SCANSTRUT SC-MULTI-F1 User guide

17-05-2023 (Issue 2)

90°

TOP

Ø32mm

(1.25”)

3mm (0.11”) Min
25mm (1”) Max

FLIP PRO MAX-DUAL USB-C & 12V POWER SOCKET
(SC-MULTI-F1)

Installation Instructions

Technical information:

USB Charger 12V Socket

Input

voltage

Input

current Max

Output Type

Standby

draw

For latest tech info visit: www.scanstrut.com/USB

Draw a centre line to align template,

1

ensure line is square on surface and
correct orientation.

12/24V System

10-32V DC

6 A 10 A

(12V System) (24V System)

5V⎓3A,
9V⎓3A,

12V⎓3A MAX

READ IMPORTANT SAFETY
INFORMATION BEFORE INSTALLING.

5V⎓3A,

9V⎓3A,
12V⎓3A,
15V⎓3A,

20V⎓3A MAX

< 0.1W

12V System

10-15V DC

12V⎓10A

2

Parts list:

2 Socket & USB
Charger Gasket Lock Ring

x1 x1

Front install only

Front Fit Bezel

No.6x20mm
Screws Screw Cover

x1

x4

Use drilling template to drill x2 Ø32mm
(1 1/4”) holes (see tools required).

Tool list:

32mm (1 1/4”) Hole saw Drill

Front install only

x2

Drill bit 2.5mm (3/32”) or
3mm (1/8”) Pozi Screwdriver

Silicone

x2

Feed Barrel through the gasket and

3

holes.

REAR INSTALL ONLY

4

Tighten lock rings onto product until

FRONT INSTALL ONLY

6

Apply silicone seal on xings and pilot
holes.

FRONT INSTALL ONLY
Push bezel onto the product, make sure

TOP

Connect to 12V supply, ensuring a waterproof

7

connection. Fuse and select cable diameter
according to input voltage and current for your
specic installation.

** If using a 24V system a voltage converter is

required on the 12V socket only**

FRONT INSTALL ONLY

5

Drill 4 pilot holes for bezel.

Pilot Hole Size

Material No. 6 Screw

Soft Material e.g Plywood 2.5mm (3/32”)

Hard Material e.g Fiberglass 3mm (1/8”)

UK & International

[phone]

[e-mail]

For further installation

and warranty information

please visit:

www.scanstrut.com

USA

[phone]

[e-mail]

17-05-2023 (Issue 2)

FLIP PRO MAX-DUAL USB-C & 12V POWER SOCKET
(SC-MULTI-F1)

Drill Template:

WARNING CHECK SCALE.

92.0mm (3.62”)

38mm (1.5”)

Installation Instructions

2”

50mm

Ø 33.0mm

(1.26”)

13.5mm (0.53”)

25.0mm (1”)

WARNING:
This product is to be connected to a 12V DC or
24V DC battery power source only. The power
supply must be switched off before installation.

An appropriate fuse or circuit breaker must be
used between the battery / power source and this
product. Check for correct polarity of all wiring
before switching the power on.

This product may contain high voltages. Do not
tamper with the product.

This product is NOT approved for use in
hazardous/ammable atmospheres.

Do NOT install in a hazardous/ammable
atmosphere e.g. engine room.

Before drilling any holes, ensure the area behind
the mounting location is clear of wires, fuel and all
other hazardous objects.

Ensure any holes cut will not signicantly weaken
the structure of the mounting surface.

If the product needs to be mounted outside,
it must be mounted in a location safely above
the waterline, where it is not at risk of being
submerged.

CAUTION:
The product is specially designed
for charging QC and PD compatible devices and
12v plug only.

This product does not contain any user serviceable
parts. DO NOT attempt to repair or modify the
product in any way.

When used in high ambient temperature or

TOP

80.0mm (3.15”)

Bezel 107.3mm (4.22”)

in direct sunlight, the product may turn off
temporarily, this

is a safety feature of the electronics.

The IP protection rating is only valid if the
installation is carried out correctly according to the
instructions and on a perfectly at, smooth and
non-porous surface.

When choosing a mounting location, avoid areas
exposed to heat radiation devices and areas with
poor ventilation

WIRING:
Professional electrician installation recommended,
see Technical Information for power requirements.

To achieve max power output, the specied
voltage must be at the charger. Battery
performance and voltage drop needs to be
considered for installation.

ENVIRONMENTAL PROTECTION:
Waste electrical products should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your Local Authority or
retailer for recycling advice.

IMPORTANT:
Scanstrut Ltd & Inc. accepts no responsibility for
any injuries or other damages arising from the use
of their products in any circumstances.

WARRANTY:
A 2 year, non-transferrable warranty covers this
Scanstrut product only and not any devices that
are charged by it. No warranty is given for users’
devices and users expose their devices to hazards,
known or unknown, at their own risk.

44.0mm (1.73”)
Bezel 107.3mm (2.01”)

Certication.

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Any Changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top
surface of the device must be respected.

Scanstrut Ltd, declares the product
‘Flip Pro Max’ SKU: SC-MULTI-F1 is in compliance with EMC CE-RED Directive (2014/30/EU) & The CE

certicate of EN55032, EN55035, EN61000 conformity can be found at

www.scanstrut.com/uk/compliance

UK & International

[phone]

[e-mail]

For further installation

and warranty information

please visit:

www.scanstrut.com

USA

[phone]

[e-mail]