Schumacher IP-75 User Manual

Model / Modelo / Modèle : IP-75

Jump Starter and DC Power Source
Fuente de Poder de CD

y Arrancador
Aide de Démarrage

et Source d’Énergie CC

OWNER’S MANUAL

MANUAL DEL USUARIO

GUIDE D’UTILISATION

INSTANT POWER™

DO NOT RETURN THIS PRODUCT TO THE STORE!

Contact Customer Service for assistance:
Phone: [phone]
Email: [e-mail]
Web: www.batterychargers.com

¡NO LO DEVUELVA ESTE PRODUCTO A LA TIENDA!

Contacte Servicios al Cliente para asistencia:
Teléfono: 800-621-5485
Correo Electrónico: [e-mail]
Sitio Red: www.batterychargers.com

NE PAS RETOURNER LE PRODUIT AU MAGASIN!

Contactez le service clientéle pour l’aide :
Téléphone : 800-621-5485
E-mail : [e-mail]
Site web : www.batterychargers.com

READ THE ENTIRE MANUAL BEFORE USING THIS PRODUCT.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

LEA EL MANUAL COMPLETO ANTES DE UTILIZAR ESTE PRODUCTO.
CUALQUIER FALLA PODRÍA RESULTAR EN SERIAS LESIONES
O PODRÍA SER MORTAL.

LIRE ENTIÈREMENT LE GUIDE AVANT D’UTILISER CE PRODUIT.
L’ÉCHEC DE FAIRE AINSI PEUT S’ENSUIVRE DANS LA BLESSURE
SÉRIEUSE OU LA MORT.

0099001319-00

CONTAINS SEALED NON-SPILLABLE LEAD-ACID BATTERY.
MUST BE DISPOSED OF PROPERLY.

CONTIENE UNA BATERÍA SELLADA DE ÁCIDO-PLOMO NO
DERRAMABLE QUE DEBE DESECHARSE APROPIADAMENTE.

CONTIENT UNE BATTERIE À L’ACIDE QUI DOIT ÊTRE
DISPOSÉ CORRECTEMENT.

WARNING: Possible explosion hazard. Contact with battery acid may cause severe
burns and blindness. Keep out of reach of children.

ADVERTENCIA: Posible Riesgo de una explosión. El contacto con una batería de
ácido puede causar quemaduras y ceguera. Manténgase alejado de los niños.

AVERTISSEMENT : Hasard d’explosion possible. Contact avec l’acide de batterie
peut provoquer sévère brûle et la cécité. Ne le laissez pas a la portée des enfants.

IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.

SAVE THESE INSTRUCTIONS – This manual will show you how to use your charger

safely and effectively. Please read, understand and follow these instructions and
precautions carefully, as this manual contains important safety and operating instructions.
The safety messages used throughout this manual contain a signal word. The signal word
indicates the level of the hazard in a situation.

Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided, could result in
moderate or minor injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided, could result in
damage to the equipment, vehicle or property.

Pursuant to California Proposition 65, this product contains chemicals known to
the State of California to cause cancer and birth defects or other reproductive
harm. Wash hands after handling.

1. IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS.

This manual contains important safety and operating instructions.

RISK OF ELECTRIC SHOCK OR FIRE.

1.1 Read the entire manual before using this product. Failure to

do so could result in serious injury or death.

1.2 This Instant Power™ is not intended for use by persons
(including children) with reduced physical, sensory or mental

have been given supervision or instruction concerning the use of the Instant Power™
by a person responsible for their safety.

1.3 Children should be supervised, to ensure they do not play with the Instant Power™.

1.4 Do not put ngers or hands into the Instant Power™ clamps.

1.5 Do not expose the Instant Power™ to rain or snow.

1.6 Do not operate the Instant Power™ with damaged cables or clips; have the cable or clip

replaced immediately a qualied service person.

1.7 Do not operate the Instant Power™ if it has received a sharp blow, been dropped or

otherwise damaged in any way; take it to a qualied service person.

1.8 Do not disassemble the Instant Power™; take it to a qualied service person when service

or repair is required. Incorrect reassembly may result in a risk of re or electric shock.

capabilities, or lack of experience and knowledge, unless they

• 2 •

RISK OF EXPLOSIVE GASES.

1.9 WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS

DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST
IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU
USE THE INSTANT POWER™.

1.10 To reduce the risk of a battery explosion, follow these instructions and those published by

the battery manufacturer and the manufacturer of any equipment you intend to use in the
vicinity of the battery. Review the cautionary markings on these products and on the engine.

1.11 This Instant Power™ employs parts, such as circuit breakers, that tend to produce arcs and

sparks. If used in a garage, locate this Instant Power™ 18 inches (46 cm) or more above

oor level.

2. PERSONAL PRECAUTIONS
RISK OF EXPLOSIVE GASES. A SPARK NEAR

THE BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF A
SPARK NEAR THE BATTERY:

2.1 NEVER smoke or allow a spark or ame in the

vicinity of a battery or engine.

2.2 Remove personal metal items such as rings, bracelets, necklaces and watches when

working with a lead-acid battery. A lead-acid battery can produce a short-circuit current
high enough to weld a ring or the like to metal, causing a severe burn.

2.3 Be extra cautious, to reduce the risk of dropping a metal tool onto the battery. It might

spark or short-circuit the battery or other electrical part that may cause an explosion.

2.4 Do not permit the internal battery of the Instant Power™ to freeze. Never charge a

frozen battery.

2.5 To prevent sparking, NEVER allow clips to touch together or contact the same piece of metal.

2.6 Consider having someone nearby to come to your aid when you work near a lead-acid battery.

2.7 Have plenty of fresh water and soap nearby in case battery acid contacts your skin,

clothing or eyes.

2.8 Wear complete eye and body protection, including safety goggles and protective clothing.

Avoid touching your eyes while working near the battery.

2.9 If battery acid contacts your skin or clothing, immediately wash the area with soap and

water. If acid enters your eye, immediately ood the eye with cold running water for at

least 10 minutes and get medical attention right away.

2.10 If battery acid is accidentally swallowed, drink milk, the whites of eggs or water. DO NOT

induce vomiting. Seek medical attention immediately.

3. PREPARING TO USE THE INSTANT POWER™

RISK OF CONTACT WITH BATTERY ACID. BATTERY ACID IS A
HIGHLY CORROSIVE SULFURIC ACID.

3.1 Be sure the area around the battery is well ventilated while

the Instant Power™ is being used.

3.2 Clean the battery terminals before using the Instant Power™.

During cleaning, keep airborne corrosion from coming into contact
with your eyes, nose and mouth. Use baking soda and water to neutralize the battery acid
and help eliminate airborne corrosion. Do not touch your eyes, nose or mouth.

3.3 Determine the voltage of the battery by referring to the vehicle owner’s manual and make

sure that the output voltage of the Instant Power™ is correct.

3.4 Make sure that the Instant Power™ cable clips make tight connections.

• 3 •

4. CHARGER AND AC POWER CORD CONNECTIONS
RISK OF ELECTRIC SHOCK OR FIRE.

The Instant Power™ charger is for use on a nominal 120-volt
circuit. The plug must be plugged into an outlet that is properly
installed and grounded in accordance with all local codes and

ordinances. The plug pins must t the receptacle (outlet). Do not

use with an ungrounded system. NOTE: Pursuant to Canadian

Regulations, use of an adapter plug is not allowed in Canada. Use of an adapter plug in
the United States is not recommended and should not be used.

5. INSTALLATION INSTRUCTIONS

Remove all cord wraps and uncoil the cables prior to using the Instant Power™.

6. FEATU RES

1 2 3

1. Charged/Charging LEDs

2. Battery Status LEDs

3. Battery Status Button

4. 12V DC Power Outlet

(not shown)

7. CHARGING THE INTERNAL BATTERY OF THE INSTANT POWER™

IMPORTANT: CHARGE IMMEDIATELY AFTER PURCHASE, AFTER EACH USE
AND EVERY 30 DAYS TO KEEP THE INSTANT POWER™ INTERNAL BATTERY
FULLY CHARGED.

7.1 Use of an improper extension cord to charge the Instant Power™ could result in a risk of

re and electric shock. Make sure:

• That the pins on the plug of the extension cord are the same number, size and shape

as those of the plug on the Instant Power™.

• That the extension cord is properly wired and in good electrical condition.

• That the extension cord has a wire size of 18 gauge (AWG) [0.82 mm2] or larger and is

50 feet (15.24 meters) long or less.

7.2 To reduce the risk of electric shock, turn off and/or unplug the Instant Power™ before

attempting any maintenance or cleaning. Simply turning off the controls will not reduce
this risk.

7.3 When charging the internal battery, work in a well-ventilated area and do not restrict the

ventilation in any way.

7.4 LED Indicators:

To check the internal battery’s charge status, press the Battery Status button on the front
of the Instant Power™.

The LED lights will indicate the charge level as follows:

• A red LED indicates a 50% or less charge and you should immediately recharge
the Instant Power™.

• A yellow LED indicates a 50 to 75% charge. The Instant Power™ may be used but
should be recharged as soon as possible.

• A green LED indicates the internal battery is fully charged.

• The CHARGING (red) LED indicates the Instant Power™ is charging (connected

to an AC power source.) At full charge, the CHARGED (green) LED will light.

• 4 •

7.5 Charging the Internal Battery using the Built-In Charger:

1. To charge, plug an 18 gauge (AWG) [0.82 mm2] or larger extension cord into the

charger plug on the right side of the Instant Power™. (Extension cord not included;
must be purchased separately.)

2. Plug the extension cord into a 120V AC electrical wall outlet.

3. The CHARGING (red) LED will glow indicating charging.

4. The CHARGED (green) LED will light when the battery has reached full charge.

This could take up to 72 hours, depending on the age and condition of the battery.
The charger will automatically go into maintain mode and maintain the battery at full
charge without damaging it.

5. Charge the Instant Power™ as soon as possible after use.

NOTE: To reduce the risk of damage to the electric plug or cord, pull by the plug rather

than the cord when disconnecting the Instant Power™.
You may also charge the internal battery while driving, using the male-to-male charger

cable (p/n 94500109 – not included). Insert one end of the accessory cable into the 12V
DC power outlet and the other end into the vehicle’s accessory outlet (lighter socket).
Completely disconnect the charger cable when the engine is not running.

not operate during this method of charging. Using this method to charge the battery

The CHARGING (red) LED and the CHARGED (green) LED do

overrides the maintain mode and the battery can be overcharged. Monitor the progress of
the battery and when it reaches a full (100%) charge, disconnect the charger. Do not leave
the battery unattended or it could explode causing property damage or personal injury.

8. OPERATING INSTRUCTIONS

8.1 Jump Starting a Vehicle Engine
A SPARK NEAR THE BATTERY MAY CAUSE A

BATTERY EXPLOSION. TO REDUCE THE RISK
OF A SPARK NEAR THE BATTERY:

Do not use the Instant Power™ while charging the internal battery.

1. Turn the vehicle’s ignition OFF before making cable connections.

2. Position the DC cables to reduce the risk of damage by the hood, door and moving or

hot engine parts. NOTE: If it is necessary to close the hood during the jump starting
process, ensure that the hood does not touch the battery clips or cut the insulation of
the cables.

3. Stay clear of fan blades, belts, pulleys and other parts that can cause injury.

4. Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post usually

has a larger diameter than the NEGATIVE (NEG, N, -) post.

5. Determine which post of the battery is grounded (connected) to the chassis. If the

negative post is grounded to the chassis (as in most vehicles), see step 6. If the
positive post is grounded to the chassis, see step 7.

6. For a negative-grounded vehicle, connect the POSITIVE (RED) clip from the Instant

Power™ to the POSITIVE (POS, P, +) ungrounded post of the battery. Connect the
NEGATIVE (BLACK) clip to the vehicle chassis or engine block away from the battery.
Do not connect the clip to the carburetor, fuel lines or sheet-metal body parts. Connect
to a heavy gauge metal part of the frame or engine block.

7. For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clip from the Instant

Power™ to the NEGATIVE (NEG, N, -) ungrounded post of the battery. Connect the
POSITIVE (RED) clip to the vehicle chassis or engine block away from the battery. Do
not connect the clip to the carburetor, fuel lines or sheet-metal body parts. Connect to
a heavy gauge metal part of the frame or engine block.

If you have connected the clips backwards, an audio alarm will sound.
Reverse the connections and the audio alarm will stop.

8. Crank the engine. If the engine does not start within 5-8 seconds, stop cranking and

wait at least 1 minute before attempting to start the vehicle again. (This permits the
Instant Power™ battery to cool down.)

• 5 •

9. After the engine starts, immediately disconnect the clip from the vehicle chassis and

then the remove the clip from the battery terminal in that order and clip them back
onto the Instant Power™ storage holders.

10. Recharge the Instant Power™ as soon as possible after use.
RISK OF EXPLOSION.

To prevent sparking, NEVER allow the clips to touch together or to contact the
same piece of metal. Never attempt to jump start a frozen battery.

8.2 Powering a 12V DC Device:

The Instant Power™ is a power source for all 12V DC accessories that are

equipped with a 12V accessory plug. Use it for power outages and shing or

camping trips.

Make sure the device to be powered is OFF before inserting the 12V DC accessory plug
into the 12V DC accessory outlet.

1. Ensure the battery clips are securely on the storage holders.

NOTE: The clips on the Instant Power™ are live and will produce arcing or sparking if

they come in contact with each other. To prevent accidental arcing, always keep the clips
on the storage holders when not using them to jump start a vehicle.

2. Open the protective cover of the DC power outlet on the back of the Instant Power™.

3. Plug the 12V DC device into the DC power outlet, and turn the 12V DC device on (if

required).

4. If the 12V DC device draws more than 15A or has a short circuit, the internal fuse of

the Instant Power™ will blow and disconnect the power to the device. If this occurs, the

fuse must be replaced by a qualied service person. Unplug the device. The blown fuse

only affects the 12V DC socket.

The DC power outlet is wired directly to the internal battery. Extended
operation of a 12V DC device may result in excessive battery drain.
Recharge immediately after unplugging the 12V DC device.

9. MAINTENANCE INSTRUCTIONS

9.1 After use and before performing maintenance, unplug and disconnect the Instant Power™

(see sections 3 and 4).

9.2 Use a dry cloth to wipe all battery corrosion and other dirt or oil from the battery clips,

cords, and the Instant Power™ case.

9.3 Ensure that all of the Instant Power™ components are in place and in good working

condition, including the plastic boots on the battery clips.

9.4 Servicing does not require opening the unit, as there are no user-serviceable parts. All

servicing should be performed by qualied service personnel.

10. MOVING AND STORAGE INSTRUCTIONS

10.1 Store the Instant Power™ in an upright position.

10.2 Store inside, in a cool, dry place.

10.3 Do not store the clips on the handle, clipped together, on or around metal, or clipped to

cables. The clips on the Instant Power™ are live and will produce arcing or sparking if
they come in contact with each other. To prevent accidental arcing, always keep the clips
on the storage holders when not using them to jump start a vehicle.

10.4 If the Instant Power™ is moved around the shop or transported to another location, take

care to avoid/prevent damage to the cords, clips and Instant Power™. Failure to do so
could result in personal injury or property damage.

Do not use and/or store the Instant Power™ in or on any area or surface
where damage could occur if the internal battery should unexpectedly
leak acid.

10.5 IMPORTANT:

•CHARGE IMMEDIATELY AFTER PURCHASE

•KEEP FULLY CHARGED

Charge the Instant Power™ internal battery immediately after purchase, after every use
and every 30 days.

• 6 •

All batteries are affected by temperature. The ideal storage temperature is at 70° F. The
internal battery will gradually self-discharge (lose power) over time, especially in warm
environments. Leaving the battery in a discharged state may result in permanent battery
damage. To ensure satisfactory performance and avoid permanent damage, charge the
internal battery every month.

11. TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE REASON/SOLUTION

The Instant Power™
won’t jump start my car.

Clips are not making a
good connection to the
battery.

Check for poor connection to
battery and frame. Make sure
connection points are clean. Rock
clips back and forth for a better
connection.

Connections are reversed.

Disconnect the Instant Power™ and
reverse the clips.

The Instant Power™
battery is not charged.

Check the battery charge status
by pressing the button on the front
of the Instant Power™. See LED
Indicators section of this manual.

The vehicle’s battery is

Have the battery checked.

defective.

The Instant Power™
won’t power my 12V

The 12V device is not
turned on.

Turn on the 12V device.

device.

The Instant Power™
battery is not charged.

Check the battery charge status
by pressing the button on the front
of the Instant Power™. See LED
Indicators section of this manual.

The battery in the Instant
Power™ won’t hold a

The 12V device draws
more than 15A or has a
short circuit

The battery is bad (will not
accept a charge).

Disconnect the 12V device and try
again. If it happens again, replace
the 12V device.

Have the battery checked.

charge.

12. BEFORE RETURNING FOR REPAIRS

When an UNKNOWN OPERATING PROBLEM arises, please read the complete manual
and call the customer service number for information. This will usually eliminate the need
for return.

If these solutions do not eliminate the problem, or for information

about troubleshooting, call toll-free from anywhere in the U.S.A.

1-800-621-5485

7:00 am to 5:00 pm Central Time, Monday through Friday

For REPAIR OR RETURN, contact Customer Service at 1-800-621-5485.

DO NOT SHIP UNIT until you receive a RETURN MERCHANDISE AUTHORIZATION
(RMA) number from Customer Service at Schumacher Electric Corporation.

• 7 •

13. LIMITED WARRANTY
SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,

MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO THE
ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED WARRANTY
IS NOT TRANSFERABLE OR ASSIGNABLE.

Schumacher Electric Corporation (the “Manufacturer”) warrants this Instant Power™
for one (1) year and the internal battery for ninety (90) days from the date of purchase
at retail against defective material or workmanship that may occur under normal use
and care. If your unit is not free from defective material or workmanship, Manufacturer’s
obligation under this warranty is solely to repair or replace your product, with a new or
reconditioned unit, at the option of the Manufacturer. It is the obligation of the purchaser
to forward the unit, along with proof of purchase and mailing charges prepaid to the
Manufacturer or its authorized representatives in order for repair or replacement to occur.

Manufacturer does not provide any warranty for any accessories used with this product
that are not manufactured by Schumacher Electric Corporation and approved for use with
this product. This Limited Warranty is void if the product is misused, subjected to careless

handling, repaired, or modied by anyone other than Manufacturer or if this unit is resold

through an unauthorized retailer.
Manufacturer makes no other warranties, including, but not limited to, express, implied or

statutory warranties, including without limitation, any implied warranty of merchantability or

implied warranty of tness for a particular purpose. Further, Manufacturer shall not be liable

for any incidental, special or consequential damage claims incurred by purchasers, users

or others associated with this product, including, but not limited to, lost prots, revenues,

anticipated sales, business opportunities, goodwill, business interruption and any other
injury or damage. Any and all such warranties, other than the limited warranty included
herein, are hereby expressly disclaimed and excluded. Some states do not allow the
exclusion or limitation of incidental or consequential damages or length of implied warranty,

so the above limitations or exclusions may not apply to you. This warranty gives you specic

legal rights and it is possible you may have other rights which vary from this warranty.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND THE
MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO ASSUME OR
MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER THAN THIS
WARRANTY.

Schumacher Electric Corporation Customer Service

Monday – Friday 7:00 a.m. to 5:00 p.m. CST

Schumacher® and the Schumacher Logo are registered trademarks

of Schumacher Electric Corporation.

1-800-621-5485

DO NOT RETURN THIS PRODUCT TO THE STORE!

Contact Customer Service for assistance:
Phone: [phone]
Email: [e-mail]
Web: www.batterychargers.com

• 8 •