Schumacher IP-1875C User Manual

Schumacher Electric Corporation

OWNER’S MANUAL

INSTANT POWER™ Jump Starter, Air Compressor &

12V DC Power Source

THIS PRODUCT HAS A SEALED LEAD-ACID BATTERY INSIDE THAT SHOULD BE KEPT AT FULL CHARGE FOR LONGER LIFE.

RECHARGE WHEN FIRST RECEIVED (EVEN IF GREEN ‘FULL POWER’ LED GLOWS), AFTER EACH USE AND EVERY 3 MONTHS.

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions

important safety instructions

Someone should be within range of your voice or close enough to
come to your aid when you are working near a lead-acid battery.

Have plenty of fresh water and soap nearby in case battery acid
contacts skin, clothing, or eyes. If acid enters the eye area, rinse
with cold water for at least 10 minutes and get medical help
immediately.

Do not smoke, or use matches or cigarette lighter, or allow any spark

or ame near the battery or engine.

Never operate the power source unit if it has damaged lead wire or

clamps. Have the lead wire replaced by a qualied technician.

Wear complete eye and clothing protection when working with lead­acid batteries.

Do not permit the internal battery of the IP-1875C to freeze. Never
charge a frozen battery.

handling warning

WARNING: Handling the cord on this product or cords associated with
this product, may expose you to lead, a chemical known to the State
of California to cause cancer and birth defects or other reproductive
harm. Wash hands after handling.

operating instructions

War ning: Failure to follow instructions may cause
damage or an explosion. Read entire instruction manual
before use.

1. Turn ignition OFF before making cable connections.

2. Use in a well-ventilated area.

3. Keep clears of fan blades, belts, pulleys and other parts that may
cause injury.

4. Make sure the power ON/OFF switch is in the OFF position until
clamps are connected to the vehicle battery.

5. NEVER allow clamps to touch together or to contact the same
piece of metal to prevent sparking.

6. Clamp the red clamp (+) to the positive terminal of the battery.
(For a negative grounded system.)*

7. Clamp the black clamp (-) to an unpainted and unmoving part of
the chassis or engine block.

8. If you have connected the clamps of your IP-1875C backwards,
an audio alarm will sound. DO NOT turn your IP-1875C on. This
could cause serious damage. Reverse the connections, and the
audio alarm will stop.

9. If no audio alarm is sounded, turn ON the Jump Start switch
and then crank the engine. If the engine does not start within
5-8 seconds, wait at least 1 minute before attempting to start
vehicle again. (This permits the battery to cool down.)

10. After the engine starts, make sure to turn OFF the Jump Start
switch. Then disconnect the black clamp (-) and then the red
clamp (+) in that order. Store the clamps on the ears located on
the sides of the case.

11. Recharge the IP-1875C as soon as possible after use.

*NOTE: In the rare case of jump-starting a vehicle that has

a positive-grounded vehicle electrical system, connect the
NEGATIVE black clamp (-) to the negative terminal (-) of the
vehicle battery. Then connect the POSITIVE red clamp (+) to an
unpainted and unmoving part of the vehicle chassis or engine
block. If you are unsure of the nature of the vehicle’s electrical
grounding system, check the owner’s manual of the vehicle. To
disconnect clamps, reverse order.

led indicators

To check the internal battery’s charge status, press the red button
on the front of the IP-1875C.

The LED lights will indicate the charge level as follows:

1. A red LED indicates a 50% or less charge and you should
immediately recharge the IP-1875C.

2. A yellow LED indicates a 50 to 75% charge. The IP-1875C may
be used but should be recharged as soon as possible.

3. A green LED indicates the internal battery is fully charged.

charging of internal battery with built-in charger.
After removing the IP-1875C from the carton, charge it for a minimum

of 8 hours before using even if the green charged LED glows.
NOTE: The ON/OFF switch does not have to be in the ON position

to recharge the internal battery.

1. To charge, plug an extension cord into charger plug on the back
of the IP-1875C. (Extension cord not included; must be purchased
separately.)

2. Plug the extension cord into 110V AC electrical wall outlet.

3. The red LED will glow indicating charging.

4. The green LED will glow when the battery has reached full
charge. This could take up to 72 hours on some charges due to
age and condition of the battery. The charger will automatically

drop into a oat mode and maintain the battery at full charge

without damaging the battery. The IP-1875C can be left plugged

into the 110V wall outlet indenitely to maintain full power.

5. Recharge the IP-1875C as soon as possible after use.

using the white spotlight

The spotlight is located on the front panel of the IP-1875C. This light
can be adjusted downward by pulling the tab at the top. The control
switch for this light is located above the rotary switch On/Off.

12 Volt dc power outlet chart

The IP-1875C is a power source for all 12 volt DC accessories
equipped with a 12 volt accessory plug. Make sure the device to be
powered is OFF before inserting 12 volt accessory plug into 12 volt

DC accessory outlet. Use for power outages, shing, and camping

trips. Estimated usage time is listed in below chart.

Appliance Type Estimated Wattage Estimated Time*
Cell Phones 4 Watts 30 Hours

Fluorescent Lights 4 Watts 30 Hours
Radios, Fans 9 Watts 21 Hours
Depth Finders 9 Watts 21 Hours

Model IP-1875C

00-99-000675/1106

Appliance Type Estimated Wattage Estimated Time*
Camcorders, VCRs 15 Watts 12 Hours

Electrical Tools 24 Watts 7 Hours
Electrical Coolers 48 Watts 3 Hours

The DC socket has a 30 amp automatic overload protection circuit
breaker. If overload occurs, reset the breaker by pushing the breaker
button located on the back of the IP-1875C.

110 Volt ac power source chart

(Inverter {Not Included} Is Necessary)

When using with an inverter, it can operate appliances normally
powered by 110V AC.

Appliance Type Estimated Wattage Estimated Time*
Spot Lights,

Sump Pumps 100 Watts 1.5 Hours
Faxes, TVs,

Small Power Tools 150 Watts 1 Hour
Computers, Printers,

Medium Power Tools,
Blenders 200 Watts 45 Minutes

When the IP-1875C is used with an inverter, it can operate appliances
normally power by 110V AC. Inverter not included; must be purchased
separately.

*NOTE: Estimated time is conservatively reported. Actual time may
vary. Times are based on the IP-1875C having a full charge. Requires
the use of an inverter that is not included. Designed for up to a 300
watt inverter.

using the air compressor

PRECAUTION – Read instructions of the product being inated
before using the compressor. Avoid over ination, do not exceed

the manufacturers recommended pressures. DO NOT leave the
compressor unattended during use.

The 12 volt compressor is rated for 280 PSI pressure. The hose is
stored in the back compartment of your IP-1875C. The ON / OFF
switch for the compressor is located on the back of the IP-1875C
below the charger plug.

1. There are three nozzles to inate products. Use appropriate

nozzle.

2. To inate a tire, unscrew the valve stem cap from the tire.

3. Attach the nozzle of the compressor hose and thread or latch
onto the product stem until it is secure.

4. To start the air compressor, push the switch located on the back
of the IP-1875C to ON.

5. Inate product and when the product is inated to the proper air

pressure, push the switch to OFF.

NOTE: The air compressor will run for a maximum of 15 minutes

or it may automatically shut down sooner if a high load causes it
to overheat. It will then cool for 10 minutes. After 10 minutes, the
air compressor will automatically restart.

Estimated time for inating

Vehicle 13" to 16" 3 to 16 minutes
Bike tire 30 to 40 seconds
Balls 5 to 30 seconds
Use a gauge to ensure the proper pressure has been reached. Do

not over inate.

storage

The IP-1875C can be stored in any position. When the IP-1875C is ON,
the clamps are live and will produce arcing or sparking if they come
in contact with each other. To prevent accidental arcing, always keep
the clamps on the side ears and the JUMP START ON/OFF switch in
the OFF position when not using it to jump start a vehicle.

All batteries are affected by temperature. The ideal storage
temperature is at 70 degrees Fahrenheit. Performance varies based
on battery temperature conditions.

limited warranty

Schumacher Electric Corporation warrants your unit to be free from defects in material and workmanship, excepting abuse or misuse, for a period of one year

from the date of sale to the original user or consumer purchaser. If your unit fails or malfunctions within the rst 30 days of the warranty, we will replace it with a

new unit. If your unit malfunctions or fails within the 12 month warranty period because of a defect in material or workmanship, we will repair without charge.
The internal battery, excluding units with swollen batteries or melted battery terminals, carries a 90-day warranty from the date of purchase. Proof of purchase

required. All battery replacements will be at the sole discretion of the manufacturer or his designated agents.
This warranty is in lieu of all other express warranties. The duration of any implied warranty, including but not limited to any implied warranty of merchantability

or tness for a particular purpose, made in respect to your unit is limited to the period of the express warranty set forth above.

For warranty service, return your product, with proof of purchase, to the factory or a designated agent: Schumacher Electric Corporation Warranty Ser vice
Department, 1025 E. Thompson Street, PO Box 280, Hoopeston, IL 60942. Phone [phone], Customer Service hours: 7 AM to 4:30 PM CST.

You will be responsible for all insurance and freight or other transportation charges to the factor y or point of repair. We will return your unit freight prepaid if
repair is covered under warranty. Your unit should be properly packed to avoid damage in transit, since we will not be responsible for any such damage.

In no event shall Schumacher Electric Corporation be liable for consequential or incidental damages. Some states do not allow limitations on the length of
the implied warranty or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This

warranty gives you specic legal rights and you may also have other rights which vary from state to state.

CONTAINS SEALED LEAD-ACID BATTERY. MUST BE DISPOSED
OF PROPERLY.

WARNING: Possible explosion hazard. Contact with battery acid may
cause severe burns and blindness. Keep out of reach of children.

801 Business Center Drive, Mount Prospect, IL 60056-2179

Send Warranty Product Repairs to: Schumacher Electric Corporation

1025 East Thompson, Hoopeston, IL 60942-0280

Call Customer Service if you have questions: 1-800-621-5485 (Hours: 7 a.m. – 4:30 p.m. CST)

Schumacher Electric Corporation

Modèle IP-1875C

GUIDE DE L’UTILISATEUR

Aide-démarrage, compresseur d’air et source

d’alimentation CC INSTANT POWER™

UNE BATTERIE SCELLÉE, AU PLOMB-ACIDE, EST INCORPORÉE À CE PRODUIT. ON DOIT LA MAINTENIR COMPLÈTEMENT CHARGÉE

POUR QU’ELLE DURE PLUS LONGTEMPS. RECHARGEZ-LA DÈS QUE VOUS EN PRENEZ POSSESSION (MÊME SI LE VOYANT VERT

« ENTIÈREMENT CHARGÉE » EST ALLUMÉ), APRÈS CHAQUE USAGE ET À TOUS LES 3 MOIS.

INSTRUCTIONS IMPORTANTES RELATIVES À LA SÉCURITÉ

Conservez ces instructions.

INSTRUCTIONS IMPORTANTES

RELATIVES À LA SÉCURITÉ

Quelqu’un doit être assez près pour vous venir en aide ou pour
entendre vos cris d’appel quand vous travaillez à proximité d’une
batterie au plomb-acide.

Ayez beaucoup d’eau fraîche et du savon à la portée de la main au
cas où de l’acide de batterie viendrait en contact avec la peau, les
vêtements ou les yeux. Si l’acide vient en contact avec les yeux,
rincez-les à l’eau froide pendant au moins 10 minutes et obtenez
immédiatement des soins médicaux.

Ne fumez pas, n’utilisez pas d’allumettes ni de briquet à proximité
d’une batterie ou d’un moteur et ne permettez pas qu’il y ait des

étincelles ou des ammes.
Ne faites jamais fonctionner la source d’alimentation si ses ls

électriques ou ses pinces sont endommagés. Demandez à un

technicien qualié de remplacer le l électrique.

Portez des lunettes de sûreté et des vêtements protecteurs quand
vous manipulez des batteries au plomb-acide.

Veillez à ce que la batterie interne ne gèle pas. Ne tentez jamais de
recharger une batterie gelée.

AVERTISSEMENT RELATIF À LA MANIPULATION

ATTENTION : La manipulation du cordon de ce produit ou des
cordons associés à ce produit peut vous exposer au plomb, un produit
chimique reconnu, par l’État de la Californie, pour causer le cancer
ainsi que des anomalies congénitales ou autre dommage génétique.

Il faut se laver les mains après la manipulation.

INSTRUCTIONS DE FONCTIONNEMENT

Attention : Le fait de ne pas suivre les instructions peut
causer des dommages ou produire une explosion. Lisez
le manuel d’instructions en entier avant l’utilisation.

1. Coupez le contact du véhicule avant d’effectuer le raccordement
des câbles.

2. Assurez-vous que l’interrupteur de l’aide-démarrage est fermé
(OFF) tant que les pinces ne sont pas raccordées à la batterie
du véhicule.

3. Utilisez dans un endroit bien aéré.

4. Tenez-vous à l’écart des pales de ventilateur, courroies, poulies
et de toute pièce posant un risque de blessure.

5. Les pinces ne doivent jamais se toucher ni toucher à la même
pièce de métal pour éviter que des étincelles ne se produisent.

6. Fixez la pince rouge (+) à la borne positive de la batterie. (S’il
s’agit d’un système à masse négative.)*

7. Fixez la pince noire (-) à une pièce métallique xe du châssis ou

du bloc moteur.

8. Si vous avez inversé les pinces de votre source d’alimentation
IP-1875C lor s du raccordement, l’aver tisseur sonore se

déclenchera. N’ouvrez PAS l’interrupteur de l’appareil (ON). De
graves dommages pourraient en résulter. Inversez les pinces et
l’avertisseur sonore cessera de se faire entendre.

9. Si vous n’entendez pas l’alarme, mettez l’interrupteur marche/
arrêt de l’aide de démarrage en position de marche (ON) puis
démarrez le moteur. Si le moteur ne démarre pas, dans 5 – 8
secondes, arrêtez et attendez au moins 1 minute avant d’essayer
à nouveau. (Ceci permettra à la batterie de refroidir.)

10. Après le démarrage du moteur, débranchez d’abord la pince noire
(-), puisla pince rouge (+), dans cet ordre. Rangez les pinces sur
les oreilles situées de part et d’autre du boîtier.

11. Rechargez l’appareil modèle IP-1875C dès que possible après
l’avoir utilisé.

*REMARQUE : Dans les rares cas où le démarrage d’urgence

doit être effectué sur un véhicule dont le système électrique est
à masse positive, raccordez la pince noire NÉGATIVE (-) à la
borne négative de la batterie du véhicule. Raccordez ensuite

la pince rouge POSITIVE (+) à une pièce non peinte et xe du

châssis ou du bloc moteur du véhicule. Si vous ne savez pas
de quel type de système de mise à la masse électrique est doté
le véhicule, consultez le guide de l’utilisateur du véhicule. Pour
débrancher les pinces, procédez dans l’ordre inverse.

VOYANTS

Pour vérier l’état de la batterie interne, appuyez sur le bouton rouge

situé sur le devant de l’appareil modèle IP-1875C.
Les voyants vont indiquer ce qui suit :

1. Le voyant rouge indique que la charge de la batterie interne est
de 50 % ou moins ; vous devez alors recharger immédiatement
l’appareil.

2. Le voyant jaune indique que la charge de la batterie interne se
situe entre 50 et 75 %. On peut utiliser l’appareil modèle IP­1875C, mais il faudra le recharger dès que possible.

3. Le voyant vert indique que la batterie interne est entièrement
chargée.

CHARGE de la batterie interne à l’aide du chargeur intégré.
Après avoir sorti l’appareil modèle IP-1875C de sa boîte, chargez-le

durant la nuit ou pendant 8 heures au moins avant de l’utiliser, même
si le voyant LED vert est allumé.

REMARQUE : Il n’est pas nécessaire que l’interrupteur soit ouvert
(ON) pour recharger la batterie interne.

1. Pour charger, branchez une rallonge dans la prise de chargeur à
l’arrière de l’appareil modèle IP-1875C. (Rallonge non incluse ;
doit être achetée séparément.)

2. Branchez la rallonge dans une prise électrique de 110 V CA.

3. Le voyant rouge EN COURS DE CHARGE est allumé durant la
charge.

00-99-000675/1106