Scanreco TR03G44FH917, TR03G4PWMFH917, TR03G410FH917 User Manual

Instruction Manual

Remote Control system RC400

Document no Revision Language

S106

A English

Document type Document number Rev Page

Manual S106 A 2 of 18

Contents

1 General ................................................................................. 3

1.1 Terminology 3

2 Preface ................................................................................. 4

2.1 General information 4

2.2 Notice and Warnings 5

3 General system description.................................................... 6

3.1 Schematic overview of Scanreco RC-400 G4 6

3.2 Portable Control Unit 7

3.3 Portable Control Unit Handy 12

3.4 Central unit (CU) 16

4 Safety regulations and operating instructions .......................17

4.1 Safety regulations 17

4.2 Operating instructions 18

All rights reserved.

Design, equipment, technical data and specification are subject to change or improvement
without prior notice. The text of this manual, or any part thereof, may not be reproduced or
transmitted in any form or by any means, electronic or mechanical including photocopying,
recording, storage in an information retrieval syst
permission of Scanreco AB, Sweden.

em, or otherwise, without the prior written

Document type Document number Rev Page

Manual S106 A 3 of 18

Document information

Attribute Information

Document type

Title

Subtitle

Document number

Revision

Revision date

Manual

Instruction manual

Remote Control System Scanreco RC-400 G4

S106

A

2009-09-25

Revision history

Revision Date Name Note

A 2009-09-25 SCANRECO AB First creation of document

1 General

1.1 Terminology

Abbreviation Description

PCU Portable Control Unit

CU Central Unit

LED Light Emitting Diode

DV Dump Valve

Document type Document number Rev Page

Manual S106 A 4 of 18

2Preface

2.1 General information

This manual is intended as a complement to the crane / machine instruction book
and covers the Scanreco RC 400 Remote Control System.

The Scanreco RC 400 offers the driver an extremely advanced remote control system
with speed, precision, control and maximum safety.

In order to ensure your safety and the safety of your crane / machine you should
study and learn these instructions. This will enable you to quickly familiarise yourself
with your new remote control system and how to utilise it.

% Remotely controlled cranes may only be operated by qualified p

driver must be aware of the contents of chapter 4 "Safety regulations and
Operating instructions" before operation is started. Serious accidents may
occur if these instructions are not followed.

% To protect the portable control unit from damage and for safety reasons, the

control unit must be kept in a locked cab.

% Follow the instructions given in the crane handbook regarding moving the

crane from its parking position, the best arm positioning while loads are being
handled and parking of the crane.

% Due to the unlimited variety of cranes, machin

equipment on which the remote control system are used, and the numerous
standards which are frequently the subject of varying interpretation, it is
impossible for the personnel at Scanreco to provide expert advice regarding
the suitability of a given remote control for a specific application. It is the
responsibility of the purchaser to determine the suitability of any Scanreco
remote control product for an intended application and to insure that it is
installed and guarded in accordance with all country, federal, state, local, and
private safe
recommendation (this manual). If the Scanreco RC 400 G4 will be used in a
safety critical application, the customer / driver must undertake appropriate
testing and evaluation to prevent injury to the ultimate user. Scanreco does
not take responsibility for any damage or injure

% Unauthorized tampering with Scanreco automatically invalidates guarantee.

To the operator:

ty and health regulation, codes, standards and Scanreco

es, objects, vehicles and

ersonnel. The

Pause for a while and give yourself extra time to read chapters 3 (General system
description) and 4 (Safety regulations and Operating instructions).

the installer:

To

Pause for a while and give yourself extra time to read chapters 5 (Installation
instructions) and "Inspection / Installation documents”.

Document type Document number Rev Page

Manual S106 A 5 of 18

2.2 Notice and Warnings

Thisequipmentcomplieswithpart15oftheFCC Rulesand RSS-210ofIC Rules.
Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Changes or

modifications not expressly approved by Scanreco Industrielektronik AB will void
the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuan

provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off
try to correct the interference by one or more of the following measures:

%Reorient or relocate the receiving antenna.
%Increase the separation between the equipment and receiver.

%Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

%Consult the dealer or an experienced radio/TV technician for help.

t to Part 15 of the FCC Rules. These limits are designed to

and on, the user is encouraged to

Document type Document number Rev Page

Manual S106 A 6 of 18

3 General system description

3.1 Schematic overview of Scanreco RC-400 G4

The Remote Control System is comprised of the following components (see figure

3.1):

1

1

2

3

Figure 3.1 Schematic overview of the Scanreco RC-400 G4.

General scope of delivery (see your specification and Figure 3.1).

No Description Qty

1 Portable Control unit (PCU) Chapter 3.2 1

1 Portable Control Unit Handy (PCU-H) Chapter 3.3 1

2 Central unit (CU) Chapter 3.4 1

3 Emergency stop box (Optional) 1

4 Cable kit supply cables + digital outputs 1

5 Cable kit valves cables (analogue outputs) 1

4

5