display

• Park Assist Visual Display

• All Factory Amplifiers

• Amplifier Settings Menu

• Steering Wheel Controls

OUTPUTS:

• Data Driven +12V

Accessory

(R.A.P.)

• Illumination

• Vehicle Speed Sense

• Parking Brake

• Reverse

2009-13 CC

2009-13 Golf/GTI (MKVI)

2006-09 Golf/GTI (MKV)

2011-13 Jetta/GTI (MKVI)

Requires aftermarket AV/AVN head unit with rear camera input and reverse trigger.

WORKS WITH:

2006-10 Jetta/GTI (MKV)

2011-13 Passat (B7)

2006-10 Passat (B6)

2009-13 Tiguan

1.2.

3. Match and connect the ap opriate wires from the DDR-VW01 harness to the appropriate wires of the plug provided with your aftermarket stereo. for example, connect the +12V “yellow” constant lead from your stereo to the “yellow” wire on the DDR-VW01 harness. The color code are designed to match most brands of aftermarket car stereo.

5. ape all unused wires to prevent wires from short circuiting.

6. Reconnect Negative battery cabl

7. Set the DIP switches acc ding to instructions on top of page 3.

8. Set steering wheel con ols according to the diagram at the bottom of page 3.

10.

Make all connections to the DDR-VW01 including the chi

speaker, prepared steering wheel control harness, power harness, and video RCA. (If used, plug aftermarket reverse camera to female RCA connector.)

Make all connections to your aftermarket stereo including the power and speaker harness, video input RCA, and steering wheel control jack or wire.

11.1. Make connection to your vehicles factory s eo harness.

12.2. As you install your new s eo, place the DDR-VW01 module in the

rear or to the side of the dash cavity out of the way of the stereo.

INSTALLATION

Disconnect the Negative battery cable om the battery to avoid short circuits.

Remove and unplug factory stereo.

WIRE COLOR CODES

The color codes used in this car stereo connector conform to the standards set by the E.I.A. (Electronics Industry Association). They may differ from the wiring codes found on your specific car stereo. Always refer to your stereo owner’s manual for wiring details about your specific car stereo. Be sure to insulate unused wires from each other and from ground. Failure to do so can result in damage to the stereo and/or the vehicles electrical system.

White White/Black Green Green/Black Violet Violet/Black Gray Gray Black

= Left Front Positive (+) = Left Front Negative (-) = Left Rear Positive (+) = Left Rear Negative (-) = Right Rear Positive (+) = Right Rear Negative (-) = Right Front Positive (+) = Right Front Negative (-)

Black Yellow Red Blue/White

Orange Yellow/Black Green Pink Violet/White

= Chassis Ground (-12V) = +12V Battery Constant = +12V Ignition Switched = +12V Remote Output

(Amp Remote, Radio On Signal)

= Illumination Output = Mute = Park Brake = Speed Pulse

(VSS)

= Reverse

INTERFACE CONNECTIONS

Reverse Camera output to head unit and reverse camera input from optional camera

Power Harness Steering Wheel

Remote control connector to head unit

Dip Switches

Chime Box

1 2 3 4

DIP ON

DDR-VW01

Park Brake (Green)

Amp Remote Out (Blue/White)

Mute(Yellow/Black)

Speed Pulse (Pink) Reverse (Purple)

Aftermarket headunit unit

DDR-VW01

Speaker

Steering Wheel Control Jack

Aftermarket Radio Connector

Reverse Camera Input

Reverse camera (optional)

To car connector

ON = Pioneer1: SWC OFF = All other brands 2: CAMERA ON = PAL OFF = NTSC 3: RESET Turn from OFF to ON, then back to OFF. This will reset the Screen

settings back to default. Screen will change to red and back to

default to verify procedure. 4: N/A

1 43 2

DIP ON

DIP SWITCH SETTINGS

Up = OFF Down = ON

ALPINE Cut GREEN wire loop CLARION Cut VIOLET wire loop JVC Cut GREEN AND VIOLET loops PANASONIC Cut BLUE wire loop KENWOOD / JVC 2011-UP Cut BLUE AND GREEN loops SONY / PIONEER DO NOT CUT LOOPS

STEERING WHEEL WIRING CODES

To access the menu, push and hold the speech button for 2 seconds.This will enable the configuration root menu. To navigate through the menu options use the Track Up / Track Down SWC buttons. To select a menu option, push the speech button once.

Conﬁ guration Menu

Vehicle Settings

Infodapter Settings

Language

Version < Back

Vehicle Settings

Sport Mode Settings

Time/Date

Climate and air quality

Comfort Settings

Park assist and collision detection

Select “Vehicle Settings” menu to access factory settings originally accessed through OEM stereo.(For details of individual menu items refer to your vehicles user manual.)

Language

English

Deutsch

Nederlands

Francais

Italiano

Select “Language” menu to access available languages. If set to incorrect language, the language menu will always be the third selection down in the root menu.

Exterior ambient lighting

Power door locks

Remote locking,unlocking, starting

Polski

Infodapter Settings

Fig 2.

MENU ACCESS AND CONTROL

Steering Wheel Control Legend

1. Volume up

2. Track Down (Menu-Down)

3. Volume Down

4. Track Up (Menu-Up)

5. Answer

/ End

hold BT

6. Mute / Menu

hold

(Select)

Select “Infodapter Settings” menu to access and change attributes of the DDR-VW01 interface.

Select “Screen Size / Position” menu to calibrate video size and position. Use corner outline marks to ensure after market stereo reverse camera warnings appear outside of the DDR-VW01 video display. Refer to after market stereo’s manual for instructions to remove reverse camera guides and marks.

Preferences

Right

Driver Position Park Assist Version Camera Connected Yes Reverse Priority Park Assist

SpeedPark Brake Source Bluetooth On Steering Wheel 7 Function Logo Restore factory settings

Picture Settings

Brightness

Contrast

Saturation

<Back

Infodapter Settings

Screen Size / Position

Picture Settings

Preferences

<Back

Select “Picture Settings” menu to adjust the Brightness, Contrast, and Saturation of the DDR-VW01 video signal.

Park Brake Source:

Select Speed, Brake, or Always

On.

Bluetooth:

Enables Pick Up / Hang Up Steering Wheel Control functions.

Steering Wheel:

Select correct Steering Wheel Control button layout.

Logo:

Select for relevant Vehicle or

stereo brand logo to be displayed on factory for line dash display.(Does not support OEM NAV display.)

Restore Factory Settings:

Restores all DDR-VW01 settings

to defaults.

Screen Size/Position

Horizontal Size

Horizontal Position

Vertical Size

Vertical Position

< Back

Driver Position:

Select left or right hand drive.

Park Assist Version:

Select Park Assist graphic style.

Camera Connected:

Select if you have a Reverse Camera installed.

Reverse Priority:

Toggles between Park Assist

graphic or Reverse Camera as default view. Press “Source” button during reverse to toggle.

MENU ACCESS AND CONTROL ... Continued

On our website you can discover more about car stereo and video installation parts.

Scosche DDR-VW01 Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual