SCAN 83-8,Scan 83-7,Scan 83-6,Scan 83-5,Scan 83-4,Scan 83-3,Scan 83-2,Scan 83-1,83 series,83-8 Assembly And Instruction Manual
SCAN A/S - DK-5492 VISSENBJERG
Scan 83 Series
ASSEMBLY AND INSTRUCTION MANUAL
Congratulations on your new Scan wood-burning stove
You have purchased a product by one of Europe’s leading manufacturer’s of wood-burning stoves, and we are sure that you will have years of
pleasure with your purchase. To make the best possible use of your stove, it is important that you follow our advice and instructions.
Read through this Assembly and Instruction Manual carefully before you start to assemble your stove.
Product registration number
Please indicate the product registration number at any
enquiry
CONTENTS
Table of contents
Technical data ................................................................................................... 3
Installation
Safety
Certificate of testing
Technical data and dimensions
Dimensional drawings
Type plate
Product registration number
Assembly ........................................................................................................... 10
Additional accessories
Loose parts
Removal of packaging
Disposal of packaging
Height adjustment of stove
Fresh air intake
Closed combustion system
Load-bearing subsurface
Floor plate
Existing chimney and pre-fabricated element chimney
Connection between stove and steel chimney
Requirements for chimney
Connection with 90° elbow pipe
Rotating base and 90° elbow pipe
Erection
Distance to flammable materials
Fitting the flue connection piece in the top outlet
Fitting the flue connection piece in the rear outlet
Adjusting the height of the top module
Fitting the natural stone sides
Fitting the natural stone top
Heat-storage stone Scan 83 Maxi models
Fitting the tile sides
Instructions for use ....................................................................................... 25
CB technology
Primary air
Secondary air
Baffle plates
Ash container
Handle for riddling grate
Instructions for operation .......................................................................... 27
Lighting
Handling fuel
Maintenance ................................................................................................... 29
Troubleshooting ............................................................................................. 33
2
TECHNICAL DATA
Installation
The house owner is responsible for ensuring that installation and
assembly are in accordance with national and local building regulations as well as the information provided in this Assembly and
Instruction Manual.
When you install any kind of fireplace or stove, you must inform the
local building and housing authorities. In addition you are obliged
to have the installation inspected and approved by a local chimney
sweep prior to commissioning.
To ensure best-possible functionality and safety for your installation,
we advise you to call a professional fitter. Your Scan Dealer will be
able to recommend a qualified fitter in your area. For information on
Scan Dealers, please go to http:// scan.dk.
The Scan 83 Series comprises:
Scan 83-1: Stove with handles and trims in black aluminium
Scan 83-2: Stove with handles and trims in brushed aluminium
Scan 83-3: Stove Maxi with handles and trims in black aluminium
Scan 83-4: Stove Maxi with handles and trims in brushed aluminium
Scan 83-5: Stove with natural stones/tiles, handles and trims in black aluminium
Scan 83-6: Stove with natural stones/tiles, handles and trims in brushed aluminium
Scan 83-7: Stove Maxi with natural stones, handles and trims in black aluminium
Scan 83-8: Stove Maxi with natural stones, handles and trims in brushed aluminium
Safety
Any changes made to the product by the dealer, fitter or user could
result in the product and safety functions not functioning as intended. The same applies to the fitting of accessories or extra equipment
not supplied by Scan A/S. This could also be the case if parts that are
necessary for the operation and safety of the stove are dismantled
or removed.
3
Scan 83-1 / Scan 83-2 Scan 83-3 / Scan 83-4 Scan 83-5 / Scan 83-6 Scan 83-7 / Scan 83-8
TECHNICAL DATA
Scan 83 Series Technical data Unit
CO emissions at 13% O
2
* 0.07 %
CO emissions at 13% O2
896 mg/Nm
3
Dust @ 13% O
2
23 mg/Nm
3
Nox @ 13% O
2
106 mg/Nm
3
Efficiency
81 %
Nominal output
5 kW
Chimney temperature EN 13240
227 °C
Temperature in flue connection piece
280 °C
Amount of smoke
5 g/sec
Negative pressure EN 13240
12 Pa
Recommended negative pressure in flue con-
nection piece
16 Pa
Required combustion air supply
14 Nm3/h
Fuel
Wood Wood
Fuel consumption
1.6 kg/h
Amount of fuel required to light
1.4 kg
Technical data and dimensions
Materials: ................................... Steel plate, cast iron, galvanised sheet,
vermiculite
Surface treatment: ........................................................................... Senotherm
Max. log length: ........................................................................................... 26 cm
Weight Scan 83-1 / Scan 83-2: .................................................. approx. 117 kg
Weight Scan 83-3 / Scan 83-4: .................................................approx. 125 kg
Weight Scan 83-5/6, natural stone/tile: ..................approx. 186/132 kg
Weight Scan 83-7 / Scan 83-8: ................................................ approx. 212 kg
Fresh air connection piece external diameter: .............................100 mm
Flue connection piece internal diameter: ...................................... 144 mm
Flue connection piece external diameter: ..................................... 148 mm
Approval type: ............................................................ Intermittent operation
Intermittent operation in this context means normal use of a woodburning stove. In other words, you should let the fire die down until
only the embers are left before refuelling.
The Scan 83 Series is produced in accordance with type approval for
the product, which also covers the product’s Assembly and Instruction
Manual.
The Declaration of Performance (DoP) is available from http://scan.dk
Tested in accordance with EN 13240
4
* based on 896 mg/Nm
3
TECHNICAL DATA
Dimensional drawing for Scan 83-1 and Scan 83-2
1200
460
230
1162
*
1064
**
132
±
20
***
230****
481
* Height to beginning of
flue connection piece at
top outlet
** Centre rear outlet
*** Centre of fresh air intake
rear outlet
**** Centre of fresh air intake
bottom
5
TECHNICAL DATA
230****
1410
1162*
481
230
460
1064**
132
20
Dimensional drawing for Scan 83-3 and Scan 83-4
* Height to beginning of
flue connection piece at
top outlet
** Centre rear outlet
*** Centre of fresh air intake
rear outlet
**** Centre of fresh air intake
bottom
6
TECHNICAL DATA
Dimensional drawing for Scan 83-5 and Scan 83-6 with natural stones/tiles top module
1235
460
230
132
±
20 ***
1064
**
1162
*
230****
481
* Height to beginning of
flue connection piece at
top outlet
** Centre rear outlet
*** Centre of fresh air
intake rear outlet
**** Centre of fresh air intake
bottom
7
/1222 (tiles)
TECHNICAL DATA
1446
460
481
230
1162
*
1064
**
132
±
20 ***
230****
Dimensional drawing for Scan 83-7 and Scan 83-8 with natural stones top module
* Height to beginning of
flue connection piece
at top outlet
** Centre rear outlet
*** Centre of fresh air intake
rear outlet
**** Centre of fresh air intake
bottom
8
TECHNICAL DATA
Scan 83 - Series
Freestanding room heater fired by solid fuel
Standard:
Fuel type:
Operation type:
The appliance can be operated in a shared flue.
Country
EN 13240 EC no. 90583600
Wood
Intermittent
EUR
Norway
Austria
Classification
Intermittent
Klasse 2
15a B-VG
Certificate/Standard
EN 13240
300-ELAB-1904-NS
FSPS-Wa 2197-EN-A
Approved by
RWE Power AG
Teknologisk Institut
RWE Power AG
Dust at 13% O2: 23 mg/Nm³
Flue gas temperature: 280°C
Nominal heat output: 5 kW
Efficiency: 81%
Angaben für Österreich
Wärmeleistungsbereich: 2,6 - 5,8 kW
Brennstoffwärmeleistung: 7,2 kW
Zulässige Brennstoffe: Scheitholz
Prüfbericht:
FSPS-Wa 2197-A
Scan A/S DK 5492 Vissenbjerg
Minimum distance to combustible materials:
Side: 400 mm - Back: 100 mm - Front: 900 mm
CO emission at 13% O2:
Follow assembly- and instructions manual.
Use only recommended fuels.
DIBt Zulassungsnummer:
Montage- und Bedienungsanleitung beachten.
Verwenden Sie nur empfohlene Brennstoffe.
1000 06-2013
0,07% 896 mg/Nm³
Schweiz
Germany
LRV 11
BStV 1
VKF
FSPS-Wa 2197-EN
RWE Power AG
RWE Power AG
Type plate for Scan 83 Series
All Scan wood-burning stoves are fitted with a type plate that specifies the approval standards and the distance to flammable materials.
The type plate is located at the rear of the stove.
Type plate
Product
registration
number
Product registration number
All Scan wood-burning stoves are provided with a product registration number.
The product registration number is located at the rear of the stove.
Please make a note of this number at the frontpage; you will always
need to quote it when contacting your dealer or Scan A/S.
83XXXXX
9
ASSEMBLY
Additional accessories
• Small shapedfloor plate in glass or steel
• Large shapedfloor plate in glass or steel
• Small corner shapedfloor plate in glass or steel
• Soapstone top module for stove with rear outlet
• Soapstone top module for stove with top outlet
• Heat-storage stone Scan 83 Maxi 4 items approx.
40 kg
• Rotating base
•
Tile sides
Loose parts
The flue connection piece and other loose parts are located in the
stove’s combustion chamber.
Scan 83, all types:
• x4 screws for fastening flue connection piece
• Gasket for flue connection piece
• Glove
• Repair lacquer for coloured stoves
Scan 83-5, Scan 83-6, Scan 83-7 and Scan 83-8
• 7/9 m sealing tape
Removal of packaging
Check that the stove is not damaged before starting to install it.
The Scan 83 Series comes attached to a wooden pallet on delivery. To
remove the packaging, see the illustrations below.
Screws to be removed
Disposal of packaging
Your Scan stove may come supplied with the following packaging:
Wood packaging:
The wood packaging can be reused and after final use can be incinerated as a CO2 neutral product or sent for recycling.
Flamingotop:
Send for recycling or waste disposal.
Foam:
Send for recycling or waste disposal.
Plastic bags:
Send for recycling or waste disposal.
Stretch film/plastic film:
Send for recycling or waste disposal.
10
A
A
ASSEMBLY
Remove the screws and fittings for securing the stove to the pallet.
Lift off the front of the base.
Height adjustment of stove
The Scan 83 Series has four adjustment screws under the stove. Use
the adjustment screws to get the stove to stand straight and level.
To adjust the adjustment screws, see the illustrations below.
If you are using a shaped floor plate, you should adjust the stove
upwards to allow the plate to be inserted under the front of the stove.
11
B
B
C
C
Remove the screws for the cover plate in the base.
Screws to be removed
Loading...