Scholtès FN56TXA User Manual
Operating Instructions
Contents
Installation, 16-17
IT
Italiano, 1 Français, 28
GB
English,15
FR
Positioning
Electrical connection
Technical data
OVEN
GB
ES
Espanol, 41
FN 56 XA
FN 56
FNG 56
FN 56 T XA
FN 56 T
PT
Portuges, 55
Description of the appliance, 18
Overall view
Control panel
Start-up and use, 19-24
Setting the clock
Setting the minute minder
Using the oven
Manual cooking modes
Automatic cooking modes
Programming cooking
Practical cooking advice
Assistance
Oven cooking advice table
Precautions and tips, 25
General safety
Disposal
Respecting and conserving the environment
Care and maintenance, 26-27
Switching the appliance off
Cleaning the appliance
Cleaning the oven door
Replacing the light bulb
Assembling the sliding rack kit
Automatic cleaning using the PYROLYTIC cycle
Installation
560 m
m
.
45 mm.
GB
! Please keep this instruction booklet in a safe place
for future reference. If the appliance is sold, given
away or moved, please make sure the booklet is
also passed on to the new owners so that they may
benefit from the advice contained within it.
! Please read this manual carefully: it contains
important information concerning the safe operation,
installation and maintenance of the appliance.
Positioning
! Do not let children play with the packaging
material; it should be disposed of in accordance
with local separated waste collection standards (see
Precautions and tips).
! The appliance must be installed by a qualified
professional in accordance with the instructions
provided. Incorrect installation may damage
property or cause harm to people or animals.
Built-in appliance
Use an appropriate cabinet to ensure that the
appliance operates properly:
the panels adjacent to the oven must be made of
heat-resistant material;
cabinets with a veneer exterior must be
assembled with glues which can withstand
temperatures of up to 100°C;
to install the oven under the counter (see diagram)
or in a kitchen unit, the cabinet must have the
following dimensions:
Ventilation
To ensure adequate ventilation is provided, the back
panel of the cabinet must be removed. It is
advisable to install the oven so that it rests on two
strips of wood, or on a completely flat surface with
an opening of at least 45 x 560 mm (see figures).
Centring and fixing
Position the 4 tabs on the side of the oven so that
they are aligned with the 4 holes on the outer frame.
Adjust the tabs in accordance with the thickness of
the cabinet side panel, as shown below:
20 mm thick: take off the
removable part of the tab (see
diagram);
18 mm thick: use the first
groove, which has already
been set in the factory (see
diagram);
.
in
. m
m
m
7
4
5
23 mm.
595 mm.
5 mm.
595 mm.
545 mm.
24 mm.
45 mm.
558 mm.
576 mm.
! The appliance must not come into contact with
electrical parts once it has been installed.
The indications for consumption given on the data
plate have been calculated for this type of
installation.
16
593 mm.
16 mm thick: use the second
groove (see diagram).
Secure the appliance to the cabinet by opening the
oven door and inserting 4 screws into the 4 holes on
the outer frame.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of
a tool.
Electrical connection
! Ovens equipped with a three-pole power supply
cable are designed to operate with alternating
current at the voltage and frequency indicated on
the data plate located on the appliance (see below).
Fitting the power supply cable
1. Open the terminal
board by inserting a
screwdriver into the
side tabs of the cover.
Use the screwdriver as
a lever by pushing it
down to open the cover
(see diagram).
2. Install the power
supply cable by
loosening the cable
clamp screw and the
three wire contact
screws L-NConnect the wires to
the corresponding
NL
terminals: the Blue wire
to the terminal marked
(N), the Brown wire to
the terminal marked (L) and the Yellow/Green wire to
the terminal marked
(see diagram).
3. Fix the cable in place by fastening the clamp
screw.
4. Close the cover of the terminal board.
Connecting the electricity supply cable to the
mains
Install a standardised plug corresponding to the
load indicated on the data plate (see table).
The appliance must be directly connected to the
mains using an omnipolar switch with a minimum
contact opening of 3 mm installed between the
appliance and the mains. The switch must be
suitable for the charge indicated and must comply
with current electrical regulations (the earthing wire
must not be interrupted by the switch). The supply
cable must be positioned so that it does not come
into contact with temperatures higher than 50°C at
any point.
! The installer must ensure that the correct electrical
connection has been performed and that it is fully
compliant with safety regulations.
.
Before connecting the appliance to the power
supply, make sure that:
the appliance is earthed and the plug is compliant
with the law;
the socket can withstand the maximum power of
the appliance, which is indicated on the data
plate (see below);
the voltage is in the range between the values
indicated on the data plate (see below);
the socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be
easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only (see Assistance).
! The manufacturer declines any liability should
these safety measures not be observed.
APPLIANCE SPECIFICATIONS
width 43.5 cm
Dimensions
Volume
Electrical
connections
ENERGY LABEL
This appliance conforms to the
height 32 cm
depth 41.5 cm
58 l
voltage: 220-240V ~ 50Hz /
maximum power absorbed
2800W
Directive 2002/40/EC on the
label of electric ovens.
Standard EN 50304
Energy consumption for Natural
convection – heating mode:
Conventional;
Declared energy consumption for
Forced convection Class –
heating mode:
Roast.
following European Economic
Community directives:
2006/95/EEC dated 12/12/06
(Low Voltage) and subsequent
amendments – 2004/108/EEC
dated 15/12/04 (Electromagnetic
Compatibility) and subsequent
amendments - 93/68/EEC dated
22/07/93 and subsequent
amendments.
2002/96/EEC and subsequent
amendments.
1275/2008 stand-by/off mode.
GB
17
Description of
the appliance
GB
Overall view
Control panel
Control panel
GRILL
DRIPPING PAN
TEMPERATURE and TIME
digits
Preheating
indicator
DOOR LOCK
indicator
GUIDES for the
sliding racks
position 5
position 4
position 3
position 2
position 1
DURATION
icon
END OF COOKING
icon
MINUTE MINDER
icon
CLOCK
icon
MODE
icons
SELECTOR
knob
SET TIME
button
THERMOSTAT/SET
TIME
knob
18
Loading...