MODEL GC-STC-V
OPERATOR’S MANUAL
OPERATOR’S MANUALOPERATOR’S MANUAL
OPERATOR’S MANUALOPERATOR’S MANUAL
THIS MANUAL CONT AINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMATION FOR YOUR SCAG ACCESSOR Y . READING THIS MANUAL WILL PROVIDE YOU
WITH MAINTENANCE AND ADJUSTMENT
PROCEDURES TO KEEP YOUR ACCESSORY
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MACHINE, PLEASE READ ALL THE INFORMATION ENCLOSED.
PART NUMBER 03228
WARNING
FAILURE TO FOLLOW SAFE OPERATING PRACTICES
MAY RESULT IN SERIOUS INJURY.
* Keep all safety shields in place.
* Before performing any maintenance or service, stop the machine and
remove the spark plug wire.
* If a mechanism becomes clogged, stop the engine before cleaning.
* Keep hands, feet and clothing away from power-driven parts.
* Read this manual completely as well as the Operator's Manual that came
with your mower .
* Keep others off the mower (only one person at a time).
REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!
Hazard control and accident prevention are dependent upon the awareness,
concern, prudence, and proper training of the personnel involved in the
operation, transport, maintenance, and storage of the equipment.
This manual covers the operating instructions
and illustrated parts list for:
GC-STC-V with a serial number of E1800001 to E1899999
1.1 INTRODUCTION
WARNINGWARNING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
DANGER
This manual has been prepared to provide the
information you need to correctly assemble, operate,
and maintain this grass catcher. Read it carefully and
keep it for future reference.
THE REPLACEMENT OF ANY PART ON THIS
PRODUCT BY OTHER THAN THE
MANUFACTURER'S AUTHORIZED
REPLACEMENT PART MAY ADVERSELY
AFFECT THE PERFORMANCE, DURABILITY
OR SAFETY OF THIS PRODUCT.
USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.
If additional information or service is needed that is
not outlined in this manual, please contact your Scag
Power Equipment dealer. Scag dealers are trained in
the latest service methods and carry a full line of Scag
replacement parts.
When ordering parts, always provide the complete
model number and serial number of your catcher.
1. Read this operator's manual and the
operator's manual that is supplied with the
machine this attachment is used on.
A replacement manual is available from your
authorized Scag Service Dealer or by contacting:
Scag Power Equipment, Service Department at P.O.
Box 152, Mayville, WI 53050. You may also contact
us through our website at www.scag.com. The
manual for this grass catcher can be downloaded by
using the model and serial number or use the contact
form to make your request. Please indicate the
complete model and serial number of your Scag
product when requesting replacement manuals.
2. Before removing the grass bags, disengage the
mower, stop the engine and wait for all
movement to stop.
All information provided in this manual is based upon
information available at the time of printing. Scag
Power Equipment reserves the right to make changes
at any time without notice or obligation.
1.2 DIRECTION REFERENCE
The "Right" and "Left", "Front" and "Rear" of the
machine are referenced from the normal operating
position.
2.1 SAFETY AND OPERATING
INSTRUCTIONS
-NOTETo avoid personal injury, it is imperative that all
safety instructions be observed.
3. ALWAYS turn the engine OFF, remove the key
and wait for all movement to stop before
servicing or cleaning the mower or the grass
catcher.
DANGER
ROTATING BLOWER
BLADES
STOP ENGINE BEFORE
ENTERING CHUTE
CONTACT CAN INJURE
4. Do not modify or alter any component of the
grass catcher attachment or mower.
5. Do not allow any passengers to ride on the grass
catcher attachment or on the mower.
1
3.1 ASSEMBLY INSTRUCTIONS FOR 48"
WARNING
AND 52" CUTTER DECK
-NOTEUse the illustrated parts list as a part number
reference when following the assembly
instructions.
1. Remove all packaging materials. Lay out the
mounting hardware and the catcher assembly
parts for easy access. Prepare the work area
making sure that it is a clean, safe environment.
4. Install the grass catcher pulley onto the spindle
assembly. Apply loctite to both pulley setscrews
and tighten. See Figure 3-1.
5. Remove the "Custom-Cut" and "Turbo" baffles
from the cutter deck. Using the original
hardware, install the new "Front" and "Turbo"
baffles. See Figure 3-2.
Front Baffle
48V - 424401
52V - 424402
WARNING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
2. Remove the discharge chute from the cutter
deck. See Figure 3-1.
-NOTEDo not discard the discharge chute or
mounting hardware. The discharge chute
MUST be reinstalled any time the grass
catcher has been removed from the machine.
3. Remove the right side belt cover to gain access to
the spindle assembly. Remove the front u-nut
from the cutter deck bracket. See Figure 3-1.
-NOTERetain the original belt cover. This cover
MUST be reinstalled any time the
complete catcher system is removed.
INSTALL PULLEY
REMOVE DISCHARGE
CHUTE AND
HARDWARE
ON RH SPINDLE SHAFT ON TOP OF EXISTING
SPINDLE DRIVE
PULLEY
Turbo Baffle
48V - 424210
52V - 424211
UNDER SIDE OF
VELOCITY-PLUS
CUTTER DECK SHOWN
FIGURE 3-2
-NOTEDo not discard the original "Custom-Cut"
or "Turbo" baffles. These baffles may be
reinstalled any time the grass catcher has been
removed from the machine.
6. Install the blower mounting bracket to the deck
using carriage bolts (p/n 04003-11), lockwashers,
and nuts. Do not fully tighten the hardware at
this time. See Figure 3-3.
FLATWASHER
ELASTIC STOP
NUT
REMOVE U-NUT
FIGURE 3-1
REMOVE EXISTING
RT. SIDE BELT
COVER
RIGHT SIDE OF
CUTTER DECK SHOWN
(Note: Some parts not shown for viewing purposes.)
Figure 1- GC-STC-V install art
CARRIAGE BOLT
FIGURE 3-3
2
7. Install the blower assembly to the mounting
bracket and secure with the mounting pin.
See Figure 3-4.
8. Align the blower assembly with the discharge
opening of the cutter deck. Tighten the
hardware for the mounting bracket. See Figure
3-4.
12. Install the LH & RH hopper mounting brackets to
the outside of the frame on the rear of the machine
and secure using six (6) 3/8-16 x 1" hex head
bolts, and six (6) 3/8-16 elastic stop nuts. See
Figure 3-6. Do Not install mounting hardware in
the rear holes provided in the RH hopper mounting
bracket at this time.
LH
Hopper
Mounting
Bracket
9. Install the quick pin through the rear hole in the
discharge chute mounting bracket. See Figure
3-4.
MOUNTING PIN
TIGHTEN MOUNTING
BRACKET HARDWARE
2006 GC-STC-V install art 3
BLOWER
ASSEMBLY
QUICK
PIN
HAIR
MOUNTING
PIN
BRACKET
RIGHT SIDE OF
CUTTER DECK SHOWN
(Note: Some parts not shown for viewing purposes.)
FIGURE 3-4
10. Install the belt to the spindle pulley. When
replacing the belt, see Figure 3-5 below.
BACK SIDE
IDLER PULLEY
BLOWER
PULLEY
RH
Hopper
Mounting
Bracket
Rear Frame
3/8-16 x 1”
04001-32
3/8-16
Elastic Stop Nut
04021-09
Figure 4 A 2008 GC-STT Install Art
FIGURE 3-6
13. Remove the upper hex head bolt and serrated
flange nut securing the support bracket to the
frame of the machine. Retain the serrated flange
nut for re-use. Install the muffler guard as shown
and assemble to the frame of the machine by
installing two (2) 3/8-16 x 1-1/4" hex head bolts
through the rear holes in the RH hopper mounting
bracket and secure with two (2) 3/8-16 elastic
stop nuts provided. See Figure 3-7. Install the
front mounting tab of the muffler guard between
the support bracket and the frame of the machine.
Secure with the 3/8-16 x 1-1/2" hex head bolt
supplied with this catcher and the serrated flange
nut removed previously.
3/8-16
Elastic Stop Nut
04021-09
FRONT SIDE
IDLER PULLEY
SPINDLE
PULLEY
FIGURE 3-5
11. Install the new belt covers and secure. See
items number 1 and number 21 on page 10 of the
Blower Mounting Components section in this
manual for proper installation.
3/8-16 x 1-1/4
04001-32
Muffler Guard
3/8-16 x 1-1/2
04001-20
Support
Bracket
Existing
Nut
FIGURE 3-7
3
14. Attach the hood assembly to the machine by
installing the mounting post into the hopper
mounting brackets. Secure with the ring pins and
tighten the locking bolts. See Figure 3-8.
Locking
Bolts
Ring Pins
Locking
Bolts
Ring Pins
FIGURE 3-8
15. Install the hose from the blower assembly adapter
to the hopper hood and secure using the 6-1/2"
clamps.
16. Install the bag assemblies.
17. Using the weight support bar as a guide, identify
the four corresponding mounting holes, and the
existing hardware that will need to be removed in
order to secure the weight support bar to the
front of the machine as shown. See Figure 3-9.
18. Install one 7/16-14 x 1-3/4" hex head bolt into
each of the four mounting holes in the weight
support bar, and through the matching holes in
the caster support weldment. Secure this
assembly to the front of the machine using the
7/16- .5" x 1-1/4" x .083" flatwashers, and the
7/16-14 elastic stop nuts. Torque hardware to
59 ft. lbs. See Figure 3-9.
19. Operate and test.
FIGURE 3-9
4
WARNINGWARNING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED
5
4.1 GRASS CATCHER REMOVAL
INSTRUCTIONS
1. Prepare the machine so there is easy and safe
access to the work area. Remove the key and
maintain all safety related work procedures.
Always wear eye and hand protection.
2. Remove the bag assemblies from the grass
catcher.
3. Remove the rubber strap holding the adapter to
the blower assembly and the large quick pin
securing the blower to the discharge mounting
bracket. See Figure 4-1.
Loosen
Locking
Bolts
Remove Pins
Loosen
Locking
Bolts
Remove Pins
4. Remove the belt, pin, hair pin and large quick pin
securing the blower assembly to the cutter deck
and remove the blower assembly. See Figure
4-1.
BLOWER
ASSEMBLY
MOUNTING
BRACKET
2006 GC-STC-V removal art 1
ADAPTER
QUICK PIN
PIN & HAIR PIN
RIGHT SIDE OF
CUTTER DECK SHOWN
(Note: Some parts not shown for viewing purposes.)
FIGURE 4-1
FIGURE 4-2
6. With help from an assistant, remove the hood
assembly.
7. Re-install the side discharge chute to the opening
on the cutter deck. Replace the two (2) outside
mounting bolts on the discharge chute with the
clevis pins (p/n 04064-15) and rue cotter pins
(p/n 04069-03). See Figure 4-3.
8. Re-install the cutter deck belt cover.
DISCHARGE
CHUTE
5. Loosen the locking bolts and remove the two (2)
pins holding the hood assembly to the mounting
posts on the rear of the machine. See Figure
4-2.
CLEVIS PIN
P/N 04064-1
CLEVIS PIN
P/N 04064-15
GC-STC-V removal art 3
RUE COTTER PIN
P/N 04069-03
FIGURE 4-3
5
MAINTENANCE
5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS
HOURS
Break-In 8 20 40 100 200 500 Procedure Comments
(First 10)
X Check all hardware for tightness
X Inspect hose and adapter
X Check belt for proper alignment
X Inspect fabric bags
X *Check screen in hopper Remove debris from screen
X Inspect hose and adapter
X Inspect fabric bags
X Check condition of blower
X *Apply grease to blower bearings See figure below
X Check belt for proper alignment
* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.
GREASE FITTING
ON BEARING HOUSING
GREASE FITTING
ON BEARING HOUSING
BEHIND PULLEY
6
NOTES
7
39
DANGER
DANGER
GC-STC-V 48" & 52" BLOWER HOUSING ASSEMBLY
9
10
8
48
14
50
4
1
2
11
9
11
12
27
44
10
7
47
10
43
42
41
40
34
3
17
26
IN
S
T
A
WA
O
L
P
L
RE
E
B
R
AD
RN
E
A
O
L
T
P
T
E
I
N
R
C
ING
A
G
T
O
OR
M
V
'
S
E
A
M
R
C
AN
B
H
UA
IN
E
L
F
E
O
R
E
28
35
41
17
27
38
5
46
R
D
O
T
A
A
N
T
S
IN
t
o
G
p
G
e
n
E
B
g
i
n
L
R
D
e
U
O
A
D
b
N
I
e
N
S
D
L
f
O
C
o
E
E
r
H
T
S
e
A
S
O
S
c
R
G
P
l
e
G
E
A
R
R
NGE
R
E
W
O
L
B
DA
G
N
I
T
A
T
O
R
S
E
D
A
L
B
E
R
O
F
E
B
E
N
I
G
N
E
P
E
T
O
T
U
S
H
C
G
N
I
R
E
T
N
E
E
R
U
J
N
I
N
A
C
T
C
A
T
N
O
C
R
E
R
W
O
L
B
S
G
E
E
N
R
I
D
T
O
A
A
F
L
T
E
E
B
O
B
T
R
U
E
H
IN
E
C
G
DANGE
R
G
N
U
E
N
J
I
N
P
R
I
E
O
N
T
T
A
S
N
C
E
T
C
A
T
N
O
C
a
E
R
n
A
N
i
A
G
S
n
T
S
g
U
D
E
A
C
o
M
R
r
B
A
r
D
O
T
e
L
C
W
m
I
S
H
O
E
o
E
I
v
R
N
W
R
i
S
n
O
g
T
E
A
R
L
R
L
E
D
29
18
25
49
14
15
16
19
20
24
14
11
12
13
14
11
14
15
17
21
22
23
24
14
6
33
37
31
32
31
30
45
47
2005 GC V+ Blower Assembly
35
34
45
36
8
GC-STC-V 48" & 52" BLOWER HOUSING ASSEMBLY
Ref. Part
No. Number Description
1 04067-07 Pin, Ring 2-1/4" Long
2 481547 Lanyard, Deck Height Pin
3 04019-02 Nut, Serr. Flange 1/4-20
4 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4"
5 483392 Decal, Blower
6 483393 Decal, Rotating Blower
7 481428 Grip, Blower Lever
8 483223 Cap, Square
9 04024-02 Nut, Push On 3/8 Thread
10 04021-05 Lock Nut, 3/8-16
11 04041-07 Flatwasher, 3/8-.391 x .938 x .105
12 43277 Spacer
13 483209 Pulley, Idler 4" Dia.
14 04021-09 Nut, Elastic Stop 3/8-16
15 04030-04 Lockwasher, 3/8-16
16 424361 Plate, Catcher Mounting
17 04003-05 Bolt, Carr. 3/8-16 x 1-1/2"
18 04001-54 Bolt, Hex Head 3/8-16 x 3" - 52"
19 04001-81 Bolt, Hex Head 3/8-16 x 3-1/2"
20 04001-21 Bolt, Hex Head 3/8-16 x 1-3/4"
21 461928 Idler Arm Assembly
22 482379 Belt, GC-STC
23 483189 Pulley, 3-1/2" O.D., GC-STC
24 04043-04 Washer, 3/8 Hardened
25 43575 Pivot, Idler
26 483402 Decal, Belt Cover
Ref. Part
No. Number Description
27 04019-04 Nut, Serr. Flange 3/8-16
28 04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Gr. 8
29 483391 Decal, Danger
30 461931 Blower Housing Weldment
31 04003-12 Bolt, Carr. 5/16-18 x 3/4" Gr. 5
32 04063-06 Key, 1/4 x 1/4 x 1-1/2"
33 461796 Fan Weldment
34 483034 Bearing Assembly
35 04021-10 Nut, Elastic Stop 5/16-18
36 461930 Blower Housing Assembly, GC-STT
37 421319 Cover, Blower Housing
38 48136-02 Clamp, 8-5/8" Max Dia.
39 48135-09 Hose, 8.00" Dia. x 53" Long
40 482298 Pulley, 4-3/4" O.D. - 1" Bore
41 04012-04 Set Screw, 5/16-18 x 3/8"
42 461932 Frame, Blower Mount
43 481522 Spring, Main Drive
44 43212 Spacer
45 04019-03 Nut, Serr. Flange 5/16-18
46 461723 Adapter w/Strap
47 451821 Receiver Weldment, Mounting Post
48 04062-04 Hair Pin Cotter, .177 x 3-1/4"
49 424367 Dust Shield
50 04066-04 Quick Pin, 5/16" Dia.
9
GC-STC-V 48" & 52" BLOWER MOUNTING COMPONENTS
UNDER SIDE OF
VELOCITY-PLUS
CUTTER DECK SHOWN
16
10
16
10
2
4
1
3
14
22
15
16
20
18
17
12
5
6
13
15
11
26
27
6
7
8
9
21
25
28
25
25
24
23
24
26
23
19
RIGHT SIDE OF
CUTTER DECK SHOWN
2006 GC-STC-V BMC
10
GC-STC-V 48" & 52" BLOWER MOUNTING COMPONENTS
Ref. Part
No. Number Description
1 483224 Belt Cover, GC-STC
2 04029-04 Wingnut, Plastic 3/8" Small
3 483223 Cap, Square Vinyl
4 04021-08 Nut, Elastic Stop 1/4-20
5 461723 Adapter, Blower GC-STC, includes item #7
6 04040-14 Flatwasher, 1/4-.312 x .750 x .065
7 48137-04 Rubber Strap 7-3/4"
8 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4"
9 481625-01 Knob W/Stud, 3/8-16 x 1-1/4"
10 04064-15 Clevis Pin, 5/16 x 1-1/2"
11 04069-03 Pin, Rue Cotter 5/16 Dia.
12 04067-07 Pin, Ring 1/2 x 2-1/4"
13 481547 Lanyard
14 482587 Pulley, 4.0" Dia. 1.125 Bore
15 04012-04 Setscrew, 5/16-18 x 3/8"
16 04021-09 Nut, Elastic Stop 3/8-16
17 04030-04 Lockwasher, 3/8"
18 04041-07 Flatwasher, 3/8-.391 x .938 x .105
19 04003-11 Bolt, Carr. 3/8-16 x 1-1/4" Grade 5
20 461894 Mounting Post Weldment, Blower
21 424326 Belt Cover, GC-STC-48V
424327 Belt Cover, GC-STC-52V
22 04110-03 U-Nut
23 04003-23 Bolt, Carriage 3/8-16 x 1"
24 04001-09 Bolt, Hex Head 5/16-18 x 1"
25 04040-15 Flatwasher, 5/16-.375 x .875 x .083
26 04021-10 Nut, Elastic Stop 5/16-18
27 424401 Baffle, Front 48" Deck
424402 Baffle, Front 52" Deck
28 424210 Baffle, Turbo 48" Deck
424211 Baffle, Turbo 52" Deck
11
GC-STC BUCKET SUPPORT COMPONENTS (UPPER)
3
36
37
35
1
2
4
32
31
11
38
17
3
5
24
9
35
31
4
33
33
22
21
16
23
5
9
18
5
16
25
9
34
19
13
16
5
4
6
5
9
8
23
16
21
13
20
16
14
11
5
9
18
16
15
30
32
29
28
27
26
12
40
7
39
10
12
GC-STC BUCKET SUPPORT COMPONENTS (UPPER)
Ref. Part
No. Number Description
1 423302 Screen, Catcher Hood
2 04090-02 Pop Rivet, 3/16 x .652
3 04041-19 Flatwasher, 3/16-.196 x .469 x .048
4 04001-32 Bolt, Hex Head 3/8-16 x 1-1/4"
5 04041-01 Flatwasher, 3/8-.391 x .938 x .105
6 461408 Hood Assembly, GC-STT (includes items 1, 2 & 3 and items 2 & 15 on page 15)
7 04001-117 Bolt, Hex Head 7/16-14 x 1-3/4"
8 423258 Hinge, Upper LH
9 04021-09 Nut, Elastic Stop 3/8-16
10 04040-11 Flatwasher, 7/16-.500 x 1-1/4"
11 04001-46 Bolt, Hex Head 3/8-16 x 2-1/4"
12 04021-11 Nut, Elastic Stop 7/16-14
13 04001-20 Bolt, Hex Head 3/8-16 x 1-1/2"
14 04001-135 Bolt, Hex Head 3/8-16 x 1-3/4" Grade 8
15 451674 Support Weldment, Bag Frame
16 04019-04 Nut, Serrated Flange 3/8-16
17 04090-03 Pop Rivet, 3/16 x .402
18 43546 Bushing, Hopper Pivot
19 482304 Spring, Hood Hinge
20 423436 Hinge, Lower LH
21 43212 Spacer
22 04021-05 Locknut, 3/8-16
23 43277 Spacer
24 423259 Hinge, Upper RH
25 423261 Hinge, Lower RH
26 48135-13 Hose, 8" Dia. x 56"
27 48136-02 Clamp, 8-5/8" Max Dia.
28 482422 Tube, Filler
29 482421 Elbow
30 04001-10 Bolt, Hex Head 5/16-18 x 1-1/4"
31 04021-10 Nut, Elastic Stop 5/16-18
32 04040-15 Flatwasher, 5/16-.375 x .875 x .083
33 04041-11 Flatwasher, 3/8- .406 x 1-1/2" x .179
34 04030-04 Lockwasher, 3/8" Spring
35 482409 Latch
36 04010-25 Screw, #10-32 x 3/4"
37 04021-01 Nut, Elastic Stop #10-32
38 04001-08 Bolt, Hex Head 5/16-18 x 3/4"
39 451517 Support Weldment, Weights
40 461097 Weight Assembly
13
GC-STC BUCKET SUPPORT COMPONENTS (LOWER)
1
2
24
22
23
21
20
19
17
16
18
15
"A"
13
11
4
TO "A"
3
4
4
5
4
8
5
6
7
14
26
25
6
12
3
6
9
6
4
8
7
FRAME
5
10
9
10A
STC 2008 BSC
14
GC-STC BUCKET SUPPORT COMPONENTS (LOWER)
Ref. Part
No. Number Description
1 04090-02 Pop Rivet, 3/16 x .652
2 482321 Seal, Hood
3 423262 Tube, Upright
4 04041-07 Flatwasher, 3/8-.391 x .938 x .105
5 04021-09 Nut, Elastic Stop 3/8-16
6 04020-04 Nut, 3/8-16
7 04021-05 Hex Lock Nut, 3/8-16
8 04067-07 Pin, Ring 1/2 x 2-1/4"
9 04001-19 Bolt, Hex Head 3/8-16 x 1"
10 461995 Mounting Bracket Weldment RH
10A 461994 Mounting Bracket Weldment LH
11 04021-02 Lock Nut, 1/4-20 Center
12 04001-46 Bolt, Hex Head 3/8-16 x 2-1/4"
13 04001-31 Bolt, Hex Head 3/8-16 x 2-1/2"
14 482569 Bag Assembly, GC-STT
15 423312 Retainer, Seal
16 451674 Support, Bag Frame
17 04003-02 Bolt, Carr. 1/4-20 x 3/4"
18 04001-08 Bolt, Hex Head 5/16-18 x 3/4"
19 423198 Mount, Bag Frame Tube
20 04003-12 Bolt, Carr. 5/16-18 x 3/4"
21 423197 Tube, Bag Suppor t
22 04019-03 Nut, Serr. Flange 5/16-18
23 04040-15 Flatwasher, 5/16-.375 x .875 x .083
24 04021-10 Nut, Elastic Stop 5/16-18
25 04001-32 Bolt, Hex Head 3/8-16 x 1-1/4"
26 451969 Muffler Guard
15
483402
GC-STC-V DECALS
482275
MANUFACTURED UNDER ONE OR MORE
OF THE FOLLOWING PATENTS:
4,487,006 4,885,903 4,920,733 4,967,543
4,991,382 4,998,948 5,042,239 5,117,617
5,133,176 5,826,416 5,832,708 5,865,018
6,192,666 6,766,633 6,892,519 6,996,962
7,065,946
PATENTS PENDING
483044
481327
483391
483392
483392
483391
483393
16
483393
LIMITED WARRANTY- COMMERCIAL ACCESSORY
Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,
to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without
charge for parts and labor.
The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within
the warranty period. The expense of delivering the accessory to the dealer for warranty work and the expense of
returning it back to the owner after repair or replacement will be paid for by the owner. Scag’s responsibility in respect
to claims is limited to making the required repairs or replacements, and no claim of breach of warranty shall be cause
for cancellation or rescission of the contract of sale of any Scag machine. Proof of purchase will be required by the
dealer to substantiate any warranty claim. All warranty work must be performed by an Authorized Scag Service
Dealer.
This warranty is limited to 90 days from the date of original retail purchase for any Scag accessory that is used for
commercial purposes, or any other income-producing purpose including rental use.
The warranty for the blower assembly (excluding the belt) is limited to 1-year from the date of original retail
purchase. 90 Days for rental use.
This warranty does not cover any accessory that has been subject to misuse, neglect, negligence, or accident,
or that has been operated in any way contrary to the operating instructions as specified in the Operator's Manual.
The warranty does not apply to any damage to the accessory that is the result of improper maintenance, or to
any accessory or parts that have not been assembled or installed as specified in the Operator's Manual.
The warranty does not cover any accessory that has been altered or modified. In addition, the warranty does not
extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or
durability. This warranty does not cover engines and electric starters, which are warranted separately by their
manufacturer.
Scag Power Equipment reserves the right to change or improve the design of any accessory without assuming any
obligation to modify any accessory previously manufactured.
All other implied warranties are limited in duration to the 90 day warranty period. Accordingly, any such implied
warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety
after the expiration of the appropriate ninety day warranty period. Scag’s obligation under this warranty is strictly
and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone
to assume for them any other obligation. Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense
for gasoline, oil, expense of delivering the machine to an Authorized Scag Service Dealer and expense of returning
it back to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time
warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of
the mower, loss of time, or inconvenience. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
© 2007
SCAG POWER EQUIPMENT
DIVISION OF MET ALCRAFT OF MAYVILLE, INC.
WWW.SCAG.COM
PART NO. 03228
PRINTED 3-2007
PRINTED IN USA
Loading...