PLEASE SAVE THIS OWNER’S MANUAL AND READ BEFORE EACH USE.
This manual will explain how to use the battery charger safely and effectively.
Please read and follow these instructions and precautions carefully.
NO USE EL CARGADOR DE BATERÍAS HASTA QUE HAYA LEÍDO Y COMPRENDIDO
COMPLETAMENTE EL MANUAL DEL USUARIO. Si usted desea una versión en español
de esta edición, visite nuestra página en la red localizada en www.batterychargers.com
así podrá obtener un instructivo del cargador de baterías en español. Si usted no tiene
acceso a la red y necesita asistencia, llame Servicios al Cliente al (800) 621-5485.
XP500
0099001228-01
Page 2
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ........................................................................3
PERSONAL SAFETY PRECAUTIONS...........................................................................3
FEATURES ..................................................................................................................... 4
CHARGING THE INTERNAL BATTERY OF THE INSTANT POWER ............................5
CHECKING THE INTERNAL BATTERY LEVEL .........................................................5
CHARGING THE INTERNAL BATTERY .....................................................................5
CHARGING THE INTERNAL BATTERY WHILE DRIVING .........................................5
USING THE INSTANT POWER ...................................................................................... 5
USING THE USB PORT .............................................................................................6
USING THE WORK LIGHT .........................................................................................6
POWERING A 12V DC DEVICE .................................................................................6
MAINTENANCE AND CARE .......................................................................................... 7
THIS UNIT CONTAINS A SEALED, NON-SPILLABLE LEAD-ACID
BATTERY. MUST BE DISPOSED OF PROPERLY.
WARNING: Possible explosion hazard. Contact with battery acid may
cause severe burns and blindness. Keep out of reach of children.
Page 3
IMPORTANT SAFETY INSTRUCTIONS
WARNING – RISK OF EXPLOSIVE GASES
WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES
GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. IT IS
IMPORTANT THAT YOU FOLLOW THESE INSTRUCTIONS EACH TIME YOU USE THE
INSTANT POWER.
To reduce risk of battery explosion, follow these instructions and those published by
battery manufacturer and manufacturer of any equipment you intend to use in vicinity
of battery. Review cautionary marking on these products and on engine.
WARNING: Pursuant to California
Proposition 65, this product contains
chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm. Wash hands after
handling.
• Keep out of reach of children.
• Do not disassemble the Instant Power.
Take it to a qualied service professional
if service or repair is required. Incorrect
assembly may result in re or electrical
shock.
• Do not use the Instant Power to jump a
vehicle while charging the internal battery.
• Do not recharge the Instant Power with a
damaged extension cord.
• The Instant Power gets hot during charging
and must have proper ventilation.
• Do not set the Instant Power on ammable
materials, such as carpeting, upholstery,
paper, cardboard, etc.
• Place the Instant Power as far away from
the battery being jumped as the cables
will permit.
• Do not expose the Instant Power to rain
or snow.
• Never place the Instant Power directly
above battery being jumped.
• To prevent arcing, never allow the clamps to
touch together or to contact the same piece
of metal.
• Use of an attachment not recommended or
sold by Schumacher® Electric Corporation
may result in damage to the unit or personal
injury.
• Never operate the Instant Power if it is
damaged.
• If someone else uses the Instant Power,
ensure they are well informed on how to
use it safely, and have read and understood
the operating instructions.
• The Instant Power is NOT designed to be
installed as a replacement for a vehicle
battery.
• Use ONLY on vehicles, boats and garden
tractors powered with a 12V DC battery
system.
• If the engine fails to start after the
recommended number of attempts,
disconnect the unit and look for other
problems that may need to be corrected.
• Use the Instant Power for jump starting
lead-acid batteries ONLY. Do not use for dry
cell batteries that are commonly used with
home appliances.
PERSONAL SAFETY PRECAUTIONS
• Wear complete eye and clothing protection
when working near lead-acid batteries.
Always have someone nearby for help.
• Have plenty of fresh water, soap and baking
soda nearby for use, in case battery acid
contacts your eyes, skin, or clothing. Wash
immediately with soap and water and seek
medical attention.
• If battery acid comes in contact with eyes,
ush eyes immediately for a minimum 10
minutes and get medical attention.
• Neutralize any acid spills thoroughly with
baking soda before attempting to clean up.
• Remove all personal metal items from your
body, such as rings, bracelets, necklaces
and watches. A battery can produce a short
circuit current high enough to weld a ring to
metal, causing a severe burn.
• Never smoke or allow a spark or ame in
the vicinity of the battery or engine.
• 3 •
Page 4
FEATURES
12
6
8
9
XP400
1. Battery status button
2. Battery status indicators
3. Built-in work light
4. Worklight ON/OFF switch
5. 12V DC power outlet
6. Battery clips
XP500
1. Battery status button
2. Rotary switch for USB and jump starter
3. Battery status indicators
4. Built-in work light
5. Worklight ON/OFF switch
6. 12V DC power outlet
7. USB port
8. Battery clips
XP750C
1. USB port
2. Battery status button
3. Rotary switch for USB and jump starter
4. Battery status indicators
5. Built-in work light
6. 12V DC power outlet
7. Worklight ON/OFF switch
8. Battery clips
9. Air compressor hose
10. Air compressor gauge
11. Air compressor ON/OFF switch
12. Internal battery charger plug
13. Air compressor hose wrap cleats
14. Air compressor adapters
and storage bag
3
2
1
3
2
1
4
3
2
1
14
4
5
4
5
6
8
7
5
6
7
10
11
13
• 4 •
It
Page 5
CHARGING THE INTERNAL BATTERY OF THE INSTANT POWER
IMPORTANT! CHARGE IMMEDIATELY
AFTER PURCHASE, AFTER EACH USE
AND EVERY 30 DAYS, TO KEEP THE
INSTANT POWER’S INTERNAL BATTERY
FULLY CHARGED. RECHARGING
BATTERY AFTER EACH USE WILL
PROLONG BATTERY LIFE.
CHECKING THE INTERNAL BATTERY
LEVEL
Press the Battery Status button on the
front of the unit. The LED lights will indicate
the charge level as follows:
RED indicates a 50% or less charge;
immediately charge the unit.
YELLOW indicates a 50% and higher
charge.
GREEN indicates the battery is fully charged.
CHARGING THE INTERNAL BATTERY
Charge the internal battery for the Instant
Power using an extension cord (not included).
NOTE: Use of an improper extension cord
could result in a risk of re and electric
shock.
1. Flip the AC connector on the back of the
unit up and plug in an 18 AWG or larger
extension cord.
2. Plug the extension cord into a 120V AC
electrical wall outlet.
3. The RED LED will light, indicating charging.
4. The GREEN LED will light when the
battery is fully charged. This could take up
to 72 hours. The charger will automatically
go into maintain mode and maintain the
battery at full charge without damaging it.
5. When charging is complete, unplug the
extension cord from the wall outlet and the
back of the unit.
CHARGING THE INTERNAL BATTERY
WHILE DRIVING
You may also charge the internal battery
while driving, using a male-to-male
charger cable (part number 94500109 –
not included).
IMPORTANT: DO NOT CHARGE
INTERNAL BATTERY FOR MORE THAN
30 MINUTES OR LEAVE THE BATTERY
UNATTENDED. IT COULD EXPLODE,
CAUSING PROPERTY DAMAGE OR
PERSONAL INJURY.
1. Make sure the car is running.
2. Insert one end of the accessory cable into
the 12V DC power outlet.
3. Insert the other end of the accessory
cable into the vehicle’s accessory outlet
(lighter socket).
NOTE: The RED and the GREEN LEDs do
not operate during this method of charging.
Using this method to charge the battery
overrides the maintain mode and the battery
can be overcharged.
4. Monitor the progress of the charge by
pressing the Battery Status button on
the front of the unit. When it reaches a full
charge, disconnect the accessory cable
from the Instant Power, then from the
lighter socket of the vehicle.
NOTE: Completely disconnect the charger
cable when the engine is not running.
USING THE INSTANT POWER
IMPORTANT: Using the Engine Start
feature without a battery installed in the
vehicle could cause damage to the vehicle’s
electric system.
1. Turn the ignition OFF before making the
cable connections.
2. Lay the DC cables away from any
fan blades, belts, pulleys and other
moving parts.
3. For a negative-ground vehicle (as in most
vehicles), connect the Instant Power’s
POSITIVE (RED) clamp to the POSITIVE
(POS, P, +) battery post. Next, connect
the NEGATIVE (BLACK) clamp to the
vehicle chassis or engine block, away
from the battery.
4. For a positive-ground vehicle, connect
the Instant Power’s NEGATIVE (BLACK)
clamp to the NEGATIVE (NEG, N, -)
battery post. Next, connect the POSITIVE
(RED) clamp to the vehicle chassis or
engine block away from the battery.
5. Turn the switch to the ON position (does
not apply to the XP400). Crank the
engine for no more than 8 seconds. If
the engine does not start, wait 2 minutes
before cranking again.
6. After the engine starts, turn the switch to
the OFF position and remove the clips from
the battery.
7. Charge the Instant Power as soon as
possible after use.
• 5 •
Page 6
USING THE USB PORT
(Models XP500 and XP750C)
The USB port provides up to 500mA
at 5V DC.
1. Ensure the battery clips are securely
clipped on the storage holders.
2. Turn the Instant Power ON.
3. Plug the device into the USB port.
4. Turn the USB device on.
5. When nished using the USB port, turn
the switch to the OFF position.
6. Charge the Instant Power as soon as
possible after using the USB port.
USING THE WORK LIGHT
The work light is controlled by a sliding ON/
OFF switch located on the front of the
Instant Power. Make sure the lamp is turned
OFF when the unit is being recharged or
stored. The lamp is efcient and will operate
up to 100 hours on a full charge.
Position the Instant Power on a at, stable
surface near the intended work area.
Ensure the battery clips are securely clipped
on the storage holders.
POWERING A 12V DC DEVICE
The Instant Power is a power source for all
12V DC accessories that are equipped with
a 12V accessory plug. Use it for power
outages and shing or camping trips.
NOTE: Do not power a 12V device with the
Instant Power while charging the internal
battery.
1. Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC
accessory outlet.
2. Open the protective cover of the DC power
outlet on the Instant Power.
3. Plug the 12V DC device into the DC
power outlet and turn on the 12V DC
device (if required).
4. When nished, turn off the DC device
(if required) and unplug from the DC
power outlet.
CAUTION: Do not use the Instant Power
to run appliances that draw more than
15A DC.
NOTE: Extended operation of a 12V DC
device may result in excessive battery
drain. Recharge the Instant Power
immediately after unplugging the 12V
DC device.
Estimated run-times
APPLIANCE
TYPE
Cell phone4 watts13 hrs19 hrs34 hrs
Fluorescent
light
Radios, fans9 watts6.7 hrs 9.3 hrs14 hrs
Depth nder9 watts6.7 hrs 9.3 hrs14 hrs
Camcorder15 watts4 hrs5.6 hrs7 hrs
Electrical tool 24 watts2.5 hrs3.5 hrs5 hrs
Electric
cooler
Car vacuum,
air compressor
NOTE: Actual time may vary. Times are based on the
internal battery being fully charged.
EST
WATTAGE
4 watts15 hrs21 hrs34 hrs
48 watts1.3 hrs 1.8 hrs 2 hours
80 watts0.8 hrs 1.1 hrs1.8 hrs
XP400XP500 XP750C
USING THE AIR COMPRESSOR
(model XP750C)
WARNING. Read the instructions of the
product being inated before using the
compressor. Avoid overination; do not
exceed the manufacturer’s recommended
pressures. Do not leave the air compressor
unattended during use.
NOTE: Before you use the compressor for
the rst time, you must install the
compressor hose wrap cleats. To install:
Press each cleat into its corresponding
mounting hole on the back of the jump
starter until it clicks into place.
Wrap the compressor hose around these
cleats when it is not being used.
1. Ensure the battery clips are securely on
the storage holders.
2. Remove the air compressor hose
from the storage cleats on the back of
the Instant Power. Install adapters as
necessary.
3. Attach the air compressor hose to the
product or accessory to be inated by
ipping down the lever.
4. Toggle the Compressor Switch up to the
ON position and inate the product.
5. When the product is inated to the proper
air pressure (using the air compressor
gauge), toggle the Compressor Switch
down to the OFF position and remove
the hose.
6. Do not run for more than 10 minutes
maximum at a time. Allow the Instant
Power to cool down for 10 minutes before
using again.
• 6 •
Page 7
NOTE: To prevent overheating, the
compressor has built-in thermal protection
that will turn the compressor off before it
overheats. If the compressor shuts off, wait
MAINTENANCE AND CARE
a few minutes and it will automatically
restart when the compressor cools.
NOTE: The air compressor is rated for
150 PSI.
A minimal amount of care can keep your
Instant Power working properly for years.
• Unplug the Instant Power before performing
any maintenance.
• Clean the clips and the case each time you
are nished using it.
• The Instant Power can be stored in any
position.
• Recharge the unit once a month when not
in use.
• Store clips on their support posts, to ensure
they do not come into contact with any
metallic surface.
TROUBLESHOOTING
PROBLEMPOSSIBLE CAUSEREASON/SOLUTION
The Instant Power won’t jump
start my car.
Clips are not making a good
connection to the battery.
Connections are reversed.
The Instant Power’s battery
is not charged.
• Never completely discharge the internal
battery.
Estimatedtimeforinating
Vehicle tires 13-16"6-24 minutes
Bike tires1-3 minutes
Sports balls30 seconds
These times are approximate, use the air compressor
gauge to ensure the proper pressure has been reached.
Do not overinate.
Check for poor connection to
battery and frame. Make sure
connection points are clean.
Disconnect the Instant Power
and reverse the clips.
Press the Battery Status button
on the front of the unit. The
LEDs will indicate the status of
charge.
The Instant Power won’t
power my 12V device.
The battery in the Instant
Power won’t hold a charge.
The vehicle’s battery is
defective.
Models XP500 and XP750C:
the Instant Power is not
turned on.
The 12V device is not
turned on.
The Instant Power’s battery
is not charged.
The 12V device draws more
than 15A or has a short
circuit.
The battery is bad (will not
accept a charge).
• 7 •
Have the battery checked.
Turn the Instant Power
ON/OFF switch to the ON
position.
Turn on the 12V device.
Check the battery charge
status by pressing the Battery
Status button.
Disconnect the 12V device.
The internal breaker will
automatically reset after a
minute or two. Try the 12V
device again.
For REPAIR OR RETURN, contact Customer Service at 1-800-621-5485.
DO NOT SHIP UNIT until you receive a RETURN MERCHANDISE AUTHORIZATION
(RMA) number from Customer Service at Schumacher Electric Corporation.
SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,
MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO THE
ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED WARRANTY
IS NOT TRANSFERABLE OR ASSIGNABLE.
Schumacher Electric Corporation (the “Manufacturer”) warrants this Instant Power for one
(1) year and the internal battery for ninety (90) days from the date of purchase at retail
against defective material or workmanship that may occur under normal use and care.
If your unit is not free from defective material or workmanship, Manufacturer’s obligation
under this warranty is solely to repair or replace your product, with a new or reconditioned
unit, at the option of the Manufacturer. It is the obligation of the purchaser to forward the
unit, along with proof of purchase and mailing charges prepaid to the Manufacturer or its
authorized representatives in order for repair or replacement to occur.
Manufacturer does not provide any warranty for any accessories used with this product
that are not manufactured by Schumacher Electric Corporation and approved for use
with this product. This Limited Warranty is void if the product is misused, subjected to
careless handling, repaired, or modied by anyone other than Manufacturer or if this
unit is resold through an unauthorized retailer.
Manufacturer makes no other warranties, including, but not limited to, express,
implied or statutory warranties, including without limitation, any implied warranty
of merchantability or implied warranty of tness for a particular purpose. Further,
Manufacturer shall not be liable for any incidental, special or consequential damage
claims incurred by purchasers, users or others associated with this product, including,
but not limited to, lost prots, revenues, anticipated sales, business opportunities,
goodwill, business interruption and any other injury or damage. Any and all such
warranties, other than the limited warranty included herein, are hereby expressly
disclaimed and excluded. Some states do not allow the exclusion or limitation of
incidental or consequential damages or length of implied warranty, so the above
limitations or exclusions may not apply to you. This warranty gives you specic legal
rights and it is possible you may have other rights which vary from this warranty.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND
THE MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO
ASSUME OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER
THAN THIS WARRANTY.
Schumacher® and the Schumacher Logo
are registered trademarks
of Schumacher Electric Corporation.
• 9 •
Page 10
• 10 •
Page 11
WARRANTY CARD
SAVE ON POSTAGE! ACTIVATE YOUR WARRANTY ONLINE –
THE QUICK AND EASY WAY!
Go to www.batterychargers.com to register your product online.
(No internet access? Send in the completed warranty card.)
REGISTRATION
1 YEAR LIMITED
WARRANTY PROGRAM
DO NOT SEND UNIT TO THIS ADDRESS FOR REPAIR.
This warranty is not transferable. Send warranty card only.
The warranty card should be submitted within 30 days of purchase. The customer