SCANSTRUT SC-USB-F4 User guide

17-011-2023 (Issue 1)

Ø32mm

(1.25”)

3mm (0.11”) Min
25mm (1”) Max

90°

TOP

TOP

FLIP PRO PLUS - FAST CHARGE USB-A & USB-C SOCKET (SC-USB-F4)

(not illustrated)

SC-USB-F4-001 Deutsch Connector
SC-USB-F4-002 Flying Lead

Installation Instructions

Technical information:

Input voltage

12/24V system

Input current

max

(12V system) (24V system)

USB-A USB-C USB-A USB-C

Output type

5V⎓3A,
9V⎓3A,

12V⎓3A

MAX

Standby draw < 0.1W

Waterproof

rating

10-32V DC

6A

5V⎓3A,
9V⎓3A,
12V⎓3A

MAX

IPX4 front only lid closed

5V⎓3A,
9V⎓3A,

12V⎓3A

MAX

5V⎓3A,

9V⎓3A,
12V⎓3A,
15V⎓3A,

20V⎓3A

MAX

Parts list:

USB charger Gasket Lock ring

Front install only

Front t bezel

For latest tech info visit: www.scanstrut.com/USB

READ IMPORTANT SAFETY INFORMATION BEFORE
INSTALLING.

FRONT INSTALL ONLY

1 2 3

Draw a ce ntre lin e to align te mplate,
ensur e line is s quare o n surf ace and
correct orientatio n.

Use drilling template to drill ø32mm
(1 1/4”) hole.

x1 x1

No.6x20mm

screws

x1

x2

FRONT INSTALL ONLY

Drill 2 p ilot ho les for f ront t bezel.

Pilot Hole Size

Material No. 6 Screw

Soft Material e.g Plywood 2.5mm (3/32”)

Hard Material e.g Fiberglass 3mm (1/8”)

Tool list:

32mm (1 1/4”) Hole saw Drill

x1

Front install only

Drill bit 2.5mm (3/32”) or
3mm (1/8”) Pozi Screwdriver

Silicone

Feed ba rrel through th e gasket a nd

4

hole.

REAR INSTALL ONLY
Tighte n lock ring onto pr oduct until
secur e.

FRONT INSTALL ONLY

Apply s ilic one sea l on xings and pilot hol es. Place the
front t b ezel over c harge r and x b ezel in pl ace. Make
sure the bezel orientation is correct.

UK & International

[phone]

[e-mail]

Conne ct to 12/24V supply, en surin g a waterp roof

6 5

conne ction. Fu se and select c able di ameter a ccord ing

to input vo ltage a nd cur rent for yo ur spec ic

installation.

For further installation

and warranty information

please visit:

www.scanstrut.com

USA

[phone]

[e-mail]

17-011-2023 (Issue 1)

50mm

2”

55.0mm

(2.17”)

ø32.0mm

1mm (6/64”)

(ø1.26 ”)

BEZEL 68.1mm

(2.68”)

BEZEL 51.0mm

(2.01”)

42.0mm

(1.65”)

44.1mm

(1.73”)

TOP

FLIP PRO PLUS - FAST CHARGE USB-A & USB-C SOCKET (SC-USB-F4)

(not illustrated)

SC-USB-F4-001 Deutsch Connector
SC-USB-F4-002 Flying Lead

Drilling template:

WARNING CHECK SCALE 1:1

Installation Instructions

WARNING:
This product is to be connected to a 12V DC or 24V
DC battery power source only. The power supply
must be switched off before installation.

An appropriate fuse or circuit breaker must be
used between the battery / power source and this
product. Check for correct polarity of all wiring before
switching the power on.

This product may contain high voltages. Do not
tamper with the product.

This product is NOT approved for use in hazardous/
ammable atmospheres.

DO NOT install in a hazardous/ammable

atmosphere e.g. engine room.

Before drilling any holes, ensure the area behind the
mounting location is clear of wires, fuel and all other

hazardous objects.

Ensure any holes cut will not signicantly weaken the

structure of the mounting surface.

If the product needs to be mounted outside, it must
be mounted in a location safely above the waterline,
where it is not at risk of being submerged.

CAUTION:
The product is specially designed
for charging QC and PD compatible devices.

This product does not contain any user serviceable
parts. DO NOT attempt to repair or modify the
product in any way.

When used in high ambient temperature or in direct
sunlight, the product may turn off temporarily, this is
a safety feature of the electronics.

The IP protection rating is only valid if the installation
is carried out correctly according to the instructions

and on a perfectly at, smooth and non-porous

surface.

When choosing a mounting location, avoid areas

exposed to heat radiation devices and areas with

poor ventilation.

WIRING:
Professional electrician installation recommended,
see Technical Information for power requirements.

To achieve max power output, the specied voltage

must be at the charger. Battery performance and
voltage drop needs to be considered for installation.

ENVIRONMENTAL PROTECTION:
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities

exist. Check with your Local Authority or retailer for

recycling advice.

IMPORTANT:

Scanstrut Ltd & Inc. accepts no responsibility for any
injuries or other damages arising from the use of their

products in any circumstances.

WARRANTY:
A 2 year, non-transferrable warranty covers this
Scanstrut product only and not any devices that are
charged by it. No warranty is given for users’ devices

and users expose their devices to hazards, known or

unknown, at their own risk.

Certication.

Scanstrut Ltd, declares the product

‘Flip Pro Plus’ SKU: SC-USB-F4 is in compliance with EMC CE-RED Directive (2014/30/EU) & The CE
certicate of EN55032, EN55035, EN61000 conformity can be found at

www.scanstrut.com/support/compliance

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

Any Changes or modications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top

surface of the device must be respected.

UK & International

[phone]

[e-mail]

For further installation

and warranty information

please visit:

www.scanstrut.com

USA

[phone]

[e-mail]