Schumacher 85-716 User Manual

Model 85-716
Professional Racing Battery Charger Fully Automatic For 16V AGM Batteries
16 Volts 25 Amps
INSTRUCTION MANUAL
English ................................................. p. 1
Français ................................................. p. 13
Español ................................................. p. 29
IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.
KEEP IT WITH OR NEAR THE CHARGER AT ALL TIMES.
1. IMPORTANT SAFETY INSTRUCTIONS
WARNING—RISK OF EXPLOSIVE GASES
1.1 WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION, AND WHEN DISCHARGED OR CHARGED. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE SAFETY AND OPERATING INSTRUCTIONS EXACTLY.
1.2 To reduce risk of battery explosion, follow these safety instructions and those published by the battery manufacturer and the manufacturer of any equipment you intend to use in the vicinity of a battery. Review cautionary markings on these products and on engine, and on vehicle or equipment containing the battery.
1.3 CAUTION: To reduce the risk of injury, charge only rechargeable
LEAD-ACID-TYPE batteries which may include MAINTENANCE-FREE, LOW-MAINTENANCE OR DEEP CYCLE batteries. Other types of batteries may burst causing personal injury and damage.
If you are uncertain as to the type of battery you are attempting to charge,
or the correct procedure for checking the battery’s state of charge, contact the seller or battery manufacturer.
1.4 Use of an attachment not recommended or sold by the battery charger
manufacturer may result in a risk of re, electric shock, or injury to persons.
1.5 To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the charger.
1.6 Position the AC and DC leads to avoid tripping over them and to prevent damage by the vehicle hood, doors, or moving engine parts; protect the leads from heat, oil, and sharp edges.
1.7 Do not operate the charger if it has received a sharp blow, been dropped,
or otherwise damaged in any way; take it to a qualied service center.
1.8 Do not disassemble the charger; take it to a qualied service center when
repair is required. Incorrect reassembly may result in a risk of electric
shock or re.
The charger is not intended to supply power to a low-voltage electrical
system other than applications using rechargeable, lead-acid type batteries. Do not use the battery charger to charge dry-cell batteries used with home appliances. These batteries may burst and cause personal
injury or property damage.
1
1.9 NEVER charge a frozen battery. Thaw it out rst. Charging will then be
safer and more efcient.
1.10 To reduce risk of electric shock, unplug the charger from the AC outlet before attempting any maintenance or cleaning. Turning off the controls will not reduce this risk.
1.11 Boat batteries must be removed and charged on shore. To safely
charge them onboard requires equipment especially designed and UL Listed for marine use.
1.12 Connect and disconnect the battery leads only when the AC supply cord is disconnected.
1.13 Do not overcharge the battery.
1.14 When charging a battery, charge it in a dry, well-ventilated area.
1.15 Never place articles on or around the charger. Never locate the charger in
a way that will restrict the ow of cooling air through the cabinet.
1.16 An extension cord should not be used unless absolutely necessary. (See paragraph 4.3.)
1.17 WARNING: THIS EQUIPMENT EMPLOYS PARTS, SUCH AS SWITCHES
AND CIRCUIT BREAKERS, THAT CAN PRODUCE ARCS OR SPARKS. LOCATE THE CHARGER AT LEAST 46 CM (18 INCHES) ABOVE GROUND LEVEL. IF USED IN A GARAGE, LOCATE IN A ROOM OR ENCLOSURE PROVIDED FOR THE PURPOSE, AND NOT LESS THAN 46 CM (18 INCHES) ABOVE FLOOR LEVEL.
1.18 WARNING: Handling the cord on this product or cords associated with accessories sold with this product, may expose you to lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
1.19 Have a damaged cord or plug replaced immediately.
1.20 Do not expose the charger to rain or snow.
2
2. PERSONAL PRECAUTIONS
2.1 Always have someone within range of your voice or close enough to come to your aid, when working around lead-acid batteries.
2.2 Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
2.3 Wear complete eye protection, clothing protection, and rubber soled shoes. When the ground is very wet or covered with snow, wear rubber boots. Avoid touching eyes while working near the battery.
2.4 If battery acid contacts skin or clothing, wash immediately with soap and
water. If acid enters the eyes, immediately ush with running cold water for
at least 10 minutes and seek medical attention.
2.5 NEVER smoke or allow a spark or ame in vicinity of the battery or engine.
2.6 Be extra cautious to reduce risk of dropping a metal tool onto the battery. It might spark or short circuit the battery or other electrical part that may cause an explosion.
2.7 Before working with a lead acid battery, remove personal metal items such as rings, bracelets, necklaces, watches, etc. A lead acid battery can produce a short circuit current high enough to weld such items, causing a severe burn.
3. PREPARING TO CHARGE BATTERY
3.1 If necessary to remove the battery from the vehicle to charge, always
remove the grounded terminal from battery rst. Make sure all accessories
in the vehicle are off to prevent a possible arc.
3.2 Be sure the area around the battery is well ventilated while the battery is being charged. Gas can be forcefully blown away by using a piece of cardboard or other nonmetallic material as a fan.
3.3 Clean the battery terminals. Be careful to keep corrosion from coming into contact with your eyes.
3.4 Add distilled water in each cell until the battery electrolyte reaches the level
specied by manufacturer. This helps purge excessive gas from cells. Do not overll. For a battery without caps, carefully follow the manufacturer’s
recharging instructions.
3.5 Study all battery manufacturer’s specic precautions, such as removing or
not removing cell caps while charging, and recommended rates of charge.
3.6 Determine voltage of the battery by referring to the vehicle owner’s manual, and make sure that the output voltage selector switch is set at the
correct voltage. If the charger has an adjustable charge rate, charge the
battery initially at lowest rate. If the charger has only one voltage, verify
that the battery voltage matches the voltage of charger. For a charger
3
not having an output voltage selector switch, determine the voltage of
(D)
(A)
(C)
(B)
the battery by referring to the vehicle owner’s manual and make sure it matches the output rating of the battery charger.
4. AC POWER CORD CONNECTION INSTRUCTIONS
4.1 The charger must be grounded to reduce the risk of electric shock. The charger is equipped with an electric cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER: NEVER ALTER CHARGER’S ORIGINAL AC CORD OR
PLUG. IF THE PLUG DOES NOT FIT OUTLET, HAVE PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN. IMPROPER CONNECTION CAN RESULT IN THE RISK OF AN ELECTRIC SHOCK. DISCONNECT THE PLUG FROM OUTLET WHEN CHARGER IS IDLE.
4.2 This battery charger is for use on a nominal 120-volt circuit and has a
grounding plug that looks like the plug illustrated in Figure A. A temporary adapter, which looks like the adapter illustrated in Figures B and C, may be used to connect this plug to a two-pole receptacle as shown in Figure B, if
a properly grounded outlet is not available. The temporary adapter should
be used only until properly grounded outlet can be installed by a qualied
electrician.
DANGER: BEFORE USING AN ADAPTER AS ILLUSTRATED, BE
CERTAIN THAT THE CENTER SCREW OF THE OUTLET PLATE IS GROUNDED (D). THE GREEN-COLORED RIGID EAR OR LUG EXTENDING FROM ADAPTER MUST BE CONNECTED TO A PROPERLY GROUNDED OUTLET. MAKE CERTAIN IT IS GROUNDED. IF NECESSARY, REPLACE THE ORIGINAL OUTLET COVER PLATE SCREW WITH A LONGER SCREW THAT WILL SECURE THE ADAPTER EAR OR LUG TO THE COVER PLATE AND MAKE THE GROUND CONNECTION TO THE GROUNDED OUTLET.
4
4.3 An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of re and electric shock. If an extension cord must be used, make sure:
a. That the pins on the plug of extension cord are the same number, size,
and shape as those of the plug on charger;
b. That the extension cord is properly wired and in good electrical
condition;
c. That the wire size is large enough for AC ampere rating of the charger
as specied in the following table.
Recommended minimum AWG size for extension cords
for battery chargers
AC Input rating, Amps AWG size of cord
Length of cord, feet (m)
Equal to or
greater than
But less than
25 50 100 150
(7.6) (15.2) (30.5) (45.6) 0 2 18 18 16 16 2 4 18 16 12 10 4 6 16 14 10 8 6 8 16 12 10 8 8 10 14 12 8 6
10 12 14 12 8 6 12 14 14 10 8 6
5. CHARGER LOCATION
5.1 Locate the charger as far away from the battery as the charger cables permit.
5.2 Never place the charger directly above the battery being charged; gases from the battery will corrode and damage charger.
5.3 Never allow the electrolyte to drip on the charger when taking gravity
readings or lling a battery.
5.4 Operate the charger only in well ventilated area, free of dangerous vapors.
5.5 Store the charger in a safe, dry location and maintain it in perfect condition.
5.6 Do not set the battery on top of charger or where acid might drip onto charger.
5
6. DC CONNECTION PRECAUTIONS
6.1 All switches should be set in OFF (O) position and the AC cord should be disconnected from the electrical outlet before you connect and disconnect the charger clamps. Never allow the clamps to touch each other.
6.2 Attach clamps to battery posts and twist or rock back and forth several times to make a good connection. This will tend to prevent the clamps from slipping off terminals, avoid dangerous sparking, and assure safer and
more efcient charging. Keep the clamps clean.
CAUTION: SETTING SWITCHES TO OFF (O) DOES NOT ALWAYS
DISCONNECT THE CHARGER ELECTRICAL CIRCUIT FROM THE AC POWER CORD OR DC CHARGER CLAMPS.
7. CHARGING BATTERY IN VEHICLE OR EQUIPMENT, OR CONNECTED TO ENGINE
7.1 Before working on the vehicle, rmly apply the emergency brake and place
the gearshift to NEUTRAL. Shift an automatic transmission to PARK.
7.2 Locate the charger as far away from the battery as the charger cords permit, and position the AC and DC cords to avoid stepping on or tripping over them and to prevent damage by hood, doors, or moving engine parts.
7.3 Stay clear of fan blades, belts, pulleys, and any other parts that can cause
physical injury.
7.4 Turn OFF all vehicle loads, including door lights, and correct any defects in
vehicle’s electrical system that may have caused low battery.
7.5 Check the polarity of battery posts. The POSITIVE (POS., P, +) post usually has larger diameter than NEGATIVE (NEG., N,–) post.
7.6 Determine which post of the battery is grounded (connected) to the chassis. If the negative post is grounded (as in most vehicles), see paragraph 7.7. If the positive post is grounded, see paragraph 7.8.
7.7 For a negative-grounded vehicle, rst connect the POSITIVE (red) clamp from the charger to the POSITIVE (POS., P, +) ungrounded post of battery. Then connect the NEGATIVE (BLACK) clamp to vehicle chassis or engine block away from battery. Do not connect the clamp to the carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy-gauge metal part of the frame or engine block. When disconnecting the charger, turn the switch to OFF (O), disconnect the AC cord, remove the clamp from the vehicle chassis, and then remove the clamp from the battery terminal.
7.8 For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clamp from the charger to the NEGATIVE (NEG., N, –) ungrounded post of the battery. Then connect the POSITIVE (RED) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy-gauge metal part of the frame or engine block.
6
When disconnecting the charger, turn the switch to OFF (O), disconnect
the AC cord, remove the clamp from the vehicle chassis, and then remove the clamp from the battery terminal.
CAUTION: WHEN THE POSITIVE (+) POST OF THE VEHICLE
BATTERY IS GROUNDED, DOUBLE-CHECK POLARITY.
8. CHARGING BATTERY OUTSIDE VEHICLE OR EQUIPMENT–NOT CONNECTED TO ENGINE
If necessary to remove the battery from the vehicle or equipment, always
remove the grounded terminal from the battery rst.
WARNING: MAKE SURE ALL VEHICLE LOADS ARE OFF TO PREVENT
A POSSIBLE ARC.
FOLLOW THESE STEPS WHEN THE BATTERY IS OUTSIDE THE
VEHICLE. A SPARK NEAR BATTERY MAY CAUSE AN EXPLOSION. TO REDUCE RISK:
8.1 Check the polarity of the battery posts. The POSITIVE (POS., P, +) post usually has a larger diameter than the NEGATIVE (NEG., N, –) post.
8.2 Attach an insulated battery cable that is at least a 24-inch, 6-gauge to the NEGATIVE (NEG., N, –) battery post.
8.3 Connect the POSITIVE (RED) charger clamp to the POSITIVE (POS., P, +) post of the battery.
8.4 Position yourself and the free end of cable as far away from the battery as
possible. Do not face the battery when making the nal connection. Then
connect the NEGATIVE (BLACK) charger clamp to the free end of the cable.
8.5 When disconnecting the charger, always do so in the reverse sequence of
the connecting procedure. Break the rst connection while staying as far
away from the battery as practical.
8.6. A marine (boat) battery must be removed and charged on shore. To charge it on board requires equipment specially designed for marine use.
7
9. ELECTRICAL CONDITION OF BATTERY
9.1 The state of charge of rellable-top batteries can be checked by using a
hydrometer. A hydrometer is a bulb-type syringe which is used to extract a small quantity of the electrolyte from each battery cell. Types are calibrated
in terms of specic gravity (a common scale being 1.120 to 1.265) or the type which uses four colored balls to indicate the state of charge. A oat in the hydrometer barrel indicates the specic gravity of the electrolyte. This specic gravity reading indicates the battery’s state of charge at a given
temperature, as shown in the table below:
State of Charge of
Battery at 80°F (27°C)
100% 1.280 1.265 1.225 4
75% 1.240 1.225 1.185 3 50% 1.200 1.190 1.150 2 25% 1.170 1.155 1.115 1
Discharged 1.140 1.120 1.080 *
**Initialspecicgravityreadingsvary,dependingonbatterytypeandmanufacturer.
Contactthesellerormanufacturerofthebatteryforthisspecication.
*Noballsoatinthebarrelofthehydrometer.
1.280 1.265 1.225 Floating Balls
** Initial Specic Gravity Reading
9.2 The state of charge of sealed-top (maintenance-free and recombination­type) batteries must be checked with a high resolution voltage tester.
9.3 If uncertain about type of battery you will be charging, or the correct procedure for checking the battery’s state of charge, contact the seller or manufacturer of the battery.
9.4 The temperature of the battery and the equipment the battery is used
with has a dramatic effect on battery efciency and system power requirements. For example, at 0°F (–18°C ), a battery is operating at 40% of its rated efciency, while the engine it is attempting to start requires over twice as much power as would be necessary at 80°F (27°C).
8
10. BATTERY CHARGING
10.1 This charger adjusts the charging time in order to charge the battery completely, efciently and safely. However, this section includes guidelines
that can be used to estimate charging times.
10.2 The amount of time required to fully charge a weak battery is dependant on a number of factors. In addition to the degree of discharge, these factors include the type and rated capacity, temperature, age of the battery, and
amperage rating of the charger. At 70°F (22°C) the average discharged
battery will be recharged as follows.
Battery Charging Chart - Time
Battery Size - Amp Hours (Ah) Reserve Capacity RC)
Motorcycle/ Garden Tractor
Small - (12-22 Ah) 2 hrs NR NR NR NR NR
2-4
amp
Time to Charge Battery - Shown in Hours (hrs)
Charging Rate - Amps
6-10 amp
15
amp
20
amp
40
amp
60
amp
Large - (22-35 Ah) 5
Automotive/Truck (Groups 24, 27, 31, etc.)
Small - (70-100 RC)
Medium - (100-130 RC)
Large - (130-160 RC)
Heavy Duty - (160-190 RC)
Charging Times are based on a 50% discharged battery - approx
hrs
7.5 hrs
hrs
hrs
hrs
9
12
15
3.1 hrs
3.75 hrs
4.5 hrs
6
hrs
7.5 hrs
2.3 hrs
2
hrs
2.4 hrs
3.2 hrs
4
hrs
1.75 hrs
1.5 hrs
1.8 hrs
2.4 hrs
3
hrs
0.875 hrs
0.75 hrs
0.9 hrs
1.2 hrs
1.5 hrs
0.6 hrs
0.5 hrs
0.6 hrs
0.8 hrs
hrs
12-12.2 volts.
NR = Not Recommended.
Charging times will vary with battery type and condition.
10.3 Battery State – If a battery has only been slightly discharged, it can be
charged in less than a few hours. The same battery could take up to 10 hours if very weak. The battery state can be estimated by using the built-in tester. The lower the reading the longer charging will take.
10.4. Battery rating – A higher rated battery will take longer to charge than
a lower rated battery under the same conditions. A battery is rated in ampere-hours (AH), reserve capacity (RC) and cold cranking amps (CCA). The lower the rating the quicker the battery will be charged.
1
9
10.5 CAUTION - Do not leave Manual chargers unattended.
10.6 CAUTION: If at any time the battery gets hot (above 125°F (52°C)) or acid
comes out of vent caps, STOP charging.
10.7 To maximize battery life - Let automatic chargers complete charging.
11. MULTIPLE BATTERY CHARGING
Batteries of the same voltage may be connected in parallel for
maintenance charging. Charge time increases in proportion to the number of batteries. Rate of charge decreases in the same proportion.
Example: Charging 2 batteries in parallel will take 2 times longer; each
battery receives 1/2 the amount of charge showing on the ammeter. Thus, if the ammeter shows a 30-amp charge, each battery will get a 15-amp charge (when batteries have the same rating, same state of charge, etc.).
12. CHARGER FEATURES AND CONTROLS
12.1 LED Indicators: The battery charger has three LED lights. They indicate
different functions.
RED LED - A steady glow indicates POWER ON. Red LED ashes if there
is a problem (i.e. battery isn't charged within 8 hours).
YELLOW LED - A steady glow indicates proper connection to the battery.
Flashing yellow indicates no connection or reverse connection.
GREEN LED - A steady glow indicates that Float-mode Monitoring is
keeping your battery maintained at full charge.
As a safety precaution, after 24-hours of charging, the charger
automatically switchs OFF.
10
12.2 CIRCUIT BREAKER
This battery charger is equipped with a self-resetting circuit breaker. This
device protects the charger from temporary overloads. In the event of an overload, the circuit breaker will trip open and after a short cooling off period will reset automatically. This process is known as cycling and can be recognized by an audible clicking sound.
NOTE: Clicking sound is normal. Wait until charger automatically resets
itself.
CAUTION: Persistent clicking (more than 30 minutes) may indicate
reverse connection or shorted battery cells. (See TROUBLESHOOTING.)
13. MAINTENANCE INSTRUCTIONS
The charger is designed and built with high quality materials requiring only
a minimum amount of care.
13.1 Clamps should be cleaned each time the charger is used to prevent
corrosion from battery uid.
13.2 Cords should be coiled when the charger is not being used to prevent damage.
13.3 Other servicing should be performed by qualied service personnel.
14. TROUBLESHOOTING
14.1 Red LED doesn't light:
a. Charger is not plugged in. Plug in. b. AC outlet is dead. Plug in a lamp or other appliance to check for
voltage.
14.2 Charger will not turn ON when properly connected to power:
a. Battery recently used in vehicle and is fully charged. Battery doesn't
need charging.
14.3 Charger will not turn OFF:
a. Battery has problem and will not take full charge. Have battery
checked.
b. Battery is connected to application that draws a small current (such
as a vehicle's dome light). Requires more time to charge; continue charging.
11
15. LIMITED WARRANTY
SCHUMACHER ELECTRIC CORPORATION, WARRANTS EXCLUSIVELY TO THE ORIGINAL PURCHASER THAT THIS CHARGER WILL BE REPAIRED OR REPLACED IF IT FAILS DURING ITS LIMITED WARRANTY PERIOD OF TWO YEARS FROM DATE OF RECEIPT DUE TO DEFECTS IN MATERIAL OR WORKMANSHIP. A DATED SALES RECEIPT OR PROOF OF PURCHASE IS REQUIRED FOR ALL CLAIMS.
This warranty does not cover failures arising out of improper use, abuse, maintenance or operation of the product. This warranty does not cover chargers that are opened or tampered with in any way.
Repair or replacement as provided under this warranty is the exclusive remedy of the consumer. Schumacher Electric shall not be liable for any incidental or consequential damages for breach of any express or implied warranty on this product. Except to the extent provided by applicable law,
any implied warranty of merchantability or tness for a particular purpose
on this product is limited in duration to the warranty period.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitation on how long as implied warranty lasts, so the above limitations or exclusions may not apply to
you. This limited warranty gives you specic legal rights, and you may also
have other rights, which vary from state to state.
CUSTOMER SERVICE
For customer service (Monday through Friday), call:
1-888-263-4906, 7 a.m. to 4:30 p.m. (Central Time)
Return all products for warranty to your local NAPA Auto Parts Store.
12
Loading...
+ 30 hidden pages