Page 1
3mm Min
Ø29mm
29-09-2021 (Issue 1)
Flip Pro Fast Charge Dual USB Socket - (SC-USB-F1)
Technical information.
Input voltage 12/24V System 10-32V DC
Input current Max 6 A
x1
12V 36W
24V 60W
12V 36W
24V 36W
Lock Ring
Tools Required:
29mm (1 1/8”) Hole saw
x1
Output Type C Max
Output Type A Max
Standby draw 0.01W
Waterproof rating IPX4
Certication CE, FCC, C-Tick, ROHS
For latest tech info visit: www.scanstrut.com/USB
READ IMPORTANT SAFETY INFORMATION
BEORE INSTALLING.
Part List:
SC-USB-F1
x1
Drilling Template
WARNING CHECK SCALE
50mm 2”
WARNING:
This product is to be connected to a 12V DC or 24V DC battery power
source only. The power supply must be switched off before installation.
An appropriate fuse or circuit breaker must be used between the
battery/power source and this product. Check for correct polarity of all
wiring before switching the power on.
This product may contain high voltages. Do not tamper with the product.
17mm
(0.672)
Scale 1:1
29mm
(1.14”)
2.5mm
(0.1”)
x1
Gasket
1
Use drilling template to drill 1 x 2.5mm
(3/32”) to a depth between 1-2mm, do
not go through the mounting surface (see
tools required).
33mm Max
Ø 2.5mm Max
VERY IMPORTANT
1-2mm
– Feed SC-USB-F1 through the gasket
3 4
and hole.
– Orientate product using positioning
hole.
– Tighten lock ring onto product until
securely xed.
2.5mm (3/32”) Drill bit
Use drilling template to drill ø29mm (1
2
x1
1/8”) hole (see tools required).
Connect to 12/24V supply, ensuring a
waterproof connection. Fuse and select
cable diameter according to input voltage
and current for your specic installation.
This product is NOT approved for use in hazardous/ammable
atmospheres. Do NOT install in a hazardous/ammable atmosphere e.g.
engine room.
Before drilling any holes, ensure the area behind the mounting location
is clear of wires, fuel and all other hazardous objects.
Ensure any holes cut will not signicantly weaken the structure of the
mounting surface.
If the product needs to be mounted outside, it must be mounted in
a location safely above the waterline, where it is not at risk of being
submerged.
CAUTION:
The product is specially designed
for charging QC and PD compatible devices.
This product does not contain any user serviceable parts. DO NOT
attempt to repair or modify the product in any way.
When used in high ambient temperature or in direct sunlight, the
product may turn off temporarily, this is a safety feature of the
electronics.
The IP protection rating is only valid if the installation is carried out
correctly according to the instructions and on a perfectly at, smooth
and non-porous surface.
When choosing a mounting location, avoid areas exposed to heat
radiation devices and areas with poor ventilation
WIRING:
Professional electrician installation recommended, see Technical
Information for power requirements.
To achieve max power output, the specied voltage must be at the
charger. Battery performance and voltage drop needs to be considered
for installation.
ENVIRONMENTAL PROTECTION:
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.
IMPORTANT:
Scanstrut Ltd & Inc. accepts no responsibility for any injuries or other
damages arising from the use of their products in any circumstances.
WARRANTY:
A 2 year, non-transferrable warranty covers this Scanstrut product only
and not any devices that are charged by it. No warranty is given for
users’ devices and users expose their devices to hazards, known or
unknown, at their own risk.
Loading...