ACCESSORIES
The LS-30 system includes a full range of accessories, so you can
customize many feature of your security system.
All the radio transmitters used in the LS-30 system, except the Remote
Controller, have a unique random code that is set by the factory with
16,777,216 combinations in total. Also with specially designed
transmission timing control, the LS-30 system can effectively prevent
mutual interference from other transmitters in the system. The Remote
Controller uses copy-preventing hopping-code technology, changing its
radio code every time you press the button. The combinations possible
through this hopping-code are up to 7.3 X 1019. To comply with the
regulations in most countries, radio power is limited to below 10mW, and
effective range is about 100 meters measured at open field. The range may
be somewhat less indoors, depending on the layout of building construction
and furniture.
You may enroll all the wireless accessories and change their related settings,
either through the guidance of the interactive LCD display on the Base Unit
explained in the “INSTALLATION” section that follows, or by using a
computer with the proprietary software “HyperSecureLink” through an
interface adapter, which offers a quicker and simpler way to perform the
installation in.
NOTE: The changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
The comply with the FCC RF exposure compliance requirements, this
device and its antenna must not be co-located or operating to conjunction
with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
SMOKE DETECTOR
INSTALLATION
1. Loose the bottom base of the SM-3S, and insert 9V battery properly.
2. Select “Installer Mode” on the Base Unit, and enter Installer Password to gain
access authority. Then select \Set Device\Enroll Device\Fire Sensor\Enter Zone
No. to enroll the ID of SM-3S by pressing its TEST button. You may change its
various attributes under \Set Device\Change Device Setting\Fire Sensor Change, to
fulfill different requirements.
3. Locate the SM-3S properly, and keep it within effective radio range of the Base Unit.
4. Press the
Notes: 1) The LED starts flashing after a few seconds when smoke is detected,
then the internal buzzer sounds and activates the Base Unit after 10
seconds.
2) The LED flashes every 45 seconds to indicate the detector is in standby
mode, and it beeps periodically if the 9V battery goes too low. Replace
the battery when these beeps occur.
3) Maintenance at least once a year is essential. Open the cover and clean
the sensing chamber with a vacuum cleaner carefully.
4) The SM-3S comes with cover latches that prevent the cover from closing if no
battery is installed.
button, and check if the Base Unit is activated.
“TEST”
PREFERRED LOCATIONS
A
DINING ROOM BED
KITCHEN
ROOM
BED
ROOM
FAMILY ROOM
KITCHEN
LIVINGROOM
BED
ROOM
LIVING ROOM
z SMOKE DETECTORS FOR MINIMUM SECURITY
{ SMOKE DETECTORS FOR MORE SECURITY
Fig. 1: Locations for placing smoke
detectors for single residence with
only one sleeping area.
BEDROOM
BEDROOM
Fig. 2: Locations for placing smoke
detectors for single-floor residence
with more than one sleeping area.
SECURITY
SMOKE DETECTORS FOR MORE
SECURITY
³0.6m´
t least 0.6m
from the wall
LOCATIONS TO BE AVOIDED
Do
locate detector in:
NOT
The kitchen: Smoke from cooking might cause an unwanted alarm.
•
Near ventilating fan, fluorescent lamp or Air-Conditioning equipment: Air
•
drafts from them may affect the sensitivity of the detector.
Near ceiling beams or over cabinet: Stagnant air in these areas may affect the
•
sensitivity of the detector.
In the peak of an 'A' frame type of ceiling.
•
SPECIFICATIONS:
Detection: Photo-electric Chamber
Sensitivity: meets UL 217
Power: 9V alkaline battery
Temperature: 0℃ - 50℃
Relative Humidity: 10%～85%
Alarm Sound Level: 85dB@3m
Indicator Light: LED flashes every 45 seconds
Low Battery: Beep every 45 seconds
Current Drain: 6.5uA @standby, 24mA @activation
Battery Life: About 2 years.
Actuation Indicator: LED ON, Buzzer ON
Size: W 140mm x H 45mm
Weight: about 288g (w/ battery)
BED
ROOM
BED
ROOM
Loading...