MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
User Manual
MS-H-Pro Digital Hotplate Magnetic Stirrer
MS-Pro Digital Magnetic Stirrer
Please read the User Manual and the related Video of this
instrument on our website carefully before use, and follow
all operating and safety instructions!
The website www.scilogex.com
Cat No.12300137
1
Contents
Contents 1
Preface 2
Service 2
Warranty 2
1 Safety Instructions 3
2 Proper use 4
3 Inspection 5
3.1 Receiving Inspection 5
3.2 Listing of Items 5
4 Trial run 5
5 Control and Display 6
5.1 Control Elements 6
5.2 Display 7
6 Initialization 7
6.1 Initializing Sequence 7
6.2 Default Settings 7
6.3 Resetting Parameters to Factory Settings 8
7 Operating Modes 8
7.1 Operation Mode of MS-H-Pro 8
7.2 Operation Mode of MS-Pro 8
8 Function: Heating(MS-H-Pro) 9
8.1 Working with External Temperature Sensor 9
8.2 Residual Heat Warning（HOT）
10
8.3 Setting the Safety Temperature 10
9 Function: Stirring 11
9.1 Basic Stirring 11
9.2 Stirring Bar Breakaway Monitoring 11
10 Remote Control 12
11 Faults 12
12 Maintenance and Cleaning 13
13 Associated Standards and Regulations 14
14 Technical Data 14
15 Products andAccessories 15
16 Main Spare Parts Inside back
16.1 Spare Parts Diagram of MS-(H)-Pro Inside back
16.2 List of Spare Parts of MS-(H)-Pro Inside back
2
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
Preface
Welc ome to th e “M S-(H ) -Pro Dig ital （Hot plate ）
Magnetic Stirrer User Manual”. Users should read this
Manual carefully, follow the instructions and procedures,
and beware of all the cautions when using this instrument.
Service
When help needed, you can always contact the Sevice Department
of manufacturer for technical support in the following ways:
SCILOGEX, LLC
500 Four Rod Road
Suite 122
Berlin, CT 06037
USA
Tel：1- (860) 828-5614
Fax：1- (860) 828-5389
E-mail: info@scilogex.com
Website：Http://www.scilogex.com
Please provide the customer care representative with the
following information：
• Serial Number（on the rear panel）
• Description of problem (i.e., hardware or software)
• Methods and procedures adopted to resolve the problems
• Your contact information
Warranty
You have purchased a Scilogex instrument. This instrument
is warranted to be free from de fects in mate rials and
workmanship under normal use and service, for a period
of 24 months from the date of invoice. The warranty is
extended only to the original purchaser. It shall not apply to
any product or parts which have been damaged on account
of improper installation, improper connections, misuse,
accident or abnormal conditions of operation.
For claims under the warranty please contact your local
dealer. You may also send the instrument direct to our works,
enclosing the invoice copy and by giving reasons for the
claim. You would be solely liable for freight costs.
3
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
1 Safety Instructions
• When work ，wear the personal guard to avoid the risk
from:
- Splashing and evaporation of liquids
- Release of toxic or combustible gases.
• Set up the instrument in a spacious area on an stable,
clean, non-slip, dry and fireproof surface, do not operate
the instrument in explosive atmospheres, with hazardous
substances or under water.
• Gradually increase the speed, reduce
the speed if :
- The stirring bar breakaway because of too high speed
- The instrument is not running smoothly, or container
moves on the base plate.
• Temperature must always be set to at least 25 ℃ lower
than the fire point of the media used.
• Beware of hazards due to:
- Flammable materials or media with a low boiling
temperature
- Overfilling of media
- Unsafe container
• Process pathogenic materials only in closed vessels.
• If the case of the stirrer bar is PTFE,please note：
elemental fluorine, three fluoride and alkali metals will
corrode the PTFE and Halogen alkanes make it expansion at
room temperature
Molten alkali ，alkaline earth metals or their solution, as
well as the powder in second and third ethnic of the Periodic
Table of Elements will have chemical reaction with PTFE
when temperature reaches 300 ~ 400 ℃ .
• Check the instrument and accessories before hand for
damage each time you use them. Do not use damaged
4
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
components. Safe operation is only guaranteed with the
accessories described in t he “Accessories” chapter.
Accessories must be securely attached to the device and
cannot come off by themselves. Always disconnect the plug
before fitting accessories.
• Ensure that the external temperature sensor is inserted in
the media to a depth of at least 20 mm.
• When using metal vessels, do not place the temperature
sensors on the bottom of the vessel. Placing sensors on the
vessel bottom can cause excessively high temperatures to be
measured especially in media which have poor conductivity.
The tip of the measuring sensor must be at least 5 mm from
the vessel bottom; a distance of 10 mm is ideal.
• The instrument can only be disconnected from the main
power supply by pulling out the mains plug or the connector
plug.
• The voltage stated on the label must correspond to the
main power supply.
• Ensure that the mains power supply cable does not touch
the heating base plate. Do not cover the device.
• The instrument may only be opened by experts.
• Keep away from high magnetic field.
• Observe the minimum distances between the devices,
between the device and the wall and above the assembly
(min. 100 mm).
>100mm
Figure 1
2 Proper use
The instrument is designed for mixing and/or heating liquids
in schools, laboratories or factories. This device is not
suitable for using in residential areas or other constraints
mentioned in Chapter 1.
5
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
3 Inspection
3.1 Receiving Inspection
Unpack the equipment carefully and check for any damages
which may have arisen during transport. If it happens, please
contact manufacturer for technical support.
Note:
If there is any apparent damage to the system,
please do not plug it into the power line.
3.2 Listing of Items
The packing includes the following items:
Items Qty
Main unit 1
Power cable 1
Stirrer bar 1
User manual
1
Table 1
4 Trial run
• Make sure the required operating voltage and power
supply voltage match.
• Ensure the socket must be earthed reliably.
• Ensure the power be off
• Plug in the power cable，ensure the power be on and
begin initializing.
• Add the medium into the vessel with a stirring bar.
• Put the vessel on the workplate.
• Set the rated stirring speed and start stirring.
•
Observe the stirring bar and LCD display.
• Set the rated temperature and start heating.
• Observe the real temperature on LCD display.
• Stop the heating and stirring functions.
If these operations above are normal, the device is ready
to operate. If these operations are not normal, the device
may be damaged during transportation, please contact
manufacturer for technical support.
6
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
5 Control and Display
5.1 Control elements
Mode Key
Function
Key
LCD
Temperature control knob
(MS-H-Pro)
LED Heat
(MS-H-Pro)
Speed control knob
LED Stir
Figure 2
Figure 3
Items Descriptions
Speed control knod
Stir
Set the rated rotary speed. The function
“Stirring” is switched ON or OFF via
push the knob.
Tempe r a ture co n trol
knob
Heat
(MS-H-Pro)
Set the rated temperature. The function
“heating” is switched ON or OFF via
push the knob.
Mode Key
Mode
Shift among the three operating modes:
A, B, and C mode.
Set Key
Set
Setting all parameters of the device
LCD
LCD displays the r
eal working state and
all settings.
LED Heat
(MS-H-Pro)
When the heating function is switched
ON, the LED Heat is lit.
LED Stir
When the stirring function is switched
ON, the LED Stir is lit.
Power Switch Switch ON or OFF the instrument.
Table 2
7
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
5.2 Display
T e m p St i r
℃
R e m o t e
Se t
Probe H o t CBA
E r r
Real value
Rated
va lu e
Temperature S t i r
Error
Se t
Mode
HotPlatewar
ning
External
probe
Remote
control
Figure 4
Characters Descriptions
Temp and ℃
Display temperature when the heating function is
switched ON.
Stir
Display stirring state when the stirring function is
switched ON.
Mode
Display the setting mode in order of A, B and C
after pressing mode key.
Set Press setting key to set function, and display Set characters.
Hot
Display hot warning if the heating plate temperature is
above 50℃ after switching OFF the heating function.
Probe Di
splay when using external probe.
Remote Display in case of remote control.
Err Display in case of error happening.
Rated value 、
Real value
Display value in case of heating or stirring function
switching ON.
Table 3
Note:
If both heating and stirring functions have been
started at the same time, the display of function
“heating” always has higher priority. If in this
case speed is changed via the stirring knob, it
display stirring speed and reverses to temperature
in the duration of 5 seconds.
6 Initialization
6.1 Initializing sequence
• Turn on instrument by the power switch.
• The “Heat” and “Stir” LEDs and the LCD display
flash about 3 times.
• LCD displays the workplate,s safe temperature limit in
“SAFE xxx°C”.
• LCD displays residual heat warning “rES On/OFF”.
• LCD displays stirring bar breakaway monitoring “br On/
OFF”.
• LCD displays operating modes(A、B、C).
• LCD displays the “Probe” character s in case of
connecting with external temperature sensors.
6.2 Default settings
MS-(H)-Pro is supplied with the following default settings
8
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
Items Default settings
Operating mode A
Setting temperature (°C ) 25
SAFE (℃ ) 350
Setting rotary speed (rpm) 100
Residual heat warning On
Stirring bar breakaway monitoring OFF
Table 4
6.3 Resetting parameters to factory settings
Reset the parameters to the default settings, as follows:
• Turn off by the power switch‘O/I’to‘O’
• Have the keys “Set” and “Mode” pressed down at
the same time and switch on the main O/I switch. Release
buttons after 5 seconds.
• The unit is now set to the factory default settings.
7 Operating modes
7.1 Operation modes of MS-H-Pro:
Operation mode A
●
MS-H-Pro has heating and stirring functions.
●
Users can control on the front panel or by remote PC.
●
Residual temperature warning, safe temperature limit and
stirring bar breakaway monitoring can be set in this mode.
Operation mode B
●
MS-H-Pro has heating and stirring functions.
●
Users can control on the front panel or by remote PC.
●
Residual temperature warning, safe temperature limit and
stirring bar breakaway monitoring can be set in this mode.
Operation mode C
●
MS-H-Pro maintains the state of the heating and stirring
functions before the last switching off (mains OFF), as well
as the data set last can be changed.
●
Remote control can be used without supporting external
temperature sensors.
●
Residual temperature warning, safe temperature limit
and stirring bar breakaway monitoring can’t be set in this
mode.
7.2 Operation modes of MS-Pro:
Operation mode A
●
MS- Pro has heating and stirring functions.
●
Users can control on the front panel or by remote PC.
●
Stirring bar breakaway monitoring can be set in this
mode.
9
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
Operation mode B
●
MS-Pro maintains the state of the heating and stirring
functions before the last switching off (mains OFF), as well
as the data set last can be changed.
●
Remote control can be used.
●
Stirring bar breakaway monitoring can’t be set in this
mode.
Note:
Mode changing and parameter setting is forbidden
when the instrument is running.
Switch OFF “Stir”and “Heat”control knob
in advance before change mode.
8 Function: Heating(MS-H-Pro)
The device is controlled by Digital Temperature Control
Technology ,which has two separate safe circuit. The
hotplate is kept at a constant temperature by a digital control
circuit. The hotplate temperature can also be monitored from
a separate, adjustable safety circuit. The two temperature
sensors (Pt1000) internal for temperature control are built
into the hotplate.The single external Pt1000 can monitor the
temperature of sample.
If external temperature sensors needed, it must be plugged in
before the device is switched ON.
• Ensure the external temperature sensors connecting
firmly before heating.
• Set the temperature via turn
ning the temperature control
knob slowly to the ideal scale .
• When the heating function is switched on, the LED
“Heat” will light up and the LCD will display the real
temperature.
• The rated temperature will be displayed on the right-hand
side of the LCD as well as Temp and °C characters.
• The heating function is switched on or off via pushing the
heat knob.
8.1 Working with external temperature sensor
Figure 5
10
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
In the B mode, if the external temperature sensor is not
plugged in, “Probe” will flash. If plugged in, “Probe”
will be shown on the digital display to indicate that the
sensor is operating. The external temperature sensors’
value and actual temperature are displayed.
Compared with the temperature control of the hotplate, the
external temperature sensor can control the medium’s
temperature more precisely.
Warning!
Forbid to Plug in/pull out external temperature
sensor in heating.
8.2 Residual heat warning（HOT）
In the A or B mode, users can set the residual heat warning
function, as follows:
• Press continuously the function setting key till the LCD
displays “rES”.
Press the temperature regulation key to switch on or off
the residual heat warning function, and the LCD displays
“On” or “OFF”.
• Press continuously the function setting key till “Set”
disappear.
• The residual heat warning function has been switched on
or off.
In order to prevent the risk of burns from a hotplate, MS-HPro has a residual heat warning function. When the heating
function is switched off and the hotplate temperature is
still above 50℃, “Hot” will flash to warn that there is a
hazard of burns from the hotplate. Wh
en the heating plate
temperature drops to below 50℃, the unit will automatically
switch off. If users want to turn off the LCD immediately,
just pull out the plug directly. When the plug is pulled out,
the residual heat warning function can not be run.
8.3 Setting the safety temperature
In the A or B mode, the safety temperature can be set, as
follows:
• Press continuously the function setting key till the LCD
displays “SAFE”.
• Adjust the temperature setting key to set the safety
temperature from 100 to 350℃.
• Press continuously the function setting key till “Set”
disappear.
• The value of the safety temperature has been stored and
setting is completed.
11
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
9 Function: Stirring
9.1 Basic Stirring
The function “stirring” is switched on or off via the rotary
stirring knob. The motor speed is set on the knob (100 to
1500 rpm in steps of 10 rpm ).
When both the function heating and stirring are switched on
and those above operations are done, the LCD will shift to
the speed value and come back to the temperature value in
about 5 seconds.
9.2 Stirring bar breakaway monitoring
In the A or B mode, the stirring bar breakaway monitoring
can be set, as follows:
• Press continuously the function setting key till the LCD
displays “br”.
• Press the function setting key to switch on or off the
stirring bar breakaway monitoring function, and the LCD
displays “On” or “OFF”.
• Press continuously the function setting key till “Set”
disappear.
• The stirring bar breakaway monitoring function has been
set.
Breakaway can occur when stirring at high speeds , when
large stirring bars are being driven at speeds close to the
maximum magnetically torque or sample viscosity changes.
Using MS-(H)-Pro, stirring bar breakaway monitoring
function can be set at the rotary speed range between 300
and 1500 rpm. When stirring bar breakaway is detected,
stirring is stopped immediately to enable the stirring bar
to be picked up. After this, stirring starts again and rotary
speed increases up to the set speed. If a further stirring bar
breakaway occurs within the next 3 minutes of stirring at a
constant set speed, the stirring bar will be picked up again
and stirring will restart but this time at the set speed reduced
by 100 rpm. The speed will be reduced each time in 100 rpm
steps until the minimum of 200 rpm is reached. In this case
you should select new test conditions.
IMPORTANT:
You must calibrate and test the stirring bar breakaway
monitoring function for your particular configuration taking
into account the stirring bars, speed, vessel and medium you
are using.
12
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
10 Remote control
Figure 6
The unit can be controlled from an external PC (using the
dedicated software) via the RS232 C serial interface fitted to
the unit. Data communication from laboratory instrument to
computer is only possible on demand of the computer.
• The functions of the interface lines between laboratory
in strument and automati on system are selected from
the s peci fie d s ignals of t he EIA-stan dard RS 232 C,
corresponding with DIN66020 Part 1. The allotment of the
bushing can be taken from illustration.
• For the electrical properties of the interface lines and
for the allotment of the signal status, standard RS232 C,
corresponding with DIN66259 Part 1 applies.
• Transmission method: Asynchronous signal transmission
in start-stop-operation.
• Mode of transmission: Fully Duplex.
• 1 start bit;
7 character bits; 1 parity bit [straight (even]);
1 stop bit.
• Transmission speed: 9600 bit/s
NOTE:
Forbid to plug i n or plug out the RS 232C
communication line!
11 Faults
• Instruments can’t be power ON
- Check whether the power cable is plugged
- Check whether the fuse is broken or loose
• Fault in power on self test
- Switch OFF the unit, then switch ON and reset the
instruments to factory default setting.
• Temperature cannot reach set point
- Check whether the safety temperature value is set too low
• Stir speed cannot reach set point
- Check whether the stirring bar breakaway monitoring is
ON
- Excessive medium viscosity may cause abnormal speed
reduction of the motor
13
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
• Heating cannot be started when push the temperature
control knob, or stirring cannot be started when push the
speed control knob.
- Check whether the unit is in the mode setting program,
- Exit from the mode setting and restart the heating/
stirring functions.
• Unit cannot be powered off when switched off.
- Check if the residual heat warning function is still ON
and hotplate temperature is above 50℃ (the LCD still work
and “Hot” flash).
- Turn off residual heat warning function before powered
OFF the unit.
If these faults are not resolved，plesse set the instruments
to factory default setting，or take the unit to your technical
service center.
12 Maintenance and Cleaning
• Proper maintenance can keep instruments working in a
good state and lengthen its lifetime.
• Be careful not spray the cleanser into the instrument
when cleaning.
• Unplug the power line when cleaning.
• Only use cleanser that we advised as below:
Dyes Isopropyl alcohol
Construction materials
Water containing tenside /
isopropyl alcohol
Cosmetics
Water containing tenside /
isopropyl alcohol
Foodstuffs Water containing tenside
Fuels Water containing tenside
Table 5
• Wear the proper protective gloves during cleaning of the
instrument.
• B e f o r e u sin g oth e r m e t hod f o r c lea n i n g o r
decontamination, the user must contact the manufacturer
ascertain that
this method does not destroy the instrument.
• The enamel makes the hotplate easier to care for and
more resistant to acids and bases. Because of it, however, the
heating plate is also more susceptible to extreme fluctuations
in temperature and the force of impact. This can result in
cracks forming or the coating flaking off.
• The instrument must be cleaned and put it into the
initial packaging carton before sending to service for repair,
avoiding the contamination of hazardous.
• Use the instrument in a dry clean room and temperature
stable environment.
14
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
13 Associated standards and regulations
Construction in accordance with the following safety
standards:
EN 61010-1
UL 3101-1
CAN/CSA C22.2(1010-1)
EN 61010-2-10
Cons truction in accordance with the fol lowing EMC
standards:
EN 61326-1
Associated EU guidelines:
EMC-guidlines: 89/336/EWG
Instrument guidelines: 73/023/EWG
14 Technical data
Voltage [VAC] 200-240 / 100-120
Frequency [Hz] 50/60
Power [W]
550(MS-H-Pro) /50(MSPro)
Stirring point position
quantity
1
Max. stirring quantity (H2O) [L] 20
Max. magnetic bar [mm] 80
Motor type
External rotor
brushless motor
Max. power input of motor [W] 18
Max..power output of motor [W] 10
Speed range[rpm] 100 ~ 1500
Rotary speed display LCD
Speed display accuracy [rpm] 1
Hotplate material Stainless steel/porcelain enamel
Ø of the hotplate [mm] Ø 135
Heating power[W] 500(MS-H-Pro)
Heating rate (1L wate
r) [K/min] 6(MS-H-Pro)
Temperature range [℃] RT~340(MS-H-Pro)
Temperature display[℃] LCD(MS-H-Pro)
Temperature display accuracy [℃] 0.1(MS-H-Pro)
Control accuracy of heating
temperature [℃]
1(MS-H-Pro)
15
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
The safety temperature range
of the hotplate [℃]
100~350(MS-H-Pro)
Temperature sensor in medium PT1000(MS-H-Pro)
Control accuracy of heating
temperature with temperature
sensor [℃]
0.2(MS-H-Pro)
Dimensions (mm) 280×160×85
Weight [kg] 2.8
Permitted ambient
temperature[℃]
5 ~ 40
Permitted relative humidity 80%
Protection class acc. to DIN 60529 IP42
RS232 interface Yes
Table 6
15 Products and Accessories
Cat.No. Description
811123019999
MS-H-Pro Digital Hotplate Magnetic
Stirrer ，Porcelain enamel, Cn plug,
220V/50Hz/60Hz
811123029999
MS-H-Pro Digital Hotplate Magnetic
Stirrer ，Porcelain enamel,USA plug,
110V/50Hz/60Hz
811123039999
MS-H-Pro Digital Hotplate Magnetic
Sti r rer ， Stain l ess S teel, Cn plu g ,
220/50Hz/60Hz
811123049999
MS-H-Pro Digital Hotplate Magnetic
Stir rer ，Stainless Steel , USA plug,
110V/50Hz/60Hz
811123059999
MS-H-Pro Digital Hotplate Magnetic
Stirrer ，Porcelain enamel, Euro plug,
220/50Hz/60Hz
811123069999
M
S-H-Pro Digital Hotplate Magnetic
Stirrer ，Porcelain enamel, UK plug,
220V/50Hz/60Hz
811123109999
MS-H-Pro Digital Hotplate Magnetic
Stir rer ，Stainless St eel, Euro plug,
220V/50Hz/60Hz
811123119999
MS-H-Pro Digital Hotplate Magnetic
Sti rre r ，S tain less St eel, UK plug ,
220V/50Hz/60Hz
811123149999
MS-H-Pro Digital Hotplate Magnetic
Stirrer ，Porcelain enamel, USA plug,
220V/50Hz/60Hz
16
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
811113019999
MS-Pro Digital Magnetic Stirrer ，Stainless
Steel，Cn plug, 220V/50Hz/60Hz
811113029999
MS-Pro Digital Magnetic Stirrer ，Stainless
Steel，USA plug, 110V/50Hz/60Hz
811113039999
MS-Pro Digital Magnetic Stirrer ， Stainless
Steel，Euro plug, 220V/50Hz/60Hz
811113049999
MS-Pro Digital Magnetic Stirrer ，Stainless
Steel，UK plug, 220V/50Hz/60Hz
811113089999
MS-Pro Digital Magnetic Stirrer ，Stainless
Steel
，USA plug, 220V/50Hz/60Hz
Accessories
18900001
MS 135.1 Carrie r pla te，Used with
MS135.2--5
18900002 MS 135.2 Quarter, 4 ml reaction vessel
18900003 MS 135.3 Quarter, 20 ml reaction vessel
18900004 MS 135.4 Quarter, 30 ml reaction vessel
18900005 MS 135.5 Quarter, 40 ml reaction vessel
18900048 MS 135.6 Quarter, 8ml reaction vessel
18900049 MS 135.7 Quarter, 16 ml reaction vessel
18900006 Stirring bars（10mm
x 6mm），1pcs/pk
18900007 Stirring bars（15mm x 8mm），1pcs/pk
18900008 Stirring bars（20mm x 8mm），1pcs/pk
18900009 Stirring bars（25mm x 8mm），1pcs/pk
12500005 Stirring bars（30mm x 6mm），1pcs/pk
18900011 Stirring bars（40mm x 8mm），1pcs/pk
12500004 Stirring bars（50mm x 8mm），1pcs/pk
18900013 Stirring bars（65mm x 8mm），1pcs/pk
18900014 Stirring bars（80mm x 13mm），1pcs/pk
18900015 Stirring bar mover，1pc
18900016 PT1000 Tempersture probe for MS-H-pro
18900017 Stander kit of PT1000
18900018
F100 unit cover，for none heat plate
model
MS-Pro,MS-S
18900019
F101 unit cover，for heat plate model
MS-H-Pro,MS-H-S
18100319
9-Pin interface line, suitable for StirPC
software.
Table 6
Note：The software StirPC can be download free on our
website www.scilogex.com
MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
16 Main spare parts
16.1 Spare parts diagram
1 2 3 4
5
789
10
11
12
13
14
15
16
17
18 19620
Figure 8
16.2 List of spare parts
No Name No. Name
1 Workplate 11 Driver circuit board
2
Hole for external
temperature
sensor holder
12
Direct-current Motor
without brush
3 Mains switch 13 Turntable
4 Housing 14
Internal temperature
sensors
5 Ventilation 15 Permanent magnet
6 Control panel 16 Heating parts
7
External
temperature
sensors’ socket
17 Protective plate
8
Remote control
socket
18 Rear board
9 Mains socket 19 Rubber bush
10
Main circuit
board
20 Interface circuit
board
SCILOGEX, LLC
500 Four Rod Road
Suite 122
Berlin, CT 06037
USA
Tel：1- (860) 828-5614
Fax：1- (860) 828-5389
E-mail: info@scilogex.com
Website：Http://www.scilogex.com
Loading...