Scag 7630001 User Manual
MODEL TS
ACCESSORY FOR:
STT - ALL MODELS
STC - MODELS ABOVE SERIAL NUMBER 7630001
OPERATOR’S MANUAL
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMATION
FOR YOUR SCAG ACCESSOR Y. READING THIS
MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES
TO KEEP YOUR ACCESSORY PERFORMING
TO MAXIMUM EFFICIENCY. THE SPECIFIC
MODELS THAT THIS BOOK COVERS ARE CONTAINED ON THE INSIDE COVER. BEFORE
OPERATING YOUR MACHINE, PLEASE READ
ALL THE INFORMATION ENCLOSED.
© 2003
SCAG POWER EQUIPMENT
DIVISION OF MET ALCRAFT OF MA YVILLE, INC
WWW.SCAG.COM
P ART NO. 03142
PRINTED 8-2003
PRINTED IN USA
WARNING
FAILURE TO FOLLOW SAFE OPERATING PRACTICES
MAY RESULT IN SERIOUS INJURY.
* Keep all safety shields in place.
* Before performing any maintenance or service, stop the machine and
remove the spark plug wire.
* If a mechanism becomes clogged, stop the engine and wait for all moving
parts to come to a complete halt before cleaning.
* Keep hands, feet and clothing away from power-driven parts.
* Read this manual completely as well as the Operator's Manual that came
with your mower .
* Keep others off the tractor (only one person at a time).
REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!
Hazard control and accident prevention are dependent upon the awareness,
concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the equipment.
This manual covers the operating instructions
and illustrated parts list for:
TS with a part number of 9269
1.1 INTRODUCTION
2.1 SAFETY INFORMATION
This manual has been prepared to provide the
information you need to correctly assemble, operate,
and maintain this Tiger Striper. Read it carefully and
keep it for future reference.
The replacement of any part on this product by other
than the manufacturer's authorized replacement part
may adversely affect the performance, durability or
safety of this product.
USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.
If additional information or service is needed that is
not outlined in this manual, please contact your Scag
Power Equipment dealer. Scag dealers are trained in
the latest service methods and carry a full line of Scag
replacement parts.
When ordering parts, always provide the complete
model of this Tiger Striper.
All information provided in this manual is based upon
information available at the time of printing. Scag
Power Equipment reserves the right to make changes
at any time without notice or obligation.
1.2 DIRECTION REFERENCE
-NOTE-
To avoid personal injury, it is imperative that all
safety instructions be observed.
1. Read this operator's manual and the
operator's manual that is supplied with the
machine this attachment is used on.
A replacement manual is available from your
authorized Scag Service Dealer or by contacting:
Scag Power Equipment, Service Department at P.O.
Box 152, Mayville, WI 53050. You may also contact
us through our website at www.scag.com. Please
indicate the complete model number of your Scag
product when ordering a replacement manual.
2. Before removing the Tiger Striper, disengage the
mower, stop the engine and wait for all
movement to stop.
3. ALWAYS turn the engine OFF, remove the key
and wait for all movement to stop before
servicing, cleaning or removing the Tiger Striper.
4. Do not modify or alter any component of the
Tiger Striper attachment or mower.
5. Do not allow any passengers to ride on the
mower.
The "Right" and "Left", "Front" and "Rear" of the
machine are referenced from the normal operating
position.
2.2 OPERATING INSTRUCTIONS
To operate the Tiger Striper, you will need to lower
the roller to the operating position. The Tiger Striper
can be easily removed or locked in the transport
position whenever the machine is being transported
or when striping is not needed.
1. To unlock the Tiger Striper from the transport
position, lift up slightly on the handle and turn the
lock pin until the small roll pin lines up with the
slot. See Figure 2-1 on page 2.
1
Roll Pin
Lift Up on
Handle
Push and Turn Pin to line
up Roll Pin with Slot
to Unlock
FIGURE 2-1
3. Repeat this procedure on the opposite side.
3. Repeat on opposite side.
4 . Once the Tiger Striper is locked in the transport
position, remove the ring pins securing the Tiger
Striper to the mounting brackets. See Figure 2-3
The machine is now ready to operate.
2.3 REMOVING THE TIGER STRIPPER
The Tiger Striper can be easily removed whenever
the machine is being transported or when stripping is
not needed. To remove the Tiger Striper, follow the
instructions below.
1. Prepare the machine so there is easy and safe access
to the work area. Remove the key and maintain all
safety related work procedures. Always wear eye and
hand protection.
2. Lock the Tiger Striper up in the transport position by
lifting upward on the handle, push and turn the lock
pin 90 degrees. The small roll pin must be out of the
slot in the bracket to lock in the transport position.
See Figure 2-2.
Roll Pin
Remove Ring Pins
FIGURE 2-3
5. Slide the Tiger Striper off of the mounting
brackets.
6. To install the Tiger Striper, slide the assembly on
to the mounting brackets and reinstall the ring
pins. Once the Tiger Striper has been reinstalled,
follow Section 2.2 Operating Instructions for
proper operation.
3.1 ASSEMBLY INSTRUCTIONS - STT
-NOTE-
Use the illustrated parts list as a part
number reference when following the
assembly instructions.
FIGURE 2-2
Push and
Turn Pin to
Lock
1 . Remove all packaging materials. Lay out the
mounting hardware and the Tiger Striper assembly for
easy access.
2. Prepare the machine so there is easy and safe access
to the work area. Remove the key and maintain all
safety related work procedures. Always wear eye and
hand protection.
2
3. Attach the mounting brackets to the cross bar
between the wheel motor brackets using (4) ubolts and (8) serrated flange nuts. See Figure
3-1. Do not tighten the hardware.
5. Install the left and right hand Striper Stop
Brackets (p/n 423953 & p/n 423954) to the
frame and secure with (4) 3/8-16 x 1" bolts and
(4) elastic stop nuts. See Figure 3-2.
-Note-
If the Tiger Striper is installed on an STT with
a serial number below 7219999, part
number 423966 mounting spacer will need to
be installed between the mounting bracket
and cross bar. See Figure 3-1.
(4x) U-Bolts
Mounting
Bracket
(8x) Serrated Flange
Nuts
Mounting
Bracket
STT with a serial number of 7219999 or Below
(4x) U-Bolts
(4) 3/8-16 Elastic
Stop Nut
423953 L.H.
Stop Bracket
(4) 3/8-16 x 1" Bolt
423954 R.H.
Stop Bracket
FIGURE 3-2
6. Install the Tiger Striper roller assembly to the
mounting brackets and secure with the ring pins.
7. Once the Tiger Striper roller assembly is installed
and secure, tighten the mounting hardware on
both mounting brackets.
8. Follow Section 2.2 Operating Instruction for
proper operation.
Mounting
Spacer
Mounting
Bracket
Mounting
Spacer
Mounting
Bracket
(8x) Serrated Flange
Nuts
FIGURE 3-1
4. The edge of the mounting bracket should be
under the wheel motor mounting plate for proper
installation. See Figure 3-1.
3.2 ASSEMBLY INSTRUCTIONS - STC
-NOTE-
Use the illustrated parts list as a part
number reference when following the
assembly instructions.
1. Remove all packaging materials. Lay out the
mounting hardware and the Tiger Striper
assembly for easy access.
2. Prepare the machine so there is easy and safe
access to the work area. Remove the key and
maintain all safety related work procedures.
Always wear eye and hand protection.
3
Loading...