• 6 •
USING THE USB PORT
(Models XP500-CA and XP750C-CA)
The USB port provides up to 2A
at 5V DC.
1. Ensure the battery clamps are securely
clipped on the storage holders.
2. Turn the Instant Power ON.
3. Plug your device into the USB port.
4. When nished using the USB port, turn
the switch to the OFF position.
5. Charge the Instant Power.
USING THE WORK LIGHT
The work light is controlled by a sliding ON/
OFF switch located on the front of the Instant
Power. Make sure the lamp is turned OFF
when the unit is being recharged or stored.
Position the Instant Power on a at, stable
surface near the intended work area.
Ensure the battery clamps are securely
clipped on the storage holders.
POWERING A 12V DC DEVICE
The Instant Power is a power source for all
12V DC accessories that are equipped with
a 12V accessory plug. Use it for power
outages and on shing or camping trips.
NOTE: Do not power a 12V device with the
Instant Power while charging the internal
battery.
1. Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC
accessory outlet.
2. Open the protective cover of the DC power
outlet on the Instant Power.
3. Plug the 12V DC device into the DC
power outlet and turn on the 12V DC
device (if required).
4. When nished, turn off the DC device
(if required) and unplug from the DC
power outlet.
CAUTION: Do not use the Instant Power
to run appliances that draw more than
15A DC.
NOTE: Extended operation of a 12V DC
device may result in excessive battery
drain. Recharge the Instant Power
immediately after unplugging the 12V
DC device.
USING THE AIR COMPRESSOR
(Model XP750C-CA)
WARNING. Read the instructions of the
product being inated before using the
compressor. Avoid overination; do not
exceed the manufacturer’s recommended
pressures. Do not leave the air compressor
unattended during use.
NOTE: Before you use the compressor for
the rst time, you must install the
compressor hose wrap cleats. To install:
press each cleat into its corresponding
mounting hole on the back of the jump
starter until it clicks into place.
Wrap the compressor hose around these
cleats when it is not being used.
1. Remove the air compressor hose from
the storage cleats.
2. Connect the adaptor to the valve stem
and close the thumb latch. If necessary,
use one of the additional adaptors.
3. Turn ON the inator power switch and
inate to the desired pressure or fullness.
4. When the desired pressure is reached,
put the inator power switch to OFF,
open the thumb latch and remove the
connector from the valve stem.
5. Allow unit to cool.
6. Recharge the unit before storing.
NOTE: The air compressor is rated for
150 PSI.
Estimated run-times
APPLIANCE
TYPE
EST
WATTAGE
XP400-CA XP500-CA
XP750C-CA
Cell phone 4 watts 13 hrs 19 hrs 34 hrs
Fluorescent
light
4 watts 15 hrs 21 hrs 34 hrs
Radios, fans 9 watts 6.7 hrs 9.3 hrs 14 hrs
Depth nder 9 watts 6.7 hrs 9.3 hrs 14 hrs
Camcorder 15 watts 4 hrs 5.6 hrs 7 hrs
Electrical tool 24 watts 2.5 hrs 3.5 hrs 5 hrs
Electric
cooler
48 watts 1.3 hrs 1.8 hrs 2 hours
Car vacuum,
air compressor
80 watts 0.8 hrs 1.1 hrs 1.8 hrs
NOTE: Actual time may vary. Times are based on the
internal battery being fully charged.