Sceptre X270 User Manual

Important Information

SCEPTRE X270 Page1

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
This device may not cause harmful interference
This device must accept any interference received, including interference that my
cause undesired operation.

Please Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generate s uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructio ns,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Caution: To comply with the limits for an FCC Class B computing device,
always use the signal cord and power cord supplied with this

unit.

The Federal communications Commission warns that changes or modifications to
the unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

Page2 SCEPTRE X270

European Notice
CE mark for Class B ITE (Following European standard EN55022/1998;
EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998,
EN60950/1992+A1+A2+A3+A4+A11)

Radio Frequency Interference Statement

Warning:

This is a Class B product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.

Canadian Doc Notice

For Class B Computing Devices

This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.

“Le présent appareil numérique n’èmet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la class B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada."

SCEPTRE X270 Page3

Important Information

Electricity is used to perform many useful functions, but it can also cause personal injuries and
property damage if improperly handled. This product has been engineered and manufactured with
the highest priority on safety. However, improper use can result in electric shock and / or fire. In
order to prevent potential danger, please observe the following instructions when installing, operating
and cleaning the product. To ensure your safety and prolong the service life of your Liquid Crystal
Display, please read the following precautions carefully before using the product.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade and the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at the plugs,
convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

13. Unplug this apparatus during lightening storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.

Page4 SCEPTRE X270

Tips and Safety Precautions

This product is designed and manufactured to operate within defined design limits, and misuse may
result in electric shock or fire. To prevent the product from being damaged, the following rules should
be observed for the installation, use and maintenance of the product. Read the following safety
instructions before operating the display. Keep these instructions in a safe place for future reference.

• To avoid the risk of electric shock or
component damage, switch off the power
before connecting other components to the
X270 LCD MONITOR.

• Unplug the power cord before cleaning the
X270 LCD MONITOR. Do not use a liquid
or a spray cleaner for cleaning the product.
Do not use abrasive cleaners.

• Always use the accessories recommended
by the manufacturer to insure compatibility.

• When moving the X270 LCD MONITOR
from an area of low temperature to an area
of high temperature, condensation may
form on the housing. Do not turn on the
X270 LCD MONITOR immediately after
this to avoid causing fire, electric shock or
component damage.

• Do not place the X270 LCD MONITOR on
an unstable cart, stand, or table. If the
X270 LCD MONITOR falls, it can injure a
person and cause serious damage to the
appliance. Use only a cart or stand
recommended by the manufacturer or sold
with the X270 LCD MONITOR.

• Any heat source should maintain a
distance of at least 5 feet away from the
X270 LCD MONITOR, i.e. radiator, heater,
oven, amplifier etc. Do not install the
product too close to anything that
produces smoke or moisture. Operating
the product close to smoke or moisture
may cause fire or electric shock.

• Slots and openings in the back and bottom
of the bezel are provided for ventilation. To
ensure reliable operation of the X270 LCD
MONITOR and to protect it from
overheating, be sure these openings are

not blocked or covered. Do not place the
X270 LCD MONITOR in a bookcase or
cabinet unless proper ventilation is
provided.

• It is not recommended to use the X270
LCD MONITOR in a portrait format (by
rotating 90 degrees) under high
temperature environment (25°C or higher),
since this would retard heat dissipation
and would eventually damage the monitor.

• Never push any object into the ventilation
slots of the X270 LCD MONITOR. Do not
place any objects on the top of the Product.
It could short circuit parts causing a fire or
electric shock. Never spill liquids on the
X270 LCD MONITOR.

• The X270 LCD MONITOR should be
operated only from the type of power
source indicated on the label. If you are not
sure of the type of power supplied to your
home, consult your dealer or local power
company.

• The power cable must be replaced when
using different voltage from that specified
in the User Manual. For more information,
contact your dealer.

• The X270 LCD MONITOR is equipped with
a three-pronged grounded plug, a plug
with a third (grounding) pin. This plug will
fit only into a grounded power outlet as a
safety feature. If your outlet does not
accommodate the three-wire plug, have an
electrician install the correct outlet, or use
an adapter to ground the appliance safely.
Do not defeat the safety purpose of the
grounded plug.

SCEPTRE X270 Page5

• Do not overload power strips and
extension cords. Overloading can result in
fire or electric shock.

• The wall socket should be installed near
the equipment and should be easily
accessible.

• Only the marked power source can be
used for the product. Any power source
other than the specified one may cause
fire or electric shock.

• Do not touch the power cord during
thunderstorms. To avoid electric shock,
avoid handling the power cord during
electrical storms.

• Unplug the unit during a lightning storm or
when it will not be used for a long period of
time. This will protect the X270 LCD
MONITOR from damage due to power
surges.

• Do not attempt to repair or service the
product yourself. Opening or removing the
back cover may expose you to high
voltages, the risk of electric shock, and
other hazards. If repair is required, please
contact your dealer and refer all servicing
to qualified service personnel.

• Keep the product away from moisture. Do
not expose this appliance to rain or
moisture. If water penetrates into the
product, unplug the power cord and
contact your dealer. Continuous use in this
case may result in fire or electric shock.

• Do not use the product if any abnormality
occurs. If any smoke or odor becomes
apparent, unplug the power cord and
contact your dealer immediately. Do not try
to repair the product yourself.

• Avoid using dropped or damaged
appliances. If the product is dropped

and the housing is damaged, the internal
components may function abnormally.
Unplug the power cord immediately and
contact your dealer for repair. Continued
use of the product may cause fire or
electric shock.

• Do not install the product in an area with
heavy dust or high humidity. Operating the
product in environments with heavy dust or
high humidity may cause fire or electric
shock.

• Hold the power connector when removing
the power cable. Pulling the power cable
itself may damage the wires inside the
cable and cause fire or electric shocks.
When the product will not be used for an
extended period of time, unplug the power
connector.

• T o avoid risk of electric shock, do not touch
the connector with wet hands.

• Insert batteries in accordance with
instructions while using the remote control.
Incorrect polarities may cause damage
and leakage of the batteries, operator
injury and contamination the remote
control.

• If any of the following occurs please
contact the dealer:

o The power connector fails or

frays.

o Liquid sprays or any object

drops into the X270 LCD
MONITOR.

o The Display is exposed to rain or

other moisture.

o The Display is dropped or

damaged in any way.

o The performance of the Display

changes substantially.

• Operating environment: Temperature: 5°C
~ 35°C, Humidity: 10% to 90%
non-condensing, Altitude: 0~10,000 ft.

Page6 SCEPTRE X270

Table of Contents

Important Information ............................................................................................................................. 1

FCC Compliance Statement ................................................................................................................... 2

Important Information ............................................................................................................................. 4

Tips and Safety Precautions .................................................................................................................. 5

Table of Contents ................................................................................................................................... 7

Opening the Package ............................................................................................................................. 9

Package Contents .................................................................................................................................. 9

Installing or Uninstalling the Base .......................................................................................................... 9

Setting Up Your Monitor ....................................................................................................................... 10

Mounting Preparations ......................................................................................................................... 11

Identifying Front and Rear Panel ......................................................................................................... 12

Front View ................................................................................................................................. 12

Rear View Connections ............................................................................................................. 12

Control Buttons .......................................................................................................................... 13

Understanding Your Cables & Connections .............................................................................. 13

Connecting the LCD ............................................................................................................................. 14

If You Have DVI Connection on Your Video Card… .................................................................. 14

If You Have VGA Connection on Your Video Card… ................................................................. 15

If You Have HDM I Connection on Your Cable or Satellite Box… .............................................. 16

On Screen Display (OSD) Menu .......................................................................................................... 17

AUTO IMAGE ADJUST ............................................................................................................. 17

CONTRAST / BRIGHTNESS .................................................................................................... 18

INPUT SELECT ......................................................................................................................... 19

AUDIO ADJUST ........................................................................................................................ 19

COLOR ADJUST .................................................................................................................. ..... 20

INFORMATION .......................................................................................................................... 20

MANUAL IMAGE ADJUST ........................................................................................................ 21

SETUP MENU ........................................................................................................................... 22

MEMORY RECALL ................................................................................................................... 22

Supported PC Resolution ..................................................................................................................... 23

Supported Video Resolution ................................................................................................................ 23

Troubleshooting .................................................................................................................................... 24

How do I clean the LCD? ..................................................................................................................... 27

Specification ......................................................................................................................................... 28

Call Us If You Need Help! ..................................................................................................................... 29

LIMITED PRODUCT WARRANTY ....................................................................................................... 30

Disclaimer & Copyright Information ...................................................................................................... 32

SCEPTRE X270 Page7

Dear SCEPTRE Customer,

Congratulations on your new SCEPTRE monitor purchase. Thank you for your support. To ensure
safety and many years of trouble free operation of your LCD monitor, please read the manual carefully
before making any adjustments, and keep them in a safe place for future reference. We hope you
enjoy your new SCEPTRE monitor.

For technical assistance, please call 1800-788-2878 and select option 3 or email our tech support
group at [e-mail].

For all other inquiries, please call 1800-788-2878 and select option 4 or email our customer service
group at [e-mail].

We recommend you register your SCEPTRE monitor with the enclosed registration card and mail it in.
For peace of mind and to protect your investment beyond the standard warranty, SCEPTRE offers a
two year extended warranty service for your LCD monitor. This plan gives additional coverage once
your standard warranty period runs out. Please call our customer service group to purchase the
extended warranty.

Page8 SCEPTRE X270

Opening the Package

The SCEPTRE X270 is packaged in a carton together with standard accessories. The weight of the LCD display is
approximately 14.1 lbs. Since the LCD panel can be easily scratched or broken, please handle the product gently.
Never place the unit on a surface with the glass facing downw ards unless it is on a protectiv e padding. When opening
the carton, make sure the product is in good condition and that all the standard accessories and items are included.
After unpacking your LCD monitor, be sure to save the original box and all packing materials for future shipping
needs.

Package Contents

z Monitor Display x 1
z User Manual x 1
z Warranty Card x 1
z Power Cord x 1
z DVI Cable x 1
z 3.5 mm Mini-jack Audio Cable x 1

Installing or Uninstalling the Base

1. Please place the base on a flat surface (i.e. table). Hold the monitor directly 90 degrees above the base.

Connect the monitor to the base by inserting the monitor into the base. To remove the base simply look at the
bottom of the base and unlock the two buckles at the bottom of the base.

SCEPTRE X270 Page9

Setting Up Your Monitor

The following are general short steps to setup and use the monitor with your PC under the Microsoft
Windows XP operating system.

1. After you have installed the base, connect your VGA or DVI cord to both the monitor and PC and

turn on the PC and the monitor.

2. While booting up keep pressing F8 and choose the VGA mode option.

3. Under Windows, use your mouse to right click on the background with nothing selected. Left click

on the PROPERTIES option. Click on the SETTINGS tab.

4. Under SETTINGS change your resolution to 1920x1080 and click on APPLY. (if you are using

DVI as your connection click on OK and you are done, steps 6-9 are unnecessary)

5. Click on ADVANCED button, and then click on MONITOR tab. Under MONITOR make sure your

refresh rate is set to 60 Hz.

6. Click on OK on all windows to exit.

7. On the monitor, press the [1] button then press the [2] button to AUTO ADJUST.

8. Wait until the monitor finishes calibrating. Reboot your computer and your monitor is ready for

use.

9. [OPTIONAL] Because this monitor’s native resolution is very high, words may seem too small for

some users. Please follow steps 1-5. Afterwards, click on the GENERAL tab. In there you
can change the size of the words by changing from the option from “normal size” to “large size”.
Click on APPLY to finalize this selection. This will make the words bigger under Windows XP.

The following are general short steps to setup and use the monitor with your PC under the Microsoft
Windows VISTA and Windows 7 operating system.

1. After you have installed the base, connect your VGA or DVI cord to both the monitor and PC and

turn on the PC and the monitor.

2. While booting up keep pressing F8 and choose the VGA mode option.

3. Under Windows, use your mouse to right click on the background with nothing selected. Left click

on the PERSONALIZE option. Click on the DISPLAY SETTINGS option.

4. Change your resolution to 1920x1080 and click on APPLY. (if you are using DVI as your

connection click on OK and you are done, steps 6-9 are unnecessary)

5. Click on ADVANCED SETTINGS button, and then click on MONITOR tab. Under MONITOR

make sure your refresh rate is set to 60 Hz.

6. Click on OK on all windows to exit.

7. On the monitor, press the [1] button then press the [2] button to AUTO ADJUST.

8. Wait until the monitor finishes calibrating. Reboot your computer and your monitor is ready for

use.

9. [OPTIONAL] Because this monitor’s native resolution is very high, words may seem too small for

some users. Under Windows Vista please right click on the background with nothing selected
and select the PERSONALIZE option. Afterwards, click on the ADJUST FONT SIZE (DPI)
option on the left column and click on continue. In there you can change the size of the words by
changing from the option from “default scale” to “large scale”. This will make the words bigger
under Windows VISTA. Click on APPLY to finalize your selection.

Page10 SCEPTRE X270

Mounting Preparations

1. Place the monitor on a flat surface with cloth so the bezel does not get scratched. Unscrew the

4 screws that lock the arm to the monitor. Once the 4 screws are removed, the stand will come
off.

2. The monitor is ready for mounting.

Please note : The mounting pattern of the monitor is 100mm x 100mm using M4 metric system screws.

The screw depth of the mounting pattern should not exceed 8mm. The 4 screws removed are for

securing the monitor stand only. If you are mounting the monitor please consult a qualified installer

for further instructions on bracket support and wall support.

SCEPTRE X270 Page11

Identifying Front and Rear Panel

Front View

POWER INDICATOR : If light is blue, the monitor is turned on. If the light is blinking blue, the monitor

is turned on but not receiving a signal from the computer.
NATIVE RESOLUTION : This monitor’s clearest picture is produced under its native resolution. The
native resolution of the monitor is 1920x1080 at 60 Hz refresh rate.

Rear View Connections

POWER – This plug is responsible for providing power to the monitor.
AUDIO IN – This connection is for audio out from the PC to connect to the monitor.
HDMI – HDMI stands for High Definition Multimedia Interface. This connection is for AV devices such

as blu-ray dvd player or game consoles such as Playstation®3.
DVI – DVI stands for Digital Video Interface. This connection is for computers to send video signals to
the monitor digitally so that colors and video are more accurate and vivid.
VGA – VGA stands for Video Graphics Array. This connection is for computers to send video signals to
the monitor by an analog signal. This method of connection is the most commonly used connection.

Page12 SCEPTRE X270

Control Buttons

1. [1] – This button turns the On Screen Display (OSD) on or off.

2. ▼ – While in the OSD this button acts as a navigation button moving your selection to the next

one. If you entered the function this button acts as the decrease adjustment button. This button
also acts as the hotkey for adjusting DCR, contrast, brightness, and ECO Mode.

3. ▲ – While in the OSD this button acts as a navigation button moving your selection to the

previous one. If you entered the function this button acts as the increase adjustment button.
This button also acts as the hotkey for selection preset color modes under Opticolor Mode.

4. [2] – This button confirms your selection. i.e. If you want to adjust brightness, you would highlight

brightness and press [2] to begin adjusting brightness. This button acts as hotkey for source.

5. – This button turns the monitor ON or OFF.

Understanding Your Cables & Connections

Cable
Name

DVI

(digital video)

VGA

(analog

video)

3.5 mm

Mini-jack

HDMI

Cable Picture

Corresponding Connection

Picture

*The cables above do not represent the package’s actual content.

SCEPTRE X270 Page13

Connecting the LCD

If You Have DVI Connection on Your Video Card…

1. Make sure the power of X270 LCD MONITOR is turned off.

2. Obtain a DVI cable and connect to the DVI connection on your PC. Connect the other
end of the cable to your X270 LCD MONITOR.

3. Turn on the power of both the X270 LCD MONITOR and the PC.

Please Note :

• Some video cards may have their DVI connection turned off by default. If you do

not get video, please consult your video card’s technical support.

• The PC’s clearest picture is produced under 1920x1080 at 60Hz.

Page14 SCEPTRE X270

If You Have VGA Connection on Your Video Card…

1. Make sure the power of X270 LCD MONITOR is turned off.

2. If you were previously using a CRT (bulky) monitor, please hook up your old
monitor first and make sure your refresh rate is set to 60 Hz frequency before using the
X270 LCD MONITOR. You can find the refresh rate information and change it by
RIGHT CLICKING on the desktop with nothing selected. After you have right clicked,
select the PROPERTIES option. Click on the SETTINGS tab. Click on the ADVANCED
button. Click on the MONITOR tab. In that tab, change the refresh rate to 60Hz and
click on APPLY. After the refresh rate changed, please shut down the computer and
monitor.

3. Obtain the VGA cable and connect to the VGA connection on your PC. Connect the
other end of the cable to your X270 LCD MONITOR.

4. Turn on the power of both the X270 LCD MONITOR and the PC.

Please Note :

• The PC’s clearest picture is ran with 1920x1080 at 60Hz.

SCEPTRE X270 Page15

If You Have HDMI Connection on Your Cable or Satellite Box…

1. Make sure the power of the X270 LCD MONITOR is turned off.

2. Obtain a HDMI cable and connect one end to the back of the monitor and the other end

to the back of the cable or satellite box.

3. Turn on the power of both the X270 LCD MONITOR and the cable or satellite box.

Please Note :

• Make sure to set audio output from your cable or satellite box to PCM output.

• Please refer to the cable or satellite company for more information.

Page16 SCEPTRE X270

On Screen Display (OSD) Menu

The OSD menu of the monitor provides various adjustments for the monitor such as color, brightness,
contrast, screen settings…..etc.

When you press the [1] button on the monitor, the OSD screen will appear. Select each of the
functions with the ▲ or ▼ buttons. Use the [2] button to enter each of the function or when you’re in
the function already, use the [2] button to select the option you want to adjust. Use the ▲ or ▼ buttons
to adjust each option’s values.

AUTO IMAGE ADJUST

This function auto adjusts the clock and phase of the monitor when using VGA cable so the monitor
will sync better with the video card and produce a clearer picture.

1. To use this function, press the [1] button then press the [2] button.

Please Note:

• This function is only available under VGA connection.

SCEPTRE X270 Page17

CONTRAST / BRIGHTNESS

This function adjusts the brightness and contrast of the LCD.

1. To use this function, press [1] to open the OSD then highlight CONTRAST / BRIGHTNESS
function by pressing the ▲ or ▼ button.

2. Press [2] to enter the function.

3. Press ▲ or ▼ button to select BRIGHTNESS or CONTRAST to adjust.

4. Press [2] to select the option you want to adjust.

5. Use the ▲ or ▼ button to adjust the values.

Please Note :

• BRIGHTNESS adjusts the black level in a picture. If the value is adjusted too high,
the picture will look washed out. If too low, the picture will not have much detail in
dark colors.

• CONTRAST adjusts the white levels in a picture. If the value is adjusted too high,
the picture will not have any details in bright parts of the picture. If set too low,
the picture will looked washed out.

• DCR is a function that automatically adjusts the contrast for you depending
on the graphics displayed at the time.

• ECO Mode is a function that conserves power for the monitor.

Page18 SCEPTRE X270

INPUT SELECT

This function selects the source of the monitor.

1. Press [1] to open the OSD then highlight INPUT SELECT by pressing the ▲ or ▼ buttons.

2. Press [2] to enter the function.

3. Press the ▲ or ▼ buttons to select the source you want to change to.
Please Note:

• AUTO is a feature that automatically selects the source that has a video signal.

AUDIO ADJUST

This function changes the volume of the monitor’s speakers.

1. Press [1] to open the OSD then highlight AUDIO ADJUST by pressing the ▲ or ▼ buttons.

2. Press [2] to enter the function.

3. Press the ▲ or ▼ buttons to select the option you want to change to.

4. Press [2] to begin adjusting and use the ▲ or ▼ buttons to adjust.

SCEPTRE X270 Page19

COLOR ADJUST

This function adjusts the overall balance of white colors in a picture in large increments. Color
temperature consists of 5400K, 6500K, 9300K, and USER COLOR.

1. Press [1] to open the OSD then highlight COLOR ADJUST by pressing the ▲ or ▼buttons.

2. Press [2] to enter the function.

3. Press ▲ or ▼ button to select the option you want to adjust to. Use [2] to select the option.
a. 9300K – This option adjusts the white balance towards the blue color giving the

picture a bluish tint and cooler look.

b. 6500K – This option adjusts the white balance to give the picture a no biased

white color.

c. 5400K – This option adjusts the white balance towards the red color giving the

picture a reddish tint and warmer look.

d. USER COLOR – This option lets the user adjust the white balance by tweaking

the RED, GREEN, and BLUE color.

INFORMATION

This function gives you signal information sent to the monitor.

1. Press [1] to open the OSD then highlight INFORMATION by pressing the ▲ or ▼ buttons.

2. Press [2] to enter the function to look at your signal information.

Page20 SCEPTRE X270

MANUAL IMAGE ADJUST

This function adjusts the image of the monitor.

1. Press [1] to open the OSD then highlight MANUAL IMAGE ADJUST by pressing the ▲ or ▼

buttons.

2. Press [2] to enter the function.

3. Press the ▲ or ▼ buttons to select the option you want to adjust and press [2] to enter the

option.

4. Use the ▲ or ▼ buttons to adjust the values.
a. HORIZONTAL SIZE – This option expands or contracts the image horizontally.
b. H./V. POSITION – This option moves the image left, right, up, or down.
c. FINE TUNE – This option adjusts the picture clarity by adjusting data / clock of

your signal.
d. SHARPNESS – This option adjusts the sharpness of the signal.
e. VIDEO MODE ADJUST – This option adjusts the various scaling of video.

i. FULL SCREEN – This mode stretches anything to full screen.

ii. OVER SCREEN – This mode is for watching TV where it will perform

overscan for most TV videos.

iii. ASPECT RATIO – This mode maintains the aspect ratio of the

resolution. This function is unavailable for switching between 16:9 and
16:10 signals.

f. OPTICOLOR MODE – This option lets you select various preset color modes.

i. STANDARD – This mode is for general use.

ii. GAME – This mode is for playing games.
iii. CINEMA – This mode is for watching movies.
iv. SCENERY – This mode is for looking at pictures.

v. TEXT – This mode is for reading or writing text.

Please Note:

• Always use auto adjust first to adjust the image.

SCEPTRE X270 Page21

SETUP MENU

This function allows you to change the language of the OSD and adjust the OSD options.

1. Press [1] to open the OSD then highlight SETUP MENU by pressing the ▲ or ▼ buttons.

2. Press [2] to enter the function.

3. Press the ▲ or ▼ buttons to select the option you want to change to and press [2] to begin
adjusting the option

a. LANGUAGE SELECT – This option selects various languages for the OSD.
b. OSD POSITION – This option changes the position of the OSD.
c. OSD TIME OUT – This option changes how long the OSD menu will stay up.

Please Note :

d. OSD BACKGROUND OFF – This option adds or removes the OSD background.

• Changing the language of the OSD will alter all the messages and OSD language of the

monitor. There is no reset for this function.

MEMORY RECALL

This function recalls adjustments to the monitor.

1. Press [1] to open the OSD then highlight MEMORY RECALL by pressing the ▲ or ▼
buttons.

2. Press [2] to enter the function.

Page22 SCEPTRE X270

Supported PC Resolution

STD RESOLUTION & REFRESH RATE

VGA 720 x 400 @ 70Hz

VESA 640 x 480 @ 60Hz

MAC 640 x 480 @ 67Hz
VESA 640 x 480 @ 75Hz
VESA 800 x 600 @ 60Hz
VESA 800 x 600 @ 72Hz
VESA 832 x 624 @ 75Hz
VESA 800 x 600 @ 75Hz
VESA 1024 x 768 @ 60Hz
VESA 1024 x 768 @ 70Hz
VESA 1024 x 768 @ 75Hz
VESA 1280 x 960 @ 60Hz
VESA 1280 x 1024 @ 60Hz
VESA 1280 x 1024 @ 75Hz
VESA 1440 x 900 @ 60Hz
VESA 1440 x 900 @ 75Hz
VESA 1600 x 1200 @ 60Hz
VESA 1680 x 1050 @ 60Hz
VESA 1920 x 1080 @ 60Hz

Supported Video Resolution

VIDEO RESOLUTION

480p

720p

1080i

*Once a mode is optimized, there is no need to make any further adjustment as long as the VGA card

remains unchanged. **Specifications are subject to change without notice.

SCEPTRE X270 Page23

1080p

Troubleshooting

Problem Possible solutions

DISPLAY IS UNCLEAR
AND UNSTABLE

THERE IS NO LCD
DISPLAY or SCREEN
SAYS NO VIDEO

MONITOR SAYS
“SIGNAL OUT OF
RANGE”

To stabilize and clarify your display, use the AUT O ADJUST function or
change the resolution to the display’s optimal setting 1920 X 1080 at
60Hz, then AUTO ADJUST.
Make sure you switched to the correct source. Check both sources to
see video is on the other source. Check your video cable. It might be
corrupt. Swap out the video cable for another one to see if the monitor
will work. Check your power plug. See if it is fully plugged in on both
the monitor and the wall.
If you have a CRT monitor, please connect the CRT monitor to the
computer and change the refresh rate down to 60Hz via your video
card’s display settings menu. After the setting of 60Hz has been
change you can then use the LCD on the computer.

1. To change the setting go to display settings by right clicking
on your desktop with nothing selected. Choose the
PROPERTIES option.

2. Click on the SETTINGS tab, verify the resolution is NOT
higher than 1920x1080, and click on the ADVANCED
button.

3. Click on the MONITOR tab and change the refresh rate to
60Hz.

4. Click on OK 2-3 times to finalize your change.

If you do NOT have a CRT monitor or it’s already broken, please make
sure both the X270 monitor and your computer is turned off.

1. Turn on the LCD and the computer.

2. While the computer is turned on, press the “F8” key on your
keyboard continuously until a selection menu appears and
select the “Safe Mode” option.

3. When you’ve entered Safe Mode please uninstall any video
card driver and monitor driver by using either the “Add /
Remove Programs” icon or going into “System

4. Properties” and manually removing anything under
“Monitors” and “Display Adapters”. After removing all the
drivers, please reboot your computer and you should be
able to see windows. Please install your monitor driver
first, then your video card driver. Please remember to
make sure your refresh rate should be at 60Hz.

Page24 SCEPTRE X270

Problem Possible solutions

I CANNOT GET THE
RESOLUTION
1920x1080

If you are using DVI, please try out VGA to see if you are able to
achieve that resolution. If your VGA can then, your video card’s DVI
cannot support widescreen resolutions.

Sometimes your video card will not read the monitor correctly and will
not allow you to achieve the resolution you want. Rebooting your
computer will solve the situation.

Y ou can also make sure your video card’s video drivers are up to date.
You can find what video card you have by clicking on START then
RUN. Type in “DXDIAG”. When the diagnostic window pops up, click
on the DISPLAY tab. The program will tell you what video chipset you
have. Copy that name then search it with an online search engine like
GOOGLE™. Find your video card company’s web address and search
for newer drivers. If updating your drivers does not work, you probably
have one of the older video cards and cannot achieve a widescreen
resolution. You’ll need to upgrade your video card to a newer one.

I DO NOT HEAR ANY
SOUND FROM THE
SPEAKERS

THE VIDEO IS TOO
BRIGHT NO MATTER
WHAT I ADJUST

THE WORDS AND
VIDEO ARE TOO
BLURRY

THE COLORS ARE
NOT CORRECT

Check your 3.5 mm mini-jack cable and see if it is connected correctly
between the computer and the monitor. Check the volume of your
computer and also the volume of the monitor.
Sometimes having older video cards this type of problem might
happen due to newer LCDs having to provide HD video capability and
not being fully compatible with older video cards. You can try
adjusting the contrast to a lower value and adjust the brightness to
compensate.
Are you using the monitor’s native resolution? If not you’ll need to
switch resolution to the native 1920x1080 at 60 Hz to make the words
clearer. If you’re using VGA please do not forget to AUTO ADJUST.

If the words are still blurry, please try enabling or disabling CLEAR
TYPE function from windows.
Sometimes the colors are not correct because your VGA or DVI cable
is loose or corrupt. Please try reconnecting your cable or swap out
your current cable to see if the problem persists.

SCEPTRE X270 Page25

Problem Possible solutions

THE WORDS ARE TOO
SMALL A T 1920X1080

I DO NOT HEAR ANY
SOUND FROM THE
SPEAKERS WHEN
USING THE
(OPTIONAL) HDMI
PORT
MY X270 DOES NOT
HAVE THE HDMI PORT

At the native resolution of 1920x1080, some people might feel that the
words are too small to read. You can change the size of the words in
Windows Operating System via its display properties.

For Windows XP

1. Right click on the background with nothing selected. Left
click on the PROPERTIES option.

2. Click on the SETTINGS tab.

3. Under SETTINGS, click on the ADVANCED button.

4. Under GENERAL tab, change the size of the words by
selecting the option NORMAL SIZE and change it to LARGE
SIZE.

5. Click on OK on all windows to exit.

6. Once you have finished rebooting, the computer is ready for
use.

For Windows VISTA or Windows 7

1. Right click on the background with nothing selected. Left
click on the PERSONALIZE option.

2. Click on ADJUST FONT SIZE (DPI) option on the left
column and

3. Click on CONTINUE.

4. In there you can change the size of the words by changing
from the option DEFAULT SCALE to LARGE SCALE.

5. Click on APPLY to finalize your selection.

6. Once you have finished rebooting, the computer is ready for
use.

The monitor only decodes PCM sound signals. Make sure your
video device’s audio output is through HDMI and is outputting PCM
sound format.

The HDMI port is an optional design that is only available in certain
models.

Page26 SCEPTRE X270

How do I clean the LCD?

IMPORTANT

1. The power cable has to be removed from the socket before cleaning
the TV.

2. Do not use volatile solvent (alcohol, rosin, and toluene) to clean the
TV. These types of chemicals might damage the housing and the
LCD glass.

Cleaning the bezel

1. Use a 100% cotton cloth or micro-fiber cloth for cleaning.

2. If the bezel is dirty to the point where you cannot simply dry wipe it,
please lightly dampen the wiping material with clean water and wipe
again. Wipe the display with a dry micro-fiber cloth or 100% cotton
cloth afterwards.

Please Note :

• Make sure you wring the water out of the cloth before
cleaning the bezel in order to prevent water from
penetrating into the electronics.

Cleaning the Screen

1. Use a 100% cotton cloth or micro-fiber cloth for cleaning.

2. The LCD screen glass is extremely fragile. Do not scrape it with any
material. Do not press or tap the screen to avoid cracking. When
the screen is dirty to the point where you cannot simply dry wipe it,
please lightly dampen the wiping material with clean water and wipe
again. Wipe the display with a dry micro-fiber cloth or 100% cotton
cloth afterwards.

SCEPTRE X270 Page27

Specification

Display panel

Item

diagonal 27 inches

Active Area / Screen Size

597.6mm x 336.15mm
Aspect Ratio Widescreen 16 : 9
Pixel Pitch 0.31 (h) x 0.31 (v) mm
Resolution Native: 1920x1080
Brightness 400 nits
Contrast 1000:1 (NATIVE) 60,000:1 (DCR)
Response Time 5ms (Gray to Gray) ( OD 2ms )

Typical 170/160 Degree

Viewing Angle

(Horizontal/Vertical)

Lamp Life of Backlight > 50,000hrs

Monitor Display

25.5(W)X17.9(H)X9.43(D) inches
Dimension

646.9(W)X445.0(H)X239.5(D) mm
Weight 14.1 lbs (6.4 kg)

Illustration

Power input 100V to 240V AC @ 50/60 Hz Max, 55W

Features

I/O VGA, DVI (HDCP), HDMI, AUDIO IN
SPEAKER OUTPUT 3 Watt x 2
Compliance UL, CE, FCC-B, Energy Star, CTUVus, FCC-B

*Specifications are subject to change without notice.

Page28 SCEPTRE X270

Call Us If You Need Help!

Products are often returned due to a technical proble m rather than a defective
product that may result in unnecessary shipping charges billed to you. Our
trained support personnel can often resolve the problem over the phone or email.
For more information on warranty services or repairs after the warranty period,
please contact our support department at the number below.

For technical help, contact our SCEPTRE Technical Support Group via email or
phone. Please have your SCEPTRE p/n number, serial number, and date of
purchase available before you call.

Tech Support E-mail : [e-mail]

Customer Service Email : [e-mail]

TEL : [phone]

Operation Hours : Mon - Fri at 8:30 AM – 5:30 PM (PST)

16800 East Gale Ave.
City of Industry, CA 91745
TEL : [phone]
FAX : [phone]
Website : www.SCEPTRE.com

SCEPTRE X270 Page29

LIMITED PRODUCT WARRANTY

Please read this warranty card carefully, it is a “ONE-YEAR LIMITED WARRANTY” on parts and labor
and is only valid when purchased from an Authorized Reseller, only on new and non-refurbished
product, and available to customers in the Continental US, Alaska, Hawaii and Puerto Rico. See below
for the SCEPTRE Extended Service warranty.

SCEPTRE’s Responsibility

SCEPTRE Displays purchased in the United States are warranted to be free from defects in materials
or workmanship for a period of one (1) year from the date of their original retail purchase. If the unit
fails to conform to this warranty, we will service the monitor using new or refurbished parts.

Service Labor

During a period of one (1) year from the effective warranty date, SCEPTRE will provide, when needed,
service labor to repair a manufacturing defect at SCEPTRE’s own Service Center. To obtain warranty
service in the Untied States, you must first call our Customer Support at [phone]. The
determination of service will be made by SCEPTRE Customer Support. PLEASE DO NOT
RETURN YOUR UNIT TO SCEPTRE WITHOUT PRIOR AUTHORIZATION.

Parts

New or remanufactured replacements for defective parts will be used for repairs by SCEPTRE at its
designated Service Center for one (1) year from the effective warranty date. Such replacement parts
are warranted for the remaining portion of the original warranty period.

Service

During the one (1) year warranty period, SCEPTRE will, at its option and sole discretion, repair or
replace defective parts, including replacement of the entire Panel. The Customer will be required to
ship the unit to the Service Center indicated at the time Customer Support is contacted to make the
necessary repairs, you are responsible for all transportation charges to the service facility. SCEPTRE
is NOT responsible for the de-installation or re-installation of the unit.

Packaging and Shipping Instruction

When you send the product to an authorized SCEPTRE service facility you must use the original
carton box and packing material or an equivalent as designated by SCEPTRE.

Not Covered

This warranty does not cover defects, malfunctions or failures resulting from shipping or transit
accidents, abuse, misuse, operation contrary to furnished instructions, operation on incorrect power
supplies, operation with faulty associated equipment, modification, alteration, improper servicing,
tampering or normal wear and tear or TVs on which the serial number has been removed or defaced.
Image Sticking caused by operating at excessive brightness levels for extended periods or
mishandling are not covered by this warranty.

ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN

DURATION TO THE PERIOD OF TIME SET FORTH ABOVE. OUR LIABILITY FOR ANY AND ALL
LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, INCLUDING OUR
NEGLIGENCE, ALLEGED DAMAGE OR DEFECTIVE GOODS, WHETHER SUCH DEFECTS ARE
DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE
DISPLAY. WE SHALL NOT BE RESPONSIBLE FOR LOSS OF USE, COMMERCIAL LOSS OR
OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW

Page30 SCEPTRE X270

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. This is the only warranty applicable; no one
is authorized to extend or modify it or to grant any other warranty.
SCEPTRE retains the right to assess all warranty claims and to determine if damages are covered by
the warranty. In case of a claim that is not covered by the warranty, you will be contacted to determine
whether SCEPTRE should repair the damage for a fee or whether the product should be returned to
you as received by the repair center.

Dead Pixel Policy
There are millions of pixels on a LCD screen. Therefore, there is industry standard specification
regarding dead or bad pixels. SCEPTRE sets limit on the LCD at 3 dead pixels in a cluster adjacent to
each other, 5 dead pixels of the same brightness and color, or 8 total in a combination of color and
brightness of dead pixels. Any number of dead or bad pixels under the limit is considered normal
specification.

Owner’s Responsibility

Effective Warranty Date
Warranty begins on the date of sale to the end user. To ensure warranty service, keep the dated bill or
sale receipt as evidence of the purchase date.

Warranty Service

For warranty service information, contact SCEPTRE Customer Support at [phone], 8:30 am to
5:30 pm PST or visit www.SCEPTRE.com. Parts and service labor that are SCEPTRE’s responsibility
(see above) will be provided without charge. Other service is at the owner’s expense. You must
provide the model, serial number and date of purchase. Before you ask for warranty service, read your
User Manual. You might avoid a service call.
Warranty conditions are subject to change, for latest Warranty Terms and Conditions and additional
information regarding your warranty, please see complete details online at www.SCEPTRE.com.

SCEPTRE Extended Warranty

Protect your investment beyond the standard warranty and experience piece of mind with SCEPTRE’s
Extended Service Warranty.
Depending on your model, plans are offered for an additional 2 years. Visit www.SCEPTRE.com or call
1-800-788-2878 to purchase a plan today.

SCEPTRE X270 Page31

Disclaimer & Copyright Information

Microsoft, Windows are registered trademarks of Microsoft Corporation in the
United States and other countries.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.

HDCP is a trademark or registered trademark of Digital Content Protection, LLC.
Sceptre, Inc. shall not be liable for technical or editorial errors or omissions

contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, Sceptre, Inc. reserves the right
to change product specifications without notice. Information in this document may
change without notice.

No part of this document may be copied, reproduced, or transmitted by any
means, for any purpose without prior written permission from Sceptre, Inc..

SCEPTRE is a trademark or registered trademark of Sceptre Group.

Page32 SCEPTRE X270