Scosche 142PA4BX,142PA8BX,142PA10BX,EFX 142PA4BX,EFX 142PA8BX,EFX 142PA10BX Installation Manual

AMPLIFIER INSTALLATION KITS

PARTS LISTS

142PA4BX
142PA8BX

142PA10BX

142PA4BX

• 17 ft. 4GA Power Cable
with Ring Terminal

•

2ft. 4GA Ground Cable
with Ultimate Ground Pre-terminated

• 17 ft. Remote Turn-On Wire

•

17ft.
6 ft. Split Loom Tubing

•
(1)

Mini-ANL Fuse Holder

•

•

(1) 1 OOA

•

(1)

Snap-in Firewall Grommet

•

(2)

Power/Ground Spade Terminals

(1)

Remote Spade Terminal

•

•

(1)

Remote Butt Connector

•

(2)

Fuse Holder Mounting Screws

•

(3)

UGT Self-Tapping Screws

•

(6)

8

Wiring your vehicle can be the most time consuming part of
be adhered to. The following basic tips can make the difference between

1.

RCA audio cables and power lines should be

WIRING KIT

Core Twisted Interconnect

Mini-ANL Fuse

II

Cable Ties

142PA8BX

• 17 ft. 8GA Power Cable
with Ring Terminal

•

2 ft. 8GA Ground Cable
with Ultimate Ground Pre-terminated

• 17 ft. Remote Turn-On Wire

• 17 ft. Core Twisted Interconnect
6 ft. Split Loom Tubing

•

•

(1)

Mini-ANL Fuse Holder

•

(1)

60A Mini-ANL Fuse

(1)

Snap-in Firewall Grommet

•

•

(2)

Power/Ground Spade Terminals

(1)

Remote Spade Terminal

•

•

(1)

Remote Butt Connector

•

(2)

Fuse Holder Mounting Screws

•

(2)

UGT Self-Tapping Screws

(6)

8

•

GENERAL WIRING

11

Cable Ties

run

separately.

WIRING KIT

an

installation, therefore certain good habits should

12

TIPS

volt power lines, when run next to

142PA10BX

• 17 ft. 1
with Ring Terminal

•

2 ft. 1
with Ultimate Ground Pre-terminated

• 17 ft. Remote Turn-On Wire

• 17 ft. Core Twisted Interconnect

•

6ft.

Split Loom Tubing

•

(1)

In-Line

•

(1)

30A

(1)

Snap-in Firewall

•

•

(2)

Power/Ground Spade Terminals

(1)

Remote Spade Terminal

•

•

(1)

Remote Butt Connector

•

(2)

UGT Self-Tapping Screws

•

(6)

8'1 Cable Ties

an

installation lasting on day or a lifetime.

OGA

Power Cable

OGA

Ground Cable

ATC

ATC

Fuse

WIRING KIT

Fuse Holder

Grommet

RCA

audio or
speaker wires, can induce a hum into the signal path of the system (radiated noise), even with well shielded wires.
Keeping these wires a minimum
in

the system.

2.

All wiring, whether power, speaker or RCA audio cables should be kept as far as possible from other high

of

six inches apart will help ensure that power line interference will not be present

voltage areas of the car's factory wiring. These can also induce noise into the system.

3.

Make certain that wiring

is

never run through openings which have rough metal edges, like fire walls, trunk
walls, etc. Also, beware that wiring may get pinched beneath seat tracks, clutch and brake pedals, etc.
Use vinyl tubing and grommets whenever necessary.

4.

When making any connection, use crimp connectors, or solder all connections and properly cover with heat
shrink tubing or electrical tape.

The following

• Wire strippers

• Soldering iron/gun

is

a list of common tools and supplies required when doing car audio installations:

• Wire crimpers

• Cordless drill/drill bits

1. Read all manufacturer warnings regarding vehicle's
electrical service, air bags, ABS brakes, engine
body computers.

2. Disconnect Negative (-) battery terminal before

beginning your installation (Figure

3. Wear eye and skin protection.

©2014 SCOSCHE INDUSTRIES, INC.

TOOLS

1).

& PREPARATION

&

FIGURE 1

Sl 300142PA4BX/142PA8BX/142PA 1

OBX

5/14

CABLE

FIGURE

2-

EFX

MINI

ANL

FUSE HOLDER FOR

142PA4BX

&

142PA8BX

HOUSING

ASSEMBLED

FUSE

HOLDER

---r----

METAL END

BLOCKS

RUBBER GASKETS

INSTALLATION:

1.

Before making battery connection, unscrew both end caps

2.

Push one side wire through fuse

3.

Pull

back, check grommet/o-ring

SCREWS

holder body for fuse

seals

and fasten caps again.

END CAP

CABLE

installation.

I

C

0

IN-LINE FUSE

,.

-~

1.

~

2.

®

FIGURE 3

HOLDER FOR

Flip

open cap and

30A

ATC

Close cap when finished.

fuse

as

carefully

shown.

142PA

1

OBX

insert (or remove)

FIGURE 4

BATTERY

CONNECTIONS

2