SCANSTRUT SC-USB-03 User guide

Scanstrut ROKK Charge Pro - SC-USB-03

Ø29mm

3mm Min
25mm Max

19-01-2023 (Issue 2)

Installation Instructions

Part List

Shell Gasket Lock Ring No.6 x 16X1 X1 X1 X1

1

Mark hole centre for drilling

Tools Required

ø2.5mm (3/32")

Drill Bit

ø29mm (1 1/8")

Hole Saw

- Feed SC-USB-03 through the gasket and hole.

3

- Tighten lock ring onto product until securely xed.

- Screw product into place.

Pozi Screwdriver

Silicone

Drill mounting holes (see tools required).

2

ø29mm (1 1/8")

Pilot Hole Size

Material No. 6 Screw

Soft Material e.g Plywood 2.5mm (3/32")

Hard Material e.g Fiberglass 3mm (1/8")

Connect to 12/24V supply, ensuring a waterproof connection. Fuse

4

and select cable diameter according to input voltage and current
for your specic installation.

For further installation

UK & International

[phone]

[e-mail]

and warranty information

please visit:

www.scanstrut.com

USA

[phone]

[e-mail]

Scanstrut ROKK Charge Pro - SC-USB-03

Ø 29 mm

2"

19-01-2023 (Issue 2)

Installation Instructions

Technical information.

Input voltage

12/24V System

Input current Max 6 A

Output Type C

(12V System)

Output Type C

(24V System)

Output Type A MAX 5V⎓1.5A, 9V⎓1.5A, 12V ⎓1.5A/3A MAX

Standby draw 0.01W

Waterproof rating IPX6

Certication CE, FCC, C-Tick, ROHS, UKCA

5V⎓3A, 9V⎓3A, 12V⎓3A, 15V⎓ 3A, 20V⎓ 3A MAX

READ IMPORTANT SAFETY INFORMATION BEFORE INSTALLING.

WARNING:
This product is to be connected to a 12V
DC or 24V DC battery power source only.
The power supply must be switched off
before installation.

An appropriate fuse or circuit breaker
must be used between the battery /
power source and this product. Check
for correct polarity of all wiring before
switching the power on.

This product may contain high voltages.
Do not tamper with the product.

This product is NOT approved for use in
hazardous/ammable atmospheres.
Do NOT install in a hazardous/ammable
atmosphere e.g. engine room.

Before drilling any holes, ensure the area
behind the mounting location is clear
of wires, fuel and all other hazardous
objects.

Ensure any holes cut will not signicantly
weaken the structure of the mounting
surface.

If the product needs to be mounted
outside, it must be mounted in a location
safely above the waterline, where it is not
at risk of being submerged.

CAUTION:

This product does not contain any user
serviceable parts. DO NOT attempt to
repair or modify the product in any way.

When used in high ambient temperature
or in direct sunlight, the product may turn
off temporarily, this is a safety feature of
the electronics.

The IP protection rating is only valid if
the installation is carried out correctly

10-32V DC

5V⎓3A, 9V⎓3A, 12V⎓3A MAX

according to the instructions and on a
perfectly at, smooth and non-porous
surface.
When choosing a mounting location, avoid
areas exposed to heat radiation devices
and areas with poor ventilation

WIRING:
Professional electrician installation
recommended, see Technical Information
for power requirements.

To achieve max power output, the
specied voltage must be at the charger.
Battery performance and voltage drop
needs to be considered for installation.

ENVIRONMENTAL PROTECTION:
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for recycling
advice.

IMPORTANT:
Scanstrut Ltd & Inc. accepts no
responsibility for any injuries or other
damages arising from the use of their
products in any circumstances.

WARRANTY:
A 2 year, non-transferrable warranty covers
this Scanstrut product only and not any
devices that are charged by it. No warranty
is given for users’ devices and users
expose their devices to hazards, known or
unknown, at their own risk.

CE Warning

Scanstut Ltd, declares the product ‘ROKK
CHARGE+’ SKU: SC-USB-03 is in compliance
with EMC CE Directive (2014/30/EC).

The CE certicate of conformity can be found at
www.scanstrut.com/uk/compliance.

Cutting Template

1:1 Scale

(1 1/8")

43.5 mm

(1.7")

Ø 2.5 mm
(3/32")

50 mm

Print document 1:1

Scale for correct cutting

template size.

UK & International

[phone]

[e-mail]

For further installation

and warranty information

please visit:

www.scanstrut.com

USA

[phone]

[e-mail]