Scosche CIVIC 4-DR 2001,HA1567 Installation Manual
2001
HONDA
CIVIC
4-DR
Y ear: 2001 Make: Honda Model: Civic
IN-DASH APPLICA TION:
Dash Type: Single DIN w/Pocket Kit: HA1567 Harness: HA08
Antenna Adapter: None Factory Amplifier: None
FRONT SPEAKERS:
Door Speakers:
WHEN INST ALLING AN AFTERMARKET 5 ¼” OR 6 ½” SPEAKER, SAH6 ADAPTER IS REQUIRED.
7” 3-Hole Speaker in factory adapter Depth 1 1/2”
REAR SPEAKERS:
Rear Speakers: 7” 3-Hole speaker mounted to rear deck Depth 18”
WHEN INST ALLING AN AFTERMARKET 5 ¼” OR 6 ½ “ SPEAKERS, SAH6 AD APTER IS NEEDED .
WIRE COLOR CODES:
+12V Constant = White/Red
+12V Accessory Switched = Red/Yellow
-12V Chassis Ground = Black
+12V Illumination = Red/Black
+12V Dimmer = Red
Power Antenna = N/ A
Amp Remote = N/A
LF+ = Green/Black
LF- = Light Green
RF+ = Green/Yellow
RF- = Grey/Red
LR+ = Blue/White
LR- = Blue/Black
RR+ = Violet
RR- = Blue/Yellow1
NOTE: THIS MANUAL IS BASED ON CAREFULL Y DOCUMENTED RESEARCH. ABSOLUTE
ACCURACY IS ATTEMPTED BUT NOT GUARANTEED. USE THIS MANUAL AS A REFERENCE
GUIDE. SCOSCHE, INC. CANNOT BE RESPONSIBLE FOR INCONSISTENCIES THAT MAY OCCUR
© 2000 SCOSCHE INDUSTRIES, INC. ALL RIGHTS RESERVED
..
.
..
155
FOR MORE INFORMATION VISIT www.scosche.com
OR CALL SCOSCHE INDUSTRIES, INC. AT 800-363-4490
2001 Honda Civic
Sedan
PRELIMINARY: Disconnect the negative battery cable.
ANTENNA: The factory antenna is located rear window .
RADIO REMOV AL AND IN-DASH INST ALLA TION:
Note: The factory stereo provision is for a DINandHalf
radio with a pocket. When installing an aftermarket
DIN size radio, a dash installation kit is needed. We
recommend the Scosche HA1567B installation kit.
1. Using panel removal tool, pry out lower dash panel
pocket, unplug and remove.
2. Exract (2) Philips screws from bottom of radio bezel
assembly.
3. Pry out radio bezel assembly, disconnect and remove.
FRONT DOOR SPEAKER REMOV AL AND INST ALLA TION:
Note: The factory speaker provision is for a 6 1/2" speaker
mounted to a factory adapter. When installing an
aftermarket 5 ¼ or 6 ½” speaker no adapter is
required.
Note: Screws accessed through lower panel.
1. Using small pick, pry off screw cover in interior door handle
and extract (2) Philips screws, remove handle.
2. Remove window triangle using panel removal tool.
3. Using panel removal tool, pry off cover on bottom of door
pulland extract (2) Philips screws.
4. Pry off door panel by pulling out then up, disconnect and
remove.
5. Push in on tabs of speaker adapter to release, disconnect
speaker and remove.
REAR SPEAKER REMOV AL AND INST ALLA TION:
Note: The factory speaker provision is for a 6 ½”
mounted to the factory metal. When installing an
aftermarket speaker a speaker adapter is not required.
1. Fold rear seats down, pull back weatherstripping on B
pillar panels and remove.
2. Remove outer seat sections by extracting (2) 10 mm
bolts and pulling up.
3. Pull up and out on rear deck to remove, disconnect
third brake light.
4. Extract (3) 10 mm bolts from speaker, disconnect and
remove.
NOTE: THIS MANUAL IS BASED ON CAREFULLY DOCUMENTED RESEARCH. ABSOLUTE
ACCURACY IS ATTEMPTED BUT NOT GUARANTEED. USE THIS MANUAL AS A REFERENCE
GUIDE. SCOSCHE, INC. CANNOT BE RESPONSIBLE FOR INCONSISTENCIES THAT MAY OCCUR
156
..
.
..
© 2000 SCOSCHE INDUSTRIES, INC. ALL RIGHTS RESERVED
FOR MORE INFORMATION VISIT www.scosche.com
OR CALL SCOSCHE INDUSTRIES, INC. AT 800-363-4490
Loading...