SD 46
SD 76
SD 92
User manual
Scandomestic A/S · Thrigesvej 2 · DK-8600 Silkeborg
T + 45 7242 5571 · F + 45 8622 5571 · scandomestic.dk
TRANSPORTATION AND INSTALLATION
1 Place on level oor and remove the bottom packing, in order
to decrease the shock and noise.
The angle between the compartment body and ground
should be no more than 45°
2 Enough space should be left between the freeze and the
wall for ventilation.
3 Place the freezer away from heat source and do not expose
to direct sunshine.
4 Do not install where there is moisture or where it can easily
be splashed by water.
5 Do not place the freezer in environment prone to freezing.
6 The appliance should not be used in open air and should not
be exposed to rain.
FREEZING METHODS
1 Do not put too much food into the freezer or exceed the
loading line.
2 proper space should be allowed between foods to ensure
cooling air circulation.
3 Never use corrosive detergent, hot water, or washing power
to clean the freezer.
4 Do not use water to scour the freezer. Do not use hard bru-
shes or wire brushes to clean the freezer.
5 Do not use metal or sharp tools for defrosting.
6 Do not use electric heaters to heat up and defrost.
7 The green lamp is a power indicating lamp. When the power
is on, the lamp will be on.
ADJUSTMENT AND RUNNING
1 Adjustment of temperature: The storing temperature can be
adjusted by the thermostat of the compartment. The thermostat should be adjusted according to different environment temperature and the food by rotating the knob of the
thermostat. The knob rotates clockwise from ”1” to “7”(or
direction arc)and the inside temperature turns down in
summer (anti-clockwise rotation)and up in winter(clockwise
rotation). It is usually xed to a certain point before leaving
the factory. Do not adjust too often or touch the other parts.
2 Trial running: plug in and wait. The marked drop in tempe-
rature within half an hour indicates that the freezer works
properly.
The compressor should be left to run for a period of time(6
hours in summer 4 hours in winter )before putting the food
in.
SAFETY PRECAUTIONS
1 The freezer should use a single 3-pin socket with (13A)fuse.
A multi –plug outlet should not be used.
2 You should install a suitable automatic voltage regulator not
less than 500w when the voltage is outside the range from
187V to 242V.
3 The sockets of the freezer should be connected to stable
xed connection. Under no circumstance should the wiring
be connected to such facilities as water pipe, gas pipe and
so on.
4 Once power is cut off, wait for at least 5 minutes before
plugging in again to avoid damaging the compressor or the
system.
5 Do not put combustible ,explosive or volatile dangerous
articles, heavily corrosive acid or alkali of liquid in glassware
into the freezer.
6 Children should be kept away from the freezer to avoid da-
mage to the inner container or any accidents being incurred
7 If the power cable damages, for avoid dangerous, must by
manufactory or its maintain a set or similar profession job
the personnel replaces.
TROUBLE SHOOTING:
The design and production comply with the relative security
standard of China. If you nd it does not work as usual, please
examine and handle it according to the following table rst. If
the situation does not improve, you must contact our after-sale
service center or our special repair division to examine and repair
the appliance.
The following problems are not causes of breakdown:
There is a sound of liquid owing in the freezer It is the
sound of refrigerant owing in the circulating pipeline of the
refrigerating system.
- It is normal.
Too noisy
- The freezer is not installed in a level ground.
- Change the position.
The refrigerating system does not work for a It is an indicator
of high quality for its long time but the inside temperature is
very good insulation and low cooling retention low.
- It is normal.
2
Trouble Possibilities Check up Solutions Remarks
Compressor
does not work
Compressor keeps on
working
Too noisy The oor is not level Make sure that the
Power is off The fuse is broken Check the fuse Replace the fuse If it is necessary plea-
The connection between plug and socket
is not good
The circuit of input and
output is out of use
The thermostat knob is not in the
proper position
The temperature inside
is too high
The temperature inside
is OK
The screw in fan or condenser is loose The screw is loose Rotate the xed screw
The refrigerating circuits touch each
other
Frost on the evaporator
is too thick
The door is being opened too frequently
Too much food has
been stored at once
The ambient temperature is too high .while
the thermostat indicates a small number
The thermostat does
not work
Check the socket Repair or replace the
Make sure that the
power is on
Check the thermostat Rotate the thermo-
Check whether the
frost is thicker than
6-8mm
Make sure whether
the knob is indicating at the“5-6”(or
deeper)
freezer is level
socket
Check the circuit with
electric instrument
statto the proper
position
Defrost regularly
Reduce the times of
opening
Take out some of the
food
Adjust the thermostat
knob
Replace the thermostat
Put pad under the
castors
Separate them
se contact after-sales
service for repair
Ask for professional
help
The thermostat knob
on”2-4”is better(or
proper)
Ask for after-sales
service
3
Circuit diagram
4
Loading...