Page 1
SCAN A/S-DK-5492 VISSENBJERG
Product registration number
Scan 65-series
ASSEMBLY- AND INSTRUCTIONS MANUAL
Please indicate the product registration number at any enquiry
GB
Congratulations on your new Scan wood-burning stove
You have purchased a product by one of Europe’s leading manufacturers of wood-burning stoves, and we are sure that you will have years of
pleasure with your purchase. To make the best possible use of your stove, it is important that you follow our advice and instructions.
Read through this Assembly and Instruction Manual carefully before you start to assemble your stove.
Page 2
2
Table of contents
Technical data ........................................................................................................ 3
Installation
Safety
Technical data and dimensions
Dimension sketch
Type plate
Product registration number
Additional accessories
Loose parts
Assembly ................................................................................................................9
Remove packaging
Positioning your wood-burning stove
Distance to furniture
Distance to flammable materials, shown with insulated flue pipe
Distance to flammable materials, shown with un-insulated flue pipe
Distance to firewall
Height adjustment of stove
Load bearing foundation
Floor plate
Existing chimney and pre-fabricated element chimney
Connection between stove and steel chimney
Requirements for chimney
Connection with 90° elbow pipe
Connecting piece / top outlet
Connecting piece / rear outlet
Fitting the natural stones
Fresh air intake
Closed combustion system
Indicator for control of air supply
Scan 65 open plinth
Accessories ...........................................................................................................20
Heat accumulating stones
Fitting the top plate of natural stones
Instruction for use ................................................................................................21
CB technique
Primary air
Secondary air
Baffle plates
Ash drawer
Handle for riddling grate
Instructions for heating ...................................................................................... 22
The Clean Air Act 1993
Lighting
Handling fuel
Maintenance ........................................................................................................ 24
Troubleshooting ..................................................................................................26
CONTENTS
Page 3
3
TECHNICAL DATA
Installation
The house owner is responsible for ensuring that installation and
assembly are in accordance with national and local building regulations as well as the information provided in this Assembly and
Instruction Manual.
When you install any kind of fireplace or stove, you must inform the
local building and housing authorities. In addition you are obliged
to have the installation inspected and approved by a local chimney
sweep prior to commissioning.
To ensure best-possible functionality and safety for your installation,
we advise you to call a professional fitter. Your Scan Dealer will be
able to recommend a qualified fitter in your area. For information on
Scan Dealers, please go to www.scan.dk.
The Scan 65-series consists of:
Safety
Any changes made to the product by the dealer, fitter or user
could result in the product and safety functions not functioning
as intended. The same applies to the fitting of accessories or extra
equipment not supplied by Scan A/S. This could also be the case if
parts that are necessary for the operation and safety of the stove are
dismantled or removed.
Scan 65-1
Steel sides
Scan 65-2
Steel sides
and side windows
Scan 65-1 LB
Steel sides
Scan 65-2 LB
Steel sides
and side windows
Scan 65-3
Natural stones
Scan 65-4
Natural stones
and side windows
Scan 65-5
Steel sides,
baking oven
Scan 65-6
Steel sides,
baking oven and
side windows
Scan 65-7
High Top,
natural stones
Scan 65-8
High Top,
natural stones and
side windows
Scan 65-9
High Top,
steel sides
Scan 65-10
High Top, steel sides
and side windows
Page 4
4
senotherm
30 cm
65-1 /2 ca. 123 kg
65-3 ca. 180 kg
65-4 ca. 168 kg
65-5/6 ca. 162 kg
65-7 ca. 258 kg
65-8 ca. 246 kg
65-9/10 ca. 162 kg
144 mm
148 mm
65-1, 65-3, 65-5, 65-7 & 65-9
0,08
975
< 20
104
82
110
A+
6
221
300
5
12
15-18
13,3
2
1,5
65-2, 65-4, 65-6, 65-8 & 65-10
0,1
1221
< 20
117
79
106
A
6
240
305
6
12
15-18
12,5
2
1,5
4
TECHNICAL DATA
Technical data Unit
CO Emission at 13% O2 %
CO Emission at 13% O2 mg/Nm3
Dust @ 13% O2 mg/Nm3
Nox @ 13% O2 mg/Nm3
Efficiency %
Energy efficiency index
Energy efficiency class
Nominel output kW
Chimney temperature EN 13240 °C
Temperature in connecting piece °C
Amount of smoke g/sek
Sub-pressure EN 13240 Pa
Recommended sub-pressure in connecting piece Pa
Required combustion air supply Nm3/h
Fuel Wood
Fuel consumption kg/h
Amount of fuel kg
Technical data Unit
CO Emission at 13% O2 %
CO Emission at 13% O2 mg/Nm3
Dust @ 13% O2 mg/Nm3
Nox @ 13% O2 mg/Nm3
Efficiency %
Energy efficiency index
Energy efficiency class
Nominel output kW
Chimney temperature EN 13240 °C
Temperature in connecting piece °C
Amount of smoke g/sek
Sub-pressure EN 13240 Pa
Recommended sub-pressure in connecting piece Pa
Required combustion air supply Nm3/h
Fuel Wood
Fuel consumption kg/h
Amount of fuel kg
Test in compliance with EN 13240
Technical data and dimensions
Materials Steel plate, cast iron,
galvanised sheet, vermicolite
Surface treatment
Max. wood length
Weight
Weight
Weight
Weight
Weight
Weight
Weight
Connecting piece internal diameter
Connecting piece external diameter
Approval type Intermittent fuelling*
*Intermittent operation in this context means normal use of a
wood-burning stove. In other words, you should let the fire die down
until only the embers are left before refueling.
This stove is produced in accordance with type approval for the
product, which also covers the product’s Assembly and Instruction
Manual.
The Declaration of Performance (DoP) is available from www.scan.dk
Page 5
5
65-5, 65-6, 65-7, 65-8, 65-9 & 65-10
65-1, 65-2, 65-3 & 65-4
A-A ( 1 : 10 )
Top
Bund
1
1
3
2
490
2
1
0
*
*
*
*
7
2
1
0
1
2
*
1
1
1
1
*
*
3
8
0
1
9
0
154
1
1
4
9
0
*
*
*
A-A ( 1 : 10 )
Bund
2
1
0
*
*
*
*
7
2
1
0
1
2
*
1
1
1
1
*
*
154
9
0
*
*
*
A-A ( 1 : 10 )
Bund
154
1
1
4
9
0
*
*
*
A-A ( 1 : 10 )
Top
Bund
3
8
0
1
9
0
1
1
4
9
0
*
*
*
A-A ( 1 : 10 )
Top
Bund
1
1
4
9
2
*
*
*
3
8
2
1
9
2
A-A ( 1 : 10 )
Bund
154
1
1
4
9
2
*
*
*
A-A ( 1 : 10 )
Top
Bund
1
4
3
3
490
154
1
1
4
9
2
*
*
*
1
5
8
2
1
0
*
*
*
*
1
0
9
8
*
1
4
1
5
*
*
3
8
2
1
9
2
1433 (65-5/6 + 9/10)
1448 (65-7/8)
Bund
154
1
1
4
9
2
*
*
*
1
5
8
2
1
0
*
*
*
*
1
4
1
5
*
*
A-A ( 1 : 10 )
Top
Bund
154
1
1
4
9
2
*
*
*
3
8
2
1
9
2
65-9/10
1415** (65-5/6)
1201** (65-7/8)
1196** (65-9/10)
5
TECHNICAL DATA
Dimension sketch
* Centre rear outlet
** Height to the begin ning of the connecting
piece at top outlet
*** Fresh air intake bottom
**** Fresh air intake at the
back of the stove
Page 6
6
65-1 LB & 65-2 LB
490
1
0
0
0
1
2
1
5
0
9
7
9
8
8
0
154
1
1
4
9
0
1
9
0
3
8
0
1
2
1
5
0
9
7
9
8
8
0
154
1
1
4
9
0
154
1
1
4
9
0
1
1
4
9
0
1
9
0
3
8
0
6
6
TECHNICAL DATA
* Centre rear outlet
** Height to the begin ning of the connecting
piece at top outlet
*** Fresh air intake bottom
**** Fresh air intake at the
back of the stove
Dimension sketch
* Centre rear outlet
** Height to the begin ning of the connecting
piece at top outlet
*** Fresh air intake bottom
**** Fresh air intake at the
back of the stove
Dimension sketch
Page 7
6
Scan 65-1 - 65-3 - 65-5 - 65-7 - 65-9
Freestanding room heater fired by solid fuel
Standard:
Fuel type:
Operation type:
The appliance can be operated in a shared flue.
Country
EN 13240 Dop 90065600
Wood
Intermittent
EUR
Norway
Classification
Intermittent
Certificate/Standard
EN 13240
Approved by
RWE Power AG
Teknologisk Institut
Dust at 13% O2: < 20 mg/Nm³
Flue gas temperature: 300°C
Nominal heat output: 6 kW
Efficiency: 82%
Scan A/S DK 5492 Vissenbjerg
Minimum distance to combustible materials
Side: 350 mm - Back: 150 mm - Front: 1000 mm
CO emission at 13% O2:
Follow assembly- and instructions manual.
Use only recommended fuels.
Montage- und Bedienungsanleitung beachten.
Verwenden Sie nur empfohlene Brennstoffe.
1000 05-2015
0,08% 975 mg/Nm³
Schweiz
Germany
RWE Power AG
RWE Power AG
Scan 65-2 - 65-4 - 65-6 - 65-8 - 65-10
Freestanding room heater fired by solid fuel
Standard:
Fuel type:
Operation type:
The appliance can be operated in a shared flue.
Country
EN 13240 Dop 90065601
Wood
Intermittent
EUR
Norway
Classification
Intermittent
Certificate/Standard
EN 13240
Approved by
RWE Power AG
Teknologisk Institut
Dust at 13% O2: < 20 mg/Nm³
Flue gas temperature: 305°C
Nominal heat output: 6 kW
Efficiency: 79%
Scan A/S DK 5492 Vissenbjerg
Minimum distance to combustible materials
Side: 500 mm - Back: 150 mm - Front: 1000 mm
CO emission at 13% O2:
Follow assembly- and instructions manual.
Use only recommended fuels.
Montage- und Bedienungsanleitung beachten.
Verwenden Sie nur empfohlene Brennstoffe.
1000 05-2015
0,10% 1221 mg/Nm³
Schweiz
Germany
RWE Power AG
RWE Power AG
65-2, 65-4, 65-6, 65-8 & 65-10
65-1, 65-3, 65-5,65-7 & 65-9
6500000
7
TECHNICAL DATA
(With side windows)
(Without side windows)
Type plate
Product registration number
Type plate
All Scan wood-burning stoves are fitted with a type plate that specifies the approval standards and the distance to flammable materials.
The type plate is located at the rear of the stove.
Product registration number
All Scan wood-burning stoves are provided with a product registration number. You will always need to quote this number when contacting your dealer or Scan A/S.
The product registration number is located at the rear of the stove.
Page 8
7
8
TECHNICAL DATA
Additional accessories
• Small shaped floor plate in glass or steel
• Large shaped floor plate in glass or steel
• Natural stones top plate for stove with rear outlet
• Natural stones top plate for stove with top outlet
• Heat accumulating stones (Scan 65-7, 65-8, 65-9 & 65-10)
Loose parts
The loose parts are located in the stove's ash drawer.
Scan 65, all types:
• Glove
• Seal
• 4 pcs. screws for fastening the connecting piece
• 1 pcs. indicator for control of air supply
• 1 pcs. screw M5x6, must be placed for United Kingdom.
Scan 65-3 and 65-4:
• 4,5 m gasket
Scan 65-7 and 65-8:
• 7 m gasket
Disposal of packaging
Your Scan stove may come supplied with the following packaging:
WOOD PACKAGING:
The wood packaging can be reused and after final use can be incinerated as a CO2 neutral product or sent for recycling.
FLAMINGOTOP:
Send for recycling or waste disposal.
FOAM:
Send for recycling or waste disposal.
PLASTIC BAGS:
Send for recycling or waste disposal.
STRETCH FILM/PLASTIC FILM:
Send for recycling or waste disposal.
Page 9
8
9
Screws to be removed
Remove the screws securing the stove to the pallet.
Fit the plastic plugs from the service box
into the transport protection holes.
Remove the protection between the baffle plates, before taking the
stove into use!
Protection for baffle plates
Put back the upper plate on the pins, as the protection pushes the
plate upwards.
Pin for baffle plate
ASSEMBLY
Removal of packaging
Check that the stove is not damaged before starting to install it.
The stove comes attached to a wooden pallet on delivery.
Page 10
50
500
250
250
778
5
3
6
745
240
513
50
350
2
5
3
595
240
50
50
313
578
9
65-2, 65-4, 65-6, 65-8 & 65-10
65-1, 65-3, 65-5,65-7 & 65-9
10
ASSEMBLY
Distance to flammable materials, shown with insulated flue pipe
(With side windows)
Without side windows)
Positioning your wood-burning stove
The stove must be set up so that the stove itself, the flue pipe, and the
chimney can all be cleaned.
Distance to furniture: 1000 mm
You should however assess whether furniture or other items might
become excessively dry due to being too close to the stove.
National and local regulations governing safety distances for woodburning stoves must be complied with.
If the stove is to be connected to a steel chimney, the chimney requirements in terms of safety distances must be met.
Distance to flammable materials
These distances apply for an uninsulated flue pipe/insulated flue
pipe, all the way down to the stove, having a minimum of 30 mm
insulation.
Page 11
150
500
5
3
6
250
778
250
340
745
513
150
350
340
595
100
363
628
100
3
2
4
10
65-2, 65-4, 65-6, 65-8 & 65-10 65-1, 65-3, 65-5,65-7 & 65-9
11
ASSEMBLY
Distance to flammable materials, shown with un-insulated flue pipe
(With side windows)(Without side windows)
Page 12
50
50
100
50
50
700
700
960
700
700
2
53
50
50
100
50
50
700
700
700
800
760
700
860
860
100
100
50
300
50
3
2
4
11
65-2, 65-4, 65-6, 65-8 & 65-10
65-1, 65-3, 65-5,65-7 & 65-9
12
ASSEMBLY
Flammable material
Firewall
Flammable material
Firewall
(With side windows)
Without side windows)
Distance to firewall
110 mm brick or other material with a corresponding insulation
ability.
The distances presuppose the use of an insulated flue pipe with min.
30 insulation all the way to the stove.
Page 13
12
13
ASSEMBLY
Large shaped floor plate in glass or steel
Ajustment screw
IT IS VERY IMPORTANT THAT THE STOVE IS LEVEL TO ALLOW AN
OPTIMAL FUNCTION OF THE DOOR. PLEASE NOTE THAT ONCE
MOUNTED THE STOVE CAN NO LONGER BE ADJUSTED!
Small shaped floor plate
in glass or steel
Height adjustment of stove
The stove has four adjustment screws under the stove. Use the adjustment screws to get the stove to stand straight and level.
Load-bearing subsurface
All items in our product range come under the category of lightweight
fireplaces and stoves and do not normally require any reinforcement
of the beam structure. They can be positioned on ordinary beams/
floor.
However, you should make sure that the load bearing underlay can
bear the weight of the wood-burning stove and that of the chimney.
Floor plate
If you are erecting the stove on a flammable floor, you must comply
with the national and local regulations on the size of any non-flammable subsurface required to cover the floor around the stove.
Your local Scan dealer can advise you on regulations concerning protection of flammable materials in the vicinity of your stove.
The floor plate’s function is to protect the floor and flammable material against any sparks that may occur.
A floor plate can be made of steel or glass, but the stove can also be
erected on clinker concrete, natural stone or similar materials.
This Scan wood-burning stove has an integrated floor plate at the bottom and can thus be erected directly on flammable material without
the need for further protection underneath the stove.
Page 14
13
14
ASSEMBLY
Connecting
piece
Ceramic
asket
Mount the ceramic gasket on the connecting piece
Lift the top plate and connecting piece off the stove.
Existing chimney and pre-fabricated element
chimney
If you intend to connect your stove to an existing chimney, it makes
sense to contact an authorised Scan dealer, or a local chimney sweep,
for advice. These experts will also let you know if your chimney needs
renovating.
When connecting a pre-fabricated element chimney, follow the manufacturer’s connection instructions for the relevant chimney type.
Connection between stove and steel chimney
Your Scan dealer, or local chimney sweep, can advise you on choosing a make and type of steel chimney (we recommend using JØTUL’s
chimney system). This ensures that the chimney will match your
wood-burning stove. As a general rule, the length of the chimney
should not be less than 4 metres, measured from the top of the stove.
Specific weather or installation conditions might require a different
length.
Choosing the wrong length or diameter of steel chimney could impair functionality.
Always observe the chimney vendor‘s instructions precisely.
Requirements for chimney
The chimney must be labelled T400 and G for soot testing.
Connecting piece / top outlet
The stove is prepared from the factory for top outlet.
The connecting piece is placed loosely in the top outlet of the stove.
The gasket for the connecting piece and the screws for fastening the
connecting piece are in the stove’s ash drawer.
Page 15
14
15
ASSEMBLY
Connecting
piece
Ceramic
asket
Fasten the connecting piece with screws from the ash drawer and
replace the top plate.
4 pcs. M5X10 mm screw
Connection piece / rear outlet
The stove is prepared from the factory for top outlet.
The connecting piece is placed loosely in the top outlet of the stove.
The gasket for the connecting piece and the screws for fastening the
connecting piece are in the stove’s ash drawer.
Lift the top plate and connecting piece off the stove.
Page 16
15
16
ASSEMBLY
Cut off the cover plate from the rear plate with cutting pliers at the
fastening points.
Fastening points
Lift the heat shield off the stove and cut the cover plate free using
cutting pliers at the fastening points and remove.
Page 17
16
17
ASSEMBLY
4 pcs. M5X10 mm screw
Fit the cover and tighten it. Replace the top plate.Remove the cover. This is to be used later as a seal and cover at the
top of the smoke outlet.
Fit the connecting piece with the four screws found in the stove’s ash
drawer. Hook the heat shield onto the stove.
Cover plate
Page 18
17
=
65-3 65-4
65-7 65-8
18
ASSEMBLY
The delivered gasket (4,5/7 m) should be cut in appropiate lengths
and sticked onto the sides of the stove as shown below.
Gasket
Fitting the natural stones
Some of the stoves are delivered with loose natural stone plates for
mounting on the sides of the stove.
It is a natural material, wherefore there might be differences in structure and form.
Each natural stone must be mounted with distance bushings and
screws which are already mounted in the stones.
Page 19
18
19
ASSEMBLY
Hook the natural stone sides onto the stove.
Remove the cover plate at the back of the stove or the cover plate at
the bottom of the wood compartment store, as shown on page 15.
Connect outside air to the connection piece underneath the combustion chamber.
External combustion
air via floor
External
combustion
air via wall
Fresh air intake
In a well-insulated house the air used for the combustion process
has to be replaced. This particularly applies to houses with mechanical ventilation. There are different ways of making sure that air is
exchanged. The most important thing is to ensure that there is a supply of air to the room where the wood stove is located. The external
wall vent must be located as close to the wood stove as possible, and
you must be able to close it when you are not using the stove.
National and local building regulations must be followed with regard
to connection of a fresh air intake.
Closed combustion system
You should use the closed combustion system for the wood-burning
stove if you live in a newly-built, airtight home. External combustion
air is connected through a ventilation pipe via the wall or floor.
It must be possible to shut off the ventilation pipe with a valve, when
the stove is not in use. Minimum Ø100 mm ventilation pipe, maximum length: 6 meters with a maximum of one bend.
If you want external combustion air via a wall, remove the cover plate
at the rear of the stove with a pair of cutting pliers. See the procedure
in this manual.
If the external combustion air is connected at the rear, the dismounted plate must be mounted on the hole for external air in the
bottom of the stove.
NOTE: if the stove has a fresh air connection or closed combustion,
the ventilation pipe must be open, when the stove is in use.
Page 20
19
65-9 & 65-1065-7 & 65-8
DATO:
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg
©
TG.NR:EMNE:
C:\Working Folder\Designs\Scan 68\90068058.idw
90068058
klargøring til vægbeslag
12-05-2015
hms
Scan 68
VÆGT:
AREAL:
N/A
N/A
20
ASSEMBLY / ACCESSORIES
Cover plate to
be removed
Do not remove the
radiation plate
The vent for adjustment of the convection air is placed at the back
of the high top
ClosedOpen
Cut off this plate from the heat shield in order to make place for the
heat accumulating stones
Open plinth
If you want open plinth, remove the wood compartment door and its
stop as well as the large cover plate at the back of the stove.
Heat-storage stone
Heat-storage stones are made from a special material with a high
heating capacity. The stones are heated up during the firing and
gives off the heat again after the firing, which means that the stove
stays warm for a longer time.
Firing with the vent open will give a quicker heating. Firing with the
vent closed will extend the heating time of the stove.
Fitting the natural stone top
You can buy a natural stone top as an accessory. Place the stone top
on the steel top plate
Page 21
0%-100%100%-0%
20
21
Baffle plates
The baffle plates are located in the upper part of the combustion
chamber. The plates hold back smoke, making sure it stays inside the
combustion chamber for a longer time before escaping through the
chimney. This reduces the flue gas temperature as the gases have
more time to dissipate heat to the stove. The baffle plates must be
removed for sweeping; see “Maintaining your wood-burning stove”.
Note that the baffle plates are made of porous, ceramic material, and
are liable to break easily. You should therefore handle them with care.
The baffle plates are subject to wear and tear and not covered by the
warranty.
Ash container
Open the door of the stove to access the ash container under the
combustion chamber.
The ash container must always be closed during operation.
The ash container must not be become too full and must therefore be
emptied at regular intervals.
Handle for riddling grate
The stove is equipped with a riddling grate that empties ash from the
combustion chamber down into the ash container when activated.
The riddling grate must remain half open while the wood stove is lit.
Primary air
Secondary air
Handle for riddling grate
Ash drawer
Adjustment of air supply,
primary and secondary damper
CB-technique
Baffle plates
INSTRUCTIONS FOR USE
IMPORTANT!
This screw (M5X6) must
be placed as shown in the
picture,to prevent secondary
air control closure beyond the
35mm open position .
A
CB technology (Clean Burn)
The stove is equipped with CB technology. In order to ensure optimal
combustion of gases released during the combustion process, air passes through a specially developed system of channels. The heated air
is conducted into the combustion chamber through the holes in the
rear lining of the combustion chamber and at the baffle plates. This
airflow is driven by the combustion rate and cannot be regulated.
NOTE: Wood must never be added above the CB rail.
Primary air
The primary air regulation mechanism is used for lighting the fire,
or to boost the burning process when you put wood on. The primary
air vent is used when you use hard wood fuel such as oak and beech.
The primary air vent can be closed if you use soft wood such as birch
or pine for fuel.
Settings for normal load: 0-30%
Settings for normal load: 50-70%
Secondary air
Secondary air is pre-heated and fed indirectly to the fire. At the same
time, the secondary airflow cleans the glass pane to prevent build-up
of soot. If you over-restrict the secondary airflow, soot can build up
on the glass pane. The secondary airflow determines the heat output
from your stove.
Page 22
21
22
INSTRUCTIONS FOR HEATING
INSTRUCTIONS FOR HEATING
Environmentally-friendly firing
Avoid turning down your stove to the point where no flames are
visible from the wood, as this leads to poor combustion and low efficiency. The gases released from the wood will not be burnt off due to
the low temperature in the combustion chamber. Some of the gases
will condense in the stove and flue system as soot, and this could lead
to your chimney catching fire at a later point. The residual smoke
which exits the chimney will pollute the surrounding area and cause
an unpleasant smell.
Lighting
We recommend the use of fire lighters, or similar products, which
are available from your Scan dealer. Using fire lighters helps light the
wood more quickly and keeps the combustion process clean.
Never use liquid lighting fuels!
“Top down” lighting
• 4 pieces of wood approx. 20-25 cm long with a weight of
approx. 0.4-0.5 kg per piece.
• 15-20 thin pieces of firewood of about 20 cm in length, with
a total weight of approx. 0.8 kg.
• 4 fire lighters in bag or block form
• Place the pieces of wood, firewood and fire lighters in the
combustion chamber.
• Set the primary and secondary airflow controls to maximum
for the entire lighting phase.
• "Top down" lighting is a more environmentally-friendly way
of lighting the fire and helps to keep the glass area as clean
as possible.
Continuous firing
It is important to obtain as high a temperature as possible in the
combustion chamber. This results in best possible use of the stove and
fuel, as well as achieving clean combustion. In this way you will avoid
build-up of soot on the combustion chamber lining and glass pane.
During operation, you should not see any smoke; just a movement in
the air that indicates combustion is in progress.
¬ After completing the lighting phase, you should have a good layer
of embers in the stove; you can then start operation of it proper. Add
two pieces of wood at a time: they should be about 0.6 to 0.8 kg in
weight and about 25 cm long.
NOTE: The wood must catch fire quickly; this is why we recommend
setting the primary airflow fully open. Operating the stove at too
low a temperature and with too little primary air can lead to gases
igniting, which can damage the stove.
¬ When adding wood, always open the glass door carefully to prevent
smoke escaping.
¬ Never add wood while the fire is burning nicely.
Firing in the spring or autumn
In the spring/autumn transition period, where there is less need for
heating, we recommend you light the stove “top down” once, perhaps
adding just two pieces of wood as above to ensure that the combustion chamber lining burns clean again.
The function of the chimney
The chimney is the wood-burning stove’s motor; its performance
determines how well your stove will work. The draught in the
chimney creates negative pressure in the wood-burning stove. The
negative pressure draws the smoke out of the stove and takes in air
through the combustion air damper to fuel the combustion process.
Combustion air is also used for the air wash system that keeps the
window clear of soot.
The draught in the chimney is created by the difference in temperature inside and outside the chimney. The higher temperature difference, the better draught. This is why it is important that the chimney
reaches operating temperature before you reduce the damper settings to restrict combustion in the stove (a brickwork chimney will
take longer to reach operating temperature than a steel chimney).
It is very important that the operating temperature is reached as
quickly as possible on days when the draught in the chimney is poor
due to unfavorable wind and weather conditions. You need to get a
few flames going as quickly as possible. Chop the wood extra thin; use
an extra fire lighter etc.
• After longer periods without use, you must check the
chimney flue for blockages.
• You can connect several units to the same chimney.
You should however first check the relevant regulations
in this respect.
Using your stove in various weather conditions
The way the wind affects the chimney can have a big impact on how
your stove reacts under various wind loads; you may need to adjust
the airflow to achieve good combustion. Fitting a damper in the flue
pipe may also help, as it will allow you to regulate the draught under
changing wind loads. The damper must not close more than 80% of
the surface.
Fog and mist can also have a big impact on chimney draught; you
may need to use other settings for the combustion air to achieve
good combustion.
General notes
note: Parts of the wood-burning stove, especially the outer surfaces,
become hot during use. Due care should be exercised.
¬ Never empty ashes into a flammable container. Ashes can contain
glowing embers long after you finish operating the stove. When the
stove is not in use you can close the dampers to avoid a draught
through the stove.
¬ If the stove has not been used for some time, you should check the
flue passageways for potential blockages before relighting.
Chimney fire
In the event of a chimney fire, keep the stove door, the ash container,
and all dampers on the stove closed. In an emergency, call the fire
service.
We recommend that you get a chimney sweep to check the chimney
before using the stove again.
Page 23
22
23
INSTRUCTIONS FOR HEATING
Fire starters
1.
2.
3.
4.
Handling fuel
Selecting wood/fuel
You can use any type of wood as fuel. However harder woods, such
as beech or ash, are generally better for heating, as they burn more
evenly and create less ash. Other woods, such as maple, birch and
spruce, are excellent alternatives.
Preparation
The best fuel is obtained where the tree has been felled and the wood
sawn and split before May 1st. Remember to cut the wood to match
the size of the combustion chamber. We recommend a diameter of
6-10 cm. The length should be about 6 cm shorter than that of the
combustion chamber to leave enough space for air to circulate. If the
diameter of the wood is greater than the above, it should be split
down its length. Wood that has been split dries faster.
Storing
You need to store the sawn and split wood in a dry place for 1-2 years
before it will be dry enough to burn. Wood dries faster if you stack
it in an airy place. Before using it, it is a good idea to store the wood
for a few days at room temperature. Remember that wood absorbs
moisture from the air during autumn and winter.
Moisture
To avoid problematic impact on the environment and to ensure optimum operating economy, the wood should be perfectly dry before it
can be used as fuel. Maximum wood moisture content should not
exceed 20%. A moisture content of 15-18% will deliver best efficiency.
An easy way of checking wood moisture content is to knock the ends
of the two pieces of wood together. If the wood is moist, the sound
will be slightly muffled.
If you use wood that is too damp, most of the heat it produces will
be used up in evaporating the water. The stove will accordingly not
increase in temperature, nor emit heat to the room as a result. This is
obviously poor economy, and it will cause soot build-up on the glass
pane, in the stove and in the chimney. Operation using moist wood
also pollutes the environment.
Understanding the terms used to designate
quantities of wood
Various terms are used to designate quantities of wood. Before you
buy wood, it makes sense to familiarize yourself with these terms.
There are various brochures, in public libraries for example, that cover
this topic.
Use of the following as fuel is illegal
Painted, pressure impregnated, or glued wood, or sea driftwood. Nor
should you ever burn chipboard, plastics, or treated paper. These
contain substances which are hazardous to human health, to the
environment, your stove, and your chimney. In short – make sure you
only use proper wood.
Calorific value of the wood
The various woods have different calorific values. In other words,
for certain species of wood, you will need to use a greater quantity
to achieve the same heating performance. This Instruction Manual
assumes that you will be using beech, which has a very high calorific
value and is also the easiest wood to buy. If you use oak or beech as
fuel, you need to bear in mind that these woods have a greater calorific value than, say, birch. To avoid any risk of damage to the stove, you
should therefore make sure you use less fuel in these cases.
Wood types Kg Dry wood/m3 Compared to beech
Hornbeam 640 110%
Beech/Oak 580 100%
Ash 570 98%
Maple 540 93%
Birch 510 88%
Pine 480 83%
Fir 390 67%
Poplar 380 65%
Calorific value of the wood
Page 24
23
24
MAINTENANCE
Maintainance
Apart from having the chimney swept, your wood-burning stove does
not require any regular maintenance. However, we do recommend
servicing at least once every two years.
• Only use original spare parts for maintenance and
repair of your stove.
• Make sure the stove is cold before starting maintenance
or repair work.
Painted surfaces
Clean your wood-burning stove by wiping it down with a dry, lint-free
cloth. If the paint finish gets damaged, you can purchase repair paint
in spray form from your Scan dealer. As slight differences in color
shade are possible, we recommend you spray a larger area to achieve
a natural blend. For best results, apply repair spray when the stove
is warm enough for you to just keep your hand on it, but no hotter.
Cleaning the glass
Our wood-burning stoves are designed to prevent serious soot buildup on the glass. The best way to achieve this is to make sure you have
a good supply of combustion air. It is also very important that the
wood is dry and the chimney correctly dimensioned.
Even if you operate the stove in accordance with our instructions, a
slight film of soot may still accumulate on the glass. You can easily
remove this film by wiping the glass down with a dry cloth and then
with a cloth dampened with glass cleaner.
• The glass cleaner is not to get into contact with the gaskets,
as this can discolor the glass permanently.
Combustion chamber lining
Slight cracks can appear in the combustion chamber lining due to
moisture or sudden heating/cooling. These cracks have no influence
on the output or lifetime of your stove. However, if the lining starts to
crumble and fall out, you must replace it. The combustion chamber
lining is not covered by the warranty.
Seals
All wood-burning stoves have seals made of ceramic material fitted
to the stove, the door and/or the glass. These seals are subject to wear
and tear and must be replaced when necessary.
Seals are not covered by the warranty.
Sweeping the chimney and cleaning stove
Follow national and local regulations for sweeping the chimney. We
recommend having the stove cleaned regularly by a chimney sweep.
Before cleaning the stove and sweeping the flue pipe and chimney,
we recommend removing the baffle plates.
Checking the stove
Scan A/S recommends that you check your stove thoroughly after
sweeping/cleaning. Check all visible surfaces for cracks. Check that
all joints are tight and that the gaskets are correctly seated. Worn or
deformed gaskets should be replaced.
Servicing
We recommend that the stove is thoroughly serviced at least once
every two years by a qualified fitter. The service should include the
following:
• Lubricate hinges using copper grease.
• Check the gaskets. Replace any that are broken or have gone soft.
• Check the combustion chamber bottom and riddling grate.
• Check heat-insulating materials.
Page 25
A
24
65-2, 65-4, 65-6, 65-8 & 65-10 65-1, 65-3, 65-5, 65-7 & 65-9
25
MAINTENANCE
Upper baffle
plate
Lower baffle
plate
(without side windows)(with side windows)
Upper baffle plate
Holder for upper
baffle plate
Service
Baffle plates and combustion chamber lining
Be very careful when removing the baffle plates from the stove.
Lift up the lower baffle plate, remove the pins and take out the baffle
plate.
Lift the upper baffle plate to the back of the combustion chamber.
Remove pins. Pull the plate free from the baffle plate holder and
remove it.
Lift the combustion chamber lining’s sides, remove them from the
rear cover and take them out.
Note that the combustion chamber lining’s sides support the rear
cover so this could fall when the sides are removed.
Remove the rear cover
Page 26
25
26
TROUBLESHOOTING
Warranty
All wood-fired Scan products are made of high-quality materials and
subject to strict quality controls before leaving the factory. We give a
warranty of 5 years on manufacturing errors or defects.
You must quote your stove‘s product registration number when you
contact us or your authorized Scan dealer with a warranty claim.
The warranty covers all parts which in the opinion of Scan A/S require
repair or replacement due to manufacturing or construction error
The warranty applies to the original purchaser of the product only,
and is not transferable (except on prior sale).
The warranty covers only damage caused by manufacturing or construction errors.
The following parts are not covered by
the warranty
• Wear and tear parts, such as the combustion chamber liners,
baffle plates, riddling grate, glass, and seals (except for defects
which were present on delivery).
• Defects caused by external chemical and physical influences
during transportation, storage and assembly, or at a later time.
• Soot build-up caused by poor chimney draught, damp wood,
or improper use.
• Costs of additional heating in connection with a repair.
• Transport costs.
• Costs for setting up, removing the wood stove.
This warranty is void
• In case of incorrect installation (the installer is responsible for
observing and complying with legal requirements and local
bylaws, along with this Instructions manual for the wood burning stove and accessories).
• In case of improper use, and/or use of prohibited fuels,
non-original spares (see this instructions manual).
• If the product registration number of the stove has been
removed or damaged.
• In case of repairs that do not comply with our instructions
or instructions by an authorized Scan dealer.
• In case of any manipulation of the original state of this
Scan product or its accessories.
• This warranty is only valid in the country to which this
Scan product was originally supplied.
Always use original replacement parts, or parts recommended by the
manufacturer.
Smoke escaping
• Damp wood
• Chimney not drawing properly
• Chimney is not properly dimensioned for the stove
• Check if the smoke gas pipe/chimney are blocked
• Is the chimney the right height for its surroundings?
• At rear outlet, check that the flue pipe does not obstruct
the chimney draught
• Vacuum in room
• The door is opened before the embers have burned
down sufficiently
Wood burning too quickly
• The air valves are set incorrectly
• The baffle plates is incorrectly mounted or missing
• Inferior firewood (waste wood, pallets etc.)
• Chimney too large
Soot build-up on glass
• Incorrect secondary airflow setting
• Excessive primary air
• Damp wood
• Wood pieces too large on lighting
• Inferior firewood (waste wood, pallets etc.)
• Chimney not drawing sufficiently
• Vacuum in room
Excessive soot build-up in chimney
• Poor burning (more air required)
• Damp wood
The surface of the stove is turning grey
• Overheating (see instructions for heating)
Poor heating performance of stove
• Damp wood
• Not enough wood
• Inferior wood quality with low fuel value
• Baffle plates are not fitted correctly
Odour coming from stove
• The lacquer on the stove hardens when you use the stove for the
first time; this can cause an odour. Open a window or a door for
ventilation, and make sure the stove is heated up sufficiently to
avoid odours later.
• When heating up and cooling down, the stove may make some
clicking noises. These are due to the huge temperature differences
to which the material is exposed and do not indicate any product
defects.
Page 27
26
27
Own comments
Page 28
28
01.01.2018
28
Version:
UK 90065500
Scan A/S-DK-5492 Vissenbjerg
Loading...