Sceptre Technologies X9WG User Manual

X9WG-NagaV

X9WS-NagaV

User’s Manual

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including
interference that may cause undesired operation.

FCC WARNING

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interferences to radio communications.

However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution:

To comply with the limits for an FCC Class B computing device, always
use the shielded signal cord supplied with this unit.

i

The Federal Communications Commission warns that changes or
modifications of the unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.

CE mark for Class B ITE (Following European standard EN55022/1998; EN61000­3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11)

Radio Frequency Interference Statement

Warning:

This is a Class B product. In a domestic environment, this product may
cause radio interference in which case the user may be required to take
adequate measures.

Canadian Doc Notice

For Class B Computing Devices

This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.

“Le présent appareil numérique n’èmet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la class B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par
le ministère des Communications du Canada."

ii

TABLE OF CONTENTS

TABLE OF CONTENTS ..........................................................................................III

Your New LCD Monitor 1
Unpacking 1
Identifying Components 3
Adjusting the Tilting Angle 5
Connecting AC Power and Video Cable 6

Power Management System 6

How to install the detacheable stand 7

The LCD Monitor's Control Panel 8

Adjusting the Monitor’s Display 9

TFT LCD Monitor Specifications 14
Supported Timing 16
Troubleshooting 17

iii

The LCD Monitor

Your New LCD Monitor

Your LCD Monitor has been designed to be versatile, ergonomic and
user-friendly. The LCD Monitor is capable of displaying most
standards, from 640x400 VGA to 1440x900 WXGA+. The digital
controls located on the front panel allow the user to easily adjust the
Monitor’s display parameters, and the LCD Monitor’s small footprint
gives you more room in your workspace for other peripherals.
Lightweight and compact, the LCD Monitor is the perfect solution for
users on the go. You can use the LCD Monitor for everything from
making business presentations to playing computer games. The
Monitor also has a VESA wall-mount function for added convenience.

The architecture of the LCD Monitor incorporates an LCD panel that
produces a clear display with low radiation emission. And with its low
power consumption, the LCD Monitor helps you reduce your power bill.

Unpacking

Before unpacking your LCD Monitor, prepare a suitable workspace for
your LCD Monitor and computer. Look for a stable, level and clean
surface near a wall outlet. Even though the LCD Monitor uses very
little power, you should put it in a location which allows sufficient
airflow to ensure that the LCD Monitor and your computer do not
overheat. Set up your LCD Monitor so that the panel is not facing a
window where sunlight often comes in. The glare caused by sunlight
reflecting off of the LCD Monitor’s screen will make it difficult to use
the Monitor for viewing.

1 Rev.1

Note: Using a computer for an extended period of time with a poor workstation
set-up and incorrect working habits can cause health problems. The science of
ergonomics studies the relationship between health and a suitable working
environment. There is a section on ergonomics at the end of this chapter. For
more information on ergonomics, contact your nearest computer bookstore, or
local library. The Internet also has information on this and other subjects.

If you previously were using a CRT monitor instead of a LCD monitor,
please do not connect the LCD monitor to your computer yet. Please
use the CRT monitor and turn on your computer. Make sure your video
card’s refresh rate is at 60hz in the Display Setting’s Advance Menu
under the Display Adapter tab. Once that is achieved you can then turn
off the computer and plug your new LCD monitor in

After unpacking your LCD monitor, make sure the following items are included
in the box and are in good condition:

• LCD monitor

• Power Cord

• Monitor-To-PC Analog signal cable 15pin

• Monitor-To-PC DVI signal cable

• 1.5M stereo Jack Audio Cable

• User’s manual

If you find that any item to be missing or appear to be damaged,
contact your dealer immediately. Do not throw away the packing
material or shipping carton in case you need to ship or store the LCD
monitor in the future.

2 Rev.1

Identifying Components

A. The LCD Monitor — Front View

3

1

2

Figure 1-1: The LCD Monitor Front View

1. Power-On Indicator
This foursquare LED indicator blue lit when the power is on
and red lit when the LCD monitor is in power-saving mode.

2. Monitor Stand

3. LCD Screen

The LCD monitor screen is a 19-inch TFT 1440 x 900 Wide
WXGA+ screen.

4. LCD Monitor Control Panel

Refer to Chapter 2 for more details.

4

3 Rev.1

B. "Hot Keys" for Quick Adjustment of Monitor Settings

Figure 1-2: "Hot Keys"

1. Brightness adjustment "hot key":

Press - or + buttons to allow you to
adjust the brightness function

2. Source select “ Hot Key :

Press “ S “ button to allow you to
change the input source between DVI
port and RGB port, if the screen can’t
detect signal, then it will switch to the
next automatically

If DVI port connects to a PC , display
PC screen.

3. Auto adjustment “ Hot Key “

Press this to allow you to do the
auto adjustment to get the optimized
view

( For VGA port only, DVI port can’t

adjustment )

50

Source D-Sub

Source DVI

4 Rev.1

Adjusting the Tilting Angle

The LCD Monitor’s angle settings range from 0° to 10°.

10

0 to 10

Figure 1-3: Tilting the Monitor

5 Rev.1

Connecting AC Power and Video Cable

Note: Turn off your PC and the LCD monitor before connecting your LCD
monitor to the computer.

AC-IN

Audio

DVI

AC Outlet
(Wall Socket)

Computer Power Cord

Figure 1-4: The AC Adapter

VGA

Power Management System

This LCD Monitor complies with the VESA DPMS power management
proposal.

When the LCD Monitor is in power-saving mode or detects an incorrect
timing, the monitor screen will be blank and the power LED indicator from
blue lit change to red lit and the power LED indicator starts blinking.

6 Rev.1

How to install the detacheable stand:

Please see the below drawing.

7 Rev.1

The Display Controls

The LCD Monitor’s Control Panel

Figure 2-1: The Control Panel

1. Cursor Movement button Y &Z

These buttons let you move horizontally across your settings

2. Ajustment button - & +
These buttoms let you to change the setting value or move

to next sub-menu

3. Menu: OSD Menu button

Press this button to display the OSD (On-Screen Display)
menu.

4. Source: Source select hot key

Press this button to change the input source from D-Sub to
DVI

5. Power Switch

This button lets you turn power for the LCD monitor ON or
OFF.

8 Rev.1

Adjusting the Monitor’s Display

OSD Main Menu

1. Pressing the OSD Menu button causes the screen below to appear.

2. Use the Y &Z key to select the desired group, then press - & + key

to the sub-menu

3. Repeat step 2 to select the changed item, then press - & + to change the

value.

4. Press the Menu to return to the sub-menu item 3 to another adjustment

Timing : 1440 x 900

V/H Freq : 60Hz 55KHz

SCEPTRE X9WG-NagaV

Recommend 1440 x 900

The OSD Main Menu

OSD Main SCREEN

9 Rev.1

Auto Adjust Option

The Auto Adjust option lets the monitor determine and
select the settings that are most appropriate for your
system requirements.

Note: it only apply for Analog RGB input

Provides you with the current display timing information.

Brightness and Contrast Adjustment

Audio Function

Adjusts the Brightness value

Adjusts the Contrast value

Execute the white balance function

Return to the previous Menu

Volume : Adjust the speaker volume

Mute : Mute the speaker

Return

Color Temperature Adjustment

10 Rev.1

Set up the color temperature value

User Mode

Sets the color temperature to 6500K

Sets the color temperature to 9300K

Red change Red gain for the color temperature

(only valid when color temperature set at user mode )

Green change Green gain for the color temperature

(only valid when color temperature set at user mode )

Blue change Blue gain for the color temperature

(only valid when color temperature set at user mode )

Return to the previous Menu

Display Quality Adjustment

Auto Adjust: use this option to apply automatically setting

Changes the screen viewing size

11 Rev.1

Adjusts phase tracking to reduce display flicker

Moves the whole screen right or left

Moves the whole screen up or down

Return to the previous Menu

OSD Adjustment

Restores settings to factory default values

Sets the OSD timer

Moves the OSD menu horizontally

Moves the OSD menu vertically

Set the graphic mode or text mode

Return to the previous Menu

Exit the OSD screen

12 Rev.1

Note:

1) No video

When the monitor is ON and there is no video
signal received, the following message will be
displayed

2) Signal out of range

When the frequency range of the signal is out of the Monitor’s specifications,
(over 85HZ) the display will show the following message

Out of Range

13 Rev.1

Appendix A

TFT LCD Monitor Specifications

Item Specification

LCD Panel 19" WXGA+

Control
Functions
Power

On-Screen
Display
(OSD)

Main Menu Submenu
Information
Brightness

/Contrast Control

Audio Control Volume/Mute/Exit

Color temperature

Control

Software Power switch with LED indicator

(ON/OFF)

Brightness/Contrast/White
balance/Exit

User mode, 9300K, 6500K

R,G,B, gain value

Display Area
(mm)

Display
Colors

Video
Interface

Display Quality Auto Adjustment/Phase

adjustment/Screen Size/ Screen
Horizontal position/Screen Vertical
position/Exit

OSD adjsutment Restore to the default/OSD timer/OSD

Horizontal Position/OSD Vertical
Position/640&720/Exit

Exit

408.24 x 255.15
(19" diagonal)

16.7 M

VGA Compatible Analog RGB

Digital DVI interface

14 Rev.1

Item Specificaiton

Scanning Frequency
H/V, Hz

24-80K

50-75

Power Management Meets VESA DPMS

Power Consumption

40W/1W Max.

(ON/OFF, W)

Dimensions
WxHxD

Net Weight
(approx.)

18.72 x 16.14 x 6.89 in.
(475.4 x 410 x 175mm)

13.2 lbs
(6 Kg)

Power Supply Universal Input AC Socket

Environment Operating Temperature: 32 to 104°F (0 to 40° C)

Relative Humidity: 10% to 90%

Regulatory

FCC B DoC,UL/cUL,Energy star

15 Rev.1

Supported Timing

Appendix B

Item

1 NEC PC98 640x400 21.05 56.42 24.83
2 MAC 13" mode 640x480 30.24 66.67 35.00
3 MAC 16" mode 832x624 57.28 74.55 49.73
4 MAC 17" mode 1024x768 80.00 75.02 60.24
5 VGA 640x350 25.18 70.09 31.47
6 VGA 640x400 25.18 70.09 31.47
7 VGA 640x480 25.18 59.94 31.47
8 VESA 640x480 31.50 72.81 37.86

9 VESA 640x480 31.50 75.00 37.50
10 VESA 800x600 36.00 56.25 35.16
11 SVGA 800x600 40.00 60.32 37.88
12 VESA 800x600 50.00 72.19 48.08
13 VESA 800x600 49.50 75.00 46.88
14 VGA 720x400 28.32 70.09 31.47
15 XGA 1024x768 65.00 60.00 48.36
16 VESA 1024x768 75.00 70.07 56.48
17 VESA 1024x768 78.75 75.03 60.02
18 VESA 1152X864 108. 75.00 68.70
19 Non-VESA 1280x720 74.02 60 44.7
20 VESA 1280X1024 108 60 63.98
21 VESA 1280X1024 135 75 80

22 VESA 1440x900 106 60 55

Standards

Resolution

Dot Clock

(MHz)

Vertical

Scanning

Frequency

(Hz)

Horizontal

Scanning

Frequency

(kHz)

*Once a mode is optimized, there is no need to make any further adjustment
as long as the VGA card remains unchanged.

*Specifications are subject to change without notice.

16 Rev.1

Appendix C

Troubleshooting

This LCD monitor comes pre-adjusted with standard VGA timing. Due to
output timing differences among various VGA cards, you may initially
experience an unstable or unclear display when a new display mode or new
VGA card is selected.

Before applying any of the following troubleshooting procedures, you should
first apply the Auto Adjust option in the OSD menu.

PROBLEM: Display is unclear and unstable

To stabilize and clarify your display, open the OSD and adjust the clock and
phase to obtain a clear display

PROBLEM: There is no LCD display

If there is no display on the LCD, refer to the following:

1. Make sure that the power indicator on the LCD monitor is lit,
that all connections are secure, and that the system is running
on the correct timing. Refer to Appendix B for information on
timing.

2. Turn off the LCD monitor and then turn it back on again. Press
the OSD Menu button (refer to Chapter 2) once and then press
one of the Adjustment Control buttons several times. If there is
still no display, press the other Adjustment Control button
several times.

3. If step 2 does not work, connect your PC system to another
external CRT. If your PC system functions properly with a CRT
monitor but it does not function with the LCD monitor, and the
LCD monitor’s power LED is blinking, the output timing of the
PC’s VGA card may be out of the LCD’s synchronous range.

17 Rev.1

Change to one of the alternate modes listed in Appendix B, or
replace the VGA card and repeat steps 1 and 2.

4. If the power LED is not lit, check that the AC power connector is

securely connected, and verify that the AC adapter LED is lit. If
the AC adapter LED is not lit, please contact your dealer for
assistance.

PROBLEM: The LCD displays “signal out of range” error message

1. If you have a CRT monitor, please connect the CRT monitor to

the computer and change the refresh rate down to 60 Hz via
your video card’s display settings menu. After the setting of 60
Hz has been change you can then use the LCD on the
computer.

2.

If you do NOT have a CRT monitor, please make sure both the
X9WG-NagaV or X9WS-NagaV and your computer is turned off.
Afterwards turn on the LCD and the computer.

3.

While the computer is turned on, press the “F8” key on your
keyboard continuously until a selection menu appears and
select the “Safe Mode” option.

4.

When you’ve entered Safe Mode please uninstall any video
card driver and monitor driver by using either the “Add /
Remove Programs” icon or going into “System Properties” and
manually removing anything under “Monitors” and “Display
Adapters”.

5.

After removing all the drivers, please reboot your computer and
you should be able to see windows. Please then proceed to
install your monitor driver first, then your video card driver.
Please remember to make sure your refresh rate should be at
60 Hz.

18 Rev.1