Scosche BT1000 User Manual

OPERATION (cont’d)

TRANSFERRINg A mOBILE PHONE’S PHONEBOOK TO THE BT1000

With the BT1000 and mobile phone connected, press the “V-” for 3 seconds or until the
blue LED indictor comes on. The BT1000 will announce “Loading Phonebook. Please
wait”. The unit will continue to announce “Please wait” every 30 seconds until the process
is complete. When the phone transfer is complete the BT1000 will announce “Contacts
Saved” and the amount of SIM and phone memory remaining. If the memory is depleted
the BT1000 will prompt “Phonebook Full”. If the phonebook transfer is unsuccessful the
unit will announce “Loading Phonebook Failed”. Make sure your mobile phone supports the
transfer function. The BT1000 will store a maximum of 1000 phone numbers

REmOVINg PHONEBOOK ENTRIES

In standby mode, press and hold the “V+” and “V-” buttons simultaneously for 6 seconds.
The BT1000 will announce “Phonebook Deleted” and the entire phonebook will be de­leted from the unit’s memory.

TURNINg ON/OFF THE TEXT-TO-SPEECH FUNCTION

In standby mode, press and hold the “V+” button for 6 seconds. “Voice Prompt On” or
“Voice Prompt Off” will be announced to denote the unit’s current status.

RESTORE DEFAULT SETTINgS

To restore the BT1000 to its original setting, press and hold the “V+” and “V-” buttons
simultaneously for 10 seconds until the blue LED flashes rapidly. Press and hold the “V+”
and “V-” buttons simultaneously for 3 more seconds to power off the unit automatically.
When the process is complete the BT1000 will announce “Set Factory Default Complete”.

This Category II radio communication device complies with Industry Canada Standard RSS-310 for RX Siren.
This device complies with part 15 of the FCC Rules and RSS-210 for TX remote control. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. Any changes or modification
not expressly approved by the party responsible could void the user’s authority to operate the device.

FCC ID: IKQBT1000

HANDS-FREE BLUETOOTH

WITH SPEAKER BOX

PARTS INCLUDED

(1) Speaker box
(2) Remote control
(3) Microphone
(4) Power connections
(5) Hardware bag
(6) Instruction manual

BT1000

®

CAR KIT

Scosche Industries Inc. warrants this product to be free from defects in material and workmanship for a period of 90 days

LIMITED WARRANTY

from purchase. This Scosche product is sold with the understanding that the purchaser has independently determined
the suitability of this product. This warranty is offered to the original purchaser of the product only. This warranty does not
cover the product if physically damaged, subject to negligence or misuse, abuse, alteration, accident, or an act of GOD.
This warranty does not apply to product which has water or physically damaged by accident or which has been misused,
disassembled or altered.

The original dated sales slip or proof of purchase will establish warranty eligibility. If the product should prove defective
within the warranty period, return the product with proof of purchase to Scosche Industries Inc. Scosche, at its option, will
replace or repair the product free of charge and return the product postage paid. In no event shall Scosche Industries, Inc.
be responsible for claims beyond the replacement value of the defective product, or in any way be liable or responsible
for consequential or incidental damages. No express warranties and no implied warranties, whether for fitness or any
particular use or otherwise, except as set forth above (which is made expressly in lieu of all other warranties) shall apply
to products sold by Scosche. Scosche Industries cannot be held responsible for discrepancies/inconsistencies that may
occur due to automotive manufacturing changes or option.

8

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

©2009 SCOSCHE INDUSTRIES, INC. 300BT1000 8/09

INSTALLATION OVERVIEW

FIgURE 1

1. Primary mic location

2. Alternate mic location

INSTALLATION CAUTIONS & WARNINgS:

BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding
electrical service (AIR BAGS, ABS BRAKES, ENGINE/BODY COMPUTER AND BATTERY).

PLAN OUT YOUR INSTALLATION. You should pre-determine the location of the
microphone, remote control andspeaker box. This will save time and ease the installation
process.

USE A VOLT/OHM METER: We recommend the use of a LED style test light or Volt/Ohm
meter to test and locate all connections. Test lights could possibly damage a vehicle’s
computer system or cause an airbag to deploy.

DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with the brake/gas
pedals, steering column, or any other moving parts in the vehicle.

3. Remote control location

4. Speaker box location

OPERATION

mAKINg A CALL

Calls may be initiated from your mobile phone or directly from the BT1000 using voice-dial commands. Note:
Voice-dial feature must be supported by your mobile phone.

mAKINg CALLS FROm yOUR mOBILE PHONE
Dial directly from your mobile phone. The call is automatically connected to the BT1000.

RECEIVINg A CALL

The BT1000 will signal an incoming call with the announcement “Call from (Name or Number)”. Press the MFB
once on the BT1000 to answer the call.

ENDINg A CALL
During the call press the MFB to end the call. The BT1000 will announce “End call”.

REJECTINg A CALL

To reject an incoming call press and hold the MFB for 3 seconds The BT1000 will
announce “Reject call Successful”.

mAKINg A CALL USINg VOICE DIAL

Note: Make sure your mobile phone is voice-dial enabled. In Standby mode, short press the MFB. When you
hear a beep, say the voice tag. Important: Make sure to record a voice tag before using the voice-dial function.
This function is only applicable to mobile phones with Bluetooth Hands-Free Profile. Functionality varies
depending on the mobile phone model. Please refer to your mobile phone’s user guide for additional information.

LAST NUmBER RE-DIALINg

Press the “MFB” button twice to re-dialing the last number; The car kit announced” Redialing”.

TRANSFERRINg CALLS

Speakerphone to Mobile Phone - During a call, Short press “V+” and “V-” button and the call is routed to your
mobile phone.
Mobile Phone to Speakerphone - Press the “MFB” button once and the call is routed back to your mobile phone.

ADJUSTINg THE VOLUmE (ACTIVE CALL)

To Increase: Press the volume button “V+” to increase the volume by one level. Repeat until desired level is
reached.
To Decrease: Press the volume button “V-” to decrease the volume by one level. Repeat until desired level is
reached.

TEXT-TO-SPEECH VOLUmE (BT1000 CALLER ID ANNOUNCE)

To Increase: In standby mode press the volume button “V+” to increase the volume by one level. Repeat until
desired level is reached.
To Decrease: In standby mode press the volume button “V-” to decrease the volume by one level. Repeat until
desired level is reached.

ANSWERINg OR REJECTINg A SECOND CALL

To Answer: During a call with a second incoming call, short press the MFB to answer the second call and put
the first call on hold.
To Reject: During a call with a second incoming call, press the MFB for 3 seconds to reject the second call.

SWAPPINg CALLS

1. During a three-way call, press the MFB for 3 seconds to swap the call.

2. During a three-way call, short press the MFB to end the current call and automatically
switch to one of the other calls.

TEXT-TO-SPEECH LANgUAgE OPTIONS

Press and hold the “V+” button for 3 seconds and the BT1000 will announce “Select
language”. Repeat the process to select the desired language in the following order:
English, French, Italian, German & Spanish.

2

7