www.scorpioalarms.com
support@aritronix.com
Phone
(480)951-1109
Aritronix Ltd
16055 N. Dial Blvd. Suite B-10
Scottsdale, AZ 85260
SR-i900 Series
V9.3
FCC Notice
This device complies with Part 15 of FCC rules.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) This device must
accept any interference that may cause
undesired operation.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate this device.
FCC ID:
TRS-9 ARIMKF50
MCM-9
ARIMKF51
Save this information for future use.
Date of purchase _____/_____/_____
Place of purchase ______________________
______________________
Invoice/Receipt # _________________
Model Number _________________
Production Code _________________
Notes:
S
PECIAL NOTE ON RANGE
The average reception range is approximately ½ mile (800 meters ). The actual reception
range could be greater or less depending on the location and/or the presence of ob stacles
between the vehicle and the receiver. The reception range can also be affected by the
p
resence of strong electromagnetic interference from outside sources.
a3
Important Information
Installation
User’s Guide
Transceiver Information
Optional Accessories
A
ppendix
1
Installation
Component List 3
Planning the Installation 3
Installation Diagram 4
Installation Warnings and Notes 5
Mounting the Components 5
Routing the Antenna Wire 5
Making Connections 5
Color Code Chart 6
Using the T tap Connectors 6
User’s Guide
Remote Transceiver Icons
and Message Display 7
Transceiver Charging Instructions 7
Transceiver Battery Status 7
Motorcycle Battery Status 7
Transceiver Back Light 7
Operating Instructions 8
Auto Arm 8
Activate Perimeter Sensor 8
Panic / Stop Trigger 8
Auto Disarm 8
Manual Disarm 8
Manual Arm 8
Programming and Customizing
Instructions 9
Entering Programming mode 9
Selecting Perimeter Sensor Default 9
Selecting Transceiver Alert Type 10
Adjusting the Accelerometer 10
Selecting Siren Default 11
Setting the Clock 11
Encoding the Transceiver 12
Additional Information
Sensor Memory display 13
Motorcycle battery safeguard 13
Table of Contents
a2
Limited Warranty
Limited Warranty
Products manufactured by Aritronix, Ltd are warranted by the company to the original consumer
purchaser to be free from defects in workmanship and materials. Should a product be found defective
Aritronix shall repair or replace the product or any part of the product which Aritronix agrees is defective
without charge during the first 12 months from the date of original purchase provided that the product is
returned to Aritronix freight prepaid and accompanied by a copy of the purchase receipt.
This warranty does not apply to any product damaged by accident, physical or electrical misuse or abuse,
improper installation, alteration, any use contrary to its intended function, fire, flood, unauthorized repair or
any other acts of God.
Aritronix shall not be responsible for removal and/or reinstallation charges or theft of the motorcycle or its
contents or any incidental or consequential damages caused by any failure of the product to function
properly. Under no circumstances should this warranty or the product covered by warranty be construed
as an insurance policy against loss or damage of any kind.
Aritronix neither assumes nor authorizes any person or organization to make any warranties or assume any
liability in connection with the sale, installation, or use of this product.
This completes Aritronix warranty and no other warranty exists.
What should you do if you experience a problem with a Scorpio product?
First contact Aritronix, Ltd [Proof of purchase, installer and motorcycle information will be requested]. If
after assistance from our trained staff it is determined that the Aritronix product may be faulty then you will
be provided with detailed information on pro c e ssing a warranty claim and instructions on how to send the
product into our repair office. All warranty claims must contain a return material authorization (RMA).
Aritronix will not accept any package that has not been approved for warranty repair/exchange and an
issued RMA. Shi
pping
charges may apply.
a1
Problem Possible Cause Solution
Will not arm
RFID antenna not connected
Verify connection from MCM to RFID
antenna
Power or ground not connected
Verify connection to power lead and
ground connection
Orange wire not connected
Verify connection to 12 volt wire with
key on. (tail light on most bikes)
Turn signals will not
flash
Grey wires from GEN-1 not
connected or connected to wrong
wires
Test wires and change connections
to correct wires
Perimeter Sensor not
working
Sensor not connected Check connections
System set on default with sensor
off
Enter Programming mode and
change default
Ignition Disable does
not work
Orange wire from GEN-1 not
connected
Connect orange wire from GEN-1 to
12 volt (+) with ignition key on. In
most bikes that is the tail light wire
Ignition disable not connected to
correct wire on bike
Refer to options on the ignition
disable instruction page. Test
selected wire before reconnecting
RID-5 wires.
Troubleshooting guide
2
Manual Override Procedure
Programming Personal
Override Code 14
Enter Programming Mode 14
Select number of flashes for Code 14
Using Code in case of lost remote 14
Transceiver Information
Alarm Triggers 15
Range Confirmation Signal 16
Checking Violation Display 16
Transceiver Battery Information 17
Low Battery Stages 17
Optional Accessory Instructions
Perimeter Sensor (SN 5) 19
Back up Battery 20
Ignition Disable / Anti hijack Unit 21-22
Appendix
Trouble Shooting guide a1
Limited Warranty a2
Important Information / Notes a3
FCC Information a3
Special Note a3
3
Components
Component Check List
TRS-9
MCM-9
RFID antenna
AC Adapter
GEN-1(Bag)
T-taps x4
ACC-1(Bag)
Velcro Pieces x2
Zip Ties x4
Dust Cap x1
HAR-1 (Bag)
Planning the Installation
Check that your motorcycle battery is fully charged.
Check the layout of the motorcycle f or placement of components.
Verify that no moving parts interfere with the components or their wires.
Verify that chosen location is not near extreme heat.
TRS-9
Transceiver
MCM-9
GEN-1
ACC-1
HAR-1
A
C
Adapter
Installation
RFID
antenna
Appendix
4
--------------------- Installation Diagram --------------------
Extension 12”
A
ntenna 6”
5
: Connect the (HAR-1) harness to the MCM only after installation is completed. Make sure remote is
closed to bike to avoid a tri
gg
er.
Note: When the main harness (HAR-1) is plugged in, the siren should chirp. If the siren does not chirp; check
the alarm inline fuse, connection to battery
(+)
,and connection to ground (-).
: If the battery is to be removed, disconnect HAR-1 connector first. Reconnect only after battery terminals
are reconnected.
Installation Warnings and Notes
Mounting the Components
Select a suitable location underneath the seat or in a side cover. Mount components using velcro
or cable ties. Make sure that the components are not exposed or accessible.
o Place MCM as flat as possible to achieve best performance.
o Place RFID antenna under seat or tail section, do not chose a location that is covered with metal.
Routing the Antenna Wire
For best performance the last 6” of the antenna should:
o Be as vertical as possible.
o Be away from metal as much as possible.
Making Connections
The necessary connector or wires are found under the seat or in the tail section of the bike.
Removal of the tail section plastics or side cover might be necessary.
22
Ignition / Engine Control Wire Options:
Option #1: Positive lead wire on fuel pump
Option #2: Positive lead wire on fuel injection system
Option #3: Positive wire that goes to the ignition fuse in fuse box. This should be either a 10 or
15 amp fuse labeled IGN. (Carbureted Bikes Only)
Option #4: Ground wire from ignition module
Option #5: Positive wire from ignition module to ignition coil
Operating the Anti-Hijack Feature
While the engine is running, press and hold the transceiver’s button 1 and button 2 at the same time
for 3 seconds. The siren will begin to chirp confirming that the Anti-Hijack feature has been
activated. 15 seconds later, the siren will go off continuously, and the engine will shut down. To
disarm, turn off the ignition switch and press button 2.
To CUT wire on motorcycle
To Accessory Harness on Main
Control Module (MCM)
21
Ignition Disable / Anti-hijack Module (RID-5)
Installation
1. Cut the Ignition / Engine control wire (refer to options on page 22)
2. Attempt to start bike to test if correct wire is selected. If bike starts the wrong wire is selected.
(contact Aritronix for assistance) If bike does not start, correct wire was selected continue to
step 3.
3. When packaged the RID-5 wire ends have been treated with clear silicon to protect the ends
from fraying. Make sure they are stripped bare of this before continuing.
4. Connect one end of the cut wire to on e of the blue tabbe d wires in RID-5 with p rovided butt
connector or any other solid connection option.
5. Connect secon d end of the cut wire to second blue tabbed wire in RID-5 with provided butt
connector or any other solid connection option.
6. Test connections to insure that they are as solid as possible. *
7. Plug the RID-5 connector into the matching connector on the Accessory Harness.
8. Test RID-5 b y activating alarm (witho ut perimeter sensor) an d try to start bike. If bik e starts,
please contact Aritronix for assistance.
* Failure to test for a loose wire could cause an accidental engine cut off.
6
Color Codes:
(Color codes are not always valid. Always verify before making connections)
Ground (-) Tail Light Left Turn Signal Right Turn Signal
Honda Green Brown Orange Blue
Kawasaki Black Red Green Grey
Suzuki Black/White Brown Green or Black Grey
Yamaha Black Blue Green Brown
Harley Davidson Black Blue Brown Purple
Ducati Black Yellow White/Black White/Green
Using the T-tap Connectors and GEN-1 Connector
1) Place the female T-tap connector over wire, close and squeeze until it snaps.
2) Slip male T-tap connector over hinged end of the female connector to make a connection.
Motorcycle Wire
Female T-ta
p
1)
Motorc
y
cle Wire
Wire from (GEN-1)
Female T-ta
p
Male T-Tap (GEN-1)
--------------------- Skip this page if using Factory Connector Kit --------------------
Battery
Shock
Trigger
Perimeter
Trigger
24 hour
Clock / Text
display
Range
Indicator
Alert Type
Aud/Vibr
System Status
Button 2
Button 1
Tilt Trigger
Ignition
Trigger
Back up
Power
Trigger
Audible/
Silent
Alert Indicator
7
Reset
Button
Charger Input
Charging Instructions
We recommend that the transceiver be charged
for up to 12 hours to insure full life of the battery.
1. Plug in provided charger into the transceiver.
2. While the transceiver is charging the
icon will scroll from empty to full.
3. When the transceiver is fully charged the
icon will no longer scroll.
It’s recommended to recharge the transceiver
every day to maintain full function.
Remote Battery Status
The LCD will display 3 different icons to
show the transceiver battery status.
Motorcycle Battery Status
Every time the alarm is activated or deactivated,
the LCD will display a text message with the
current battery voltage.
If motorcycle battery drops below 11 volts the
screen will display CyCLE bAtt LO.
Transceiver Back light
From the main screen pres button 1or 2, the
screen back light will turn on for 2 seconds.
User’s Guide
Note: The system has to be correctly installed for at least 12 hours before full function of the
back-up battery can be used.
Note: If the system chirps only 2 times and it has been correctly connected for more the 12
hours, the battery needs replacement. (Contact Aritronix for replacement options)
Note: If power is purposely being interrupted when the alarm is activated, turn ignition key
on and off before disconnecting power to limit the back-up to two cycles instead of
six.
20
Back-up Battery (BAT-5)
The back-up battery provides the system the ability to transmit information and activate the siren
when power is interrupted. If power is ever interrupted while the system is activated the back-up
battery will be engaged. The transceiver will receive a trigger and the siren will sound in 30
second increments. If power is not restored the alarm will continue to transmit and sound for six
cycles.
To check the status of the back-up battery, activate the system using button 1.
• If the system chirps 3 times the back-up battery is in good working condition
• If the system chirps 2 times the back-up battery is not fully charged or not installed.
Perimeter Sensor (SN-5)
Mounting the SN-5
The Perimeter sensor uses high frequency microwave technology to detect mass densi ty movement
around the motorcycle. The signal can transmit through the seat, fiberglass, leather and plastic, but
not metal. It is recommended to place this sensor under the seat as close as possible to the center
of the motorcycle. With the provided Velcro, you can mount this sensor on top of the battery or any
flat surface, making sure that the top side of the sensor is facing upwards. Place the perimeter
sensor as faraway from the MCM as possible.
Adjusting the Sensor
Although the sensor is pre set from the factory it may be necessary to adjust the sensitivity to suit your
needs. Remove the plastic cap and turn the adjustment screw.
To increase sensitivity, turn adjustment screw clockwise.
To decrease sensitivity, turn the adjustment screw counter clockwise.
Plastic Cap:
Remove to adjust
sensitivity
To Accessory Harness on Main
Control Module (MCM)
Note: Do not turn sensitivity above half way. Doing
so may cause false alarms.
19 8
Operating Instructions
The SR-i900, by default, will be in auto arm mode and will activate with the perimeter sensor off and
the siren on, five seconds after turning the ignition key off.
Auto Arm
Activate perimeter sensor
Panic / Stop Trigger
(when system is armed)
Auto Disarm
Manual Disarm
Manual Arm
(system has to be manually disarmed first)
Walk next to
bike. Turn ignition
key on
Siren:
Chirp 3 Times
Turn Signals:
Flash 1 Time
Siren:
Chirp 1 Time
Turn Signals:
Flash 1 Time
Turn ignition key
off. Walk away
from bike
Press and hold
button 1
Siren:
Chirp 3 Times
Turn Signals:
Flash 1 Time
Siren:
Chirp 1 Time
Turn Signals:
Flash 1 Time
Press and hold
button 2
Note: If the system is manually disarmed it will stay
in disarmed mode. At this mode the system
will not auto arm upon turning ignition key off.
Siren:
Chirp 4 Times
Turn Signals:
Flash 1 Time
Press and hold
button 1 and 2
Siren:
Chirp 6 Times
Turn Signals:
Flash 1 Time
Press and hold
button 1
Press button 2
again to scroll
through
programmable
options
Press button 1 to
scroll between the
options
Programming and Customizing Instructions
Entering Programming Mode
Selecting Perimeter Sensor Default
Enter programming mode. The icon will begin to flash, press button 1 to enter the perimeter
sensor menu. The LCD will display the current setting. To program follow these steps:
Press button 1
to select icon
and to begin
programming
Programmable
options will be
displayed.
The selected
icon will flash
Note. Remote will time-out of programming mode after 20
s
econds. No changes will be saved.
Press button 2
Twice quickly
to enter
programming
mode
1)
2)
3)
Press
button 2 to
save and
exit
PEr: on – Perimeter sensor will be
enabled every time alarm is
armed
PEr: oFF – Perimeter sensor will be
disabled every time alarm is
armed
9
Note. To exit programming mode scroll through all icons once.
Optional Accessories:
Perimeter Sensor (SN-5)
Back-up Battery (BAT-5)
Ignition Disable (RID-5)
17
Transceiver Battery Information
The receiver consists of two functions RFID functions and Two-way FM communication.
Low Battery Stages
It’s recommended that the transceiver be charged daily. If the transceiver is not charged daily the
following stages will occur.
Low Battery: When the battery is low the
icon will cycle from 3 bars to 2 bars to 1 bar.
The transceiver should be charged as soon as possible.
Two-Way Off: If the transceiver is not charged, at some point (approximately 7 days) Two-way
communication will shut off. At this mode the LCD displays [rFId onLy]. The RFID
system will still operate and you will still be able to automatically and manually
arm and disarm the system.
No Response: If the battery is not recharged and all power is drained. The transceiver will not
respond. The transceiver has to be charged before it can operate the system
again.
10
Press button 1 to
scroll between the
options
Press button 1 to
scroll between the
options
Selecting Transceiver Alert Type (Audible/Silent/Vibrate)
Enter programming mode. Scroll to the the icon, press button 1 to select. The LCD will display
the current settings. To program follow these steps:
Adjusting the Accelerometer (Shock/Tilt) Sensor (proximity to MCM required)
Enter the programming mode. Scroll to the icon and press button 1 to select. The screen will
display the current shock setting, and the siren will chirp 1-5 times to confirm sensitivity level. To
program follow these steps:
Press
button 2 to
save and
exit
Press
button 2 to
save and
exit
– Transceiver will vibrate and
sound when a trigger occurs
ALL oFF – Transceiver will only flash
backlight when a trigger occurs
– Transceiver will only sound
when a trigger occurs
– Transceiver will only vibrate
when a trigger occurs
Off – Sensor turned off
1 – Least sensitive
5 – Most sensitive
Press button 1 to
scroll between the
options
Press button 1 to
adjust each
digit
Press button 2 to
toggle between
digits
Press
button 2
pass last
digit to
save
11
Selecting Siren Default
Enter programming mode. Scroll to the icon and press button 1 to enter the siren menu. The
LCD will display the current setting. To program follow these steps:
Setting the Clock
Enter the programming mode. Scroll to the time and press button 1 to select. The screen will display
time with the hour flashing. To program follow these steps:
Press
button 2 to
save and
exit
– Siren will sound and turn
signals will flash every time alarm is
triggered
– Siren will not sound and
turn signals will not flash every time
alarm is trigge r ed
Note. Clock onl
y
displays in 24 hour format (Military time
)
16
RCS (Range Confirmation Signal)
If the transceiver is within range of the MCM and the alarm is activated, the LCD will display icon.
If the transceiver does not receive the RCS; the icon will not appear.
Checking Violation Display with Time Stamp
Press button
1 twice
quickly
If no alarm triggers in memory, all
sensor icons will be displayed
If the system was triggered, the last triggered
sensor will be displayed
Trigger # Total # of
Triggers
Time of trigger
Press button 1 to scroll
between triggers
Or, press and hold button 2 for
two seconds to erase memory.
15
Alarm Triggers
When the system is triggered, the siren will sound and the turn signal lights will flash. The transceiver’s
LCD will display the following messages:
1. If bike is bumped, the LCD will display
icon. The siren on the bike will sound for 5
seconds and the lights will flash. This cycle will repeat twice.
2. If the perimeter sensor triggers a full alarm cycle, the LCD will display icon. The siren on
the bike will sound for 5 seconds. This cycle will repeat twice
(Note: The turn signal lights will not flash for a perimeter sensor trigger).
3. If the bike is tilted, the LCD will display icon. The siren on the bike will sound for 30
seconds and the lights will flash. This cycle will repeat six times.
4. If the ignitio n swi tc h i s tur ne d on or tam p er ed wi th , the L C D wil l d is pl ay
Icon. The siren on
the bike will sound for 30 seconds and the lights will flash. This cycle will repeat six times.
5. If the main harness or battery power supply is disconnected (assuming optional Back-Up
battery is installed), the LCD will display icon. The MCM-9 will still continue to sound
and transmit from its internal power source. The siren on the bike will sound for 30 seconds.
This cycle will repeat six times.
6. The transceiver will continue to flash the triggered icon until any button is pressed.
Transceiver Information
12
Button 1
Encoding a Transceiver
1. Unplug HAR-1 from the MCM-9 and plug it back in, the siren will chirp 2 times and the lights
will flash 2 times.
2. Within 6 seconds of plugging in the HAR-1 turn ignition switch “ON” and “OFF” 3 times.
3. If step 2 is done correctly and within the time allowed , the siren will chirp 2 times and the
lights will flash an additional 2 times to confirm that the system is in “Learn Mode”.
4. Press and hold button 1 until the system chirps 2 times and the lights flash 2 times to
indicate that the MCM has learned the code. The transceiver echoes 4 chirps and the LCD
displays [LErn donE] to confirm that the transceiv e r is enc oded.
5. If you are encoding a second transceiver repeat step number 4 for the second transceiver
before continuing to step number six.
6. Turn ignition “ON” and “OFF” to exit “Learn Mode”.
Note: The transceivers are programmed from the factory. Encoding is only necessary should
the transceiver lose its code and will not arm or disarm the security system or if a second
or replacement remote is obtained.
13
Sensor Memory Display
When the system is disarmed the turn signals will flash to indicate if there h as bee n an a larm trigg er.
The lights will flash onc e to indica te that the system has been disarmed, additional flashes indicate
that the following tri gger has occurred:
1 flash then 1 additional flash = Shock Trigger
1 flash then 2 additional flashes = Tilt Trigger
1 flash then 3 additional flashes = Perimeter Sensor Trigger
1 flash then 4 additional flashes = Back-Up battery Trigger
1 flash then 5 additional flashes = Ignition Trigger
Motorcycle Battery Safeguard with “sleep mode”
• If the optional perimeter sensor is being used and the alarm is armed for more then 10 days the
system will automatically disable the perimeter sensor.
• If the alarm is armed for more than 30 days, the system will automatically shutdown its RF
capabilities. In this mode the transceiver will no longer be able to operate the system but the
system is still armed and protecting the bike.
• To disarm, trigger the alarm, and press button 2.
A
dditional Information
14
Programming Personal Override code (This feature will work on most but not all bikes)
A personal override code will be a sequence of left – right - left turn signal flashes that can be used if
the remote is lost to disable the alarm:
Enter programming Mode
1. Manually disarm system
2. Turn ignition on – off – on – off – on. The siren will chirp one time to confirm.
3. Press and hold button 1 and 2 at the same time for a few seconds until alarm chirps 3 times
and flashes lights 3 times to confirm.
Select number of flashes for Code
The code will be a combination of left-right-left-right turn signal count.
1. Turn on left turn signal to desired number of flashes. (up to 9)
2. Turn on right turn signal to desired number of flashes. (up to 9)
3. Turn on left turn signal to desired number of flashes. (up to 9)
4. Turn on right turn signal once to exit mode. (Will only register one flash)
5. When done, the remote will display the sequence on the screen
until a button is pressed or for up to 30 seconds.
6. The bike will flash the code in the same sequence entered.
Using code in case of lost remote
1. Turn ignition key to o n posi tion . Let al arm go th ru a fu ll cy cle unti l the tu rn sign al li ghts sto p
flashing. (If siren is turned off, you do not need to wait for a full cycle)
2. Enter code as originally entered.
3. When correct code is entered the alarm will deactivate
Manual Override Procedure
(LCD screen will confirm code)
Loading...