Page 1
Installation Instructions
P/N: 75-5036 / 75-5036D
VEHICLE APPLICATION
Year: 1999-06
Make: Chevy/ GMC/ Cadillac
Model: Silverado, Tahoe, Suburban,
Sierra, Yukon, Escalade - 1500, 2500
Engine: 4.8L, 5.3L, 6.0L
NOTE: Will fit 2007 Silverado Classic
NOTES
Kit may not fit with the following
Aftermarket Parts installed:
Body Lift or Lowering Kit
•
Custom Hood
•
Throttle Body Spacer/ Upgrade
•
1. With the ignition switched off and the
parking brake set, disconnect the negative
battery cable on the battery.
TOOLS REQUIRED
10mm Wrench & Socket
•
T-20 Security Torx Wrench (Supplied w/ Kit)
•
4mm Allen Wrench
•
5/16” Nut Driver or Flat Blade Screwdriver
•
Phillips Screwdriver, Pliers or Channel locks
•
CARB Status - Exempt
CARB EO #: D-590-5
Legal for use in CA or other states
adopting CA emissions standards
See Page 3 for more info.
2. If equipped: Loosen the retaining bolt
and pull up and out to remove the engine
cover from the vehicle.
Cleanable (KF-1035). If the enclosed filter is Red, it came pre-oiled
from the factory. When serviced, apply (87g) of S&B oil to the main
body of the filter and (17g) to the Power Stack (Top).
Disposable (KF-1035D). If the enclosed filter is White, it is a
disposable filter and should be discarded once it reaches capacity.
This filter (does not require oil). For more info on S&Bʼs disposable
filter, visit www.sbfilters.com.
Before You Start
S&B FILTER MAINTENANCE
Please read the entire product guide before proceeding.
•
Ensure all components listed on page 4 are present.
•
If you are missing any of the components, call our customer
•
support at (909) 947-0015.
Do not work on your vehicle while engine is hot.
•
Make sure the engine is turned off and the vehicle is in Park or
•
the Parking Brake is set.
3. Disconnect the electrical connection to
the MAF sensor at the OE air box.
4. Carefully pry the hose router clamp from
the OE air intake tube.
7. Loosen the hose clamp on the OE air
box and remove the MAF sensor. Note: The
direction of the air flow through the sensor.
5. Loosen the hose clamp at the throttle
body and at the MAF sensor
8. Remove the OE tray from the vehicle.
Four of these bolts (if long enough), can be
used to secure the S&B air box to the vehicle.
If too short, then use the supplied allen head
screws an SS washers.
6. Pull the OE air box towards the engine
and up to release it from the vehicle.
9. Attach the Filter Adapter (I) to the Air Box
(G), secure using the supplied 5/16” SS
Screws (H).
SEE EXPLODED VIEW ON PAGE 4
15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.com
1
Page 2
Installation Instructions (continued)
P/N: 75-5036 / 75-5036D
10. Place the air box assembly into the
vehicle, align the four holes with the OE
mounting locations and secure using either
the OE bolts or the supplied allen head
screws and SS washers.
13. Slide the Hump Adapter (L) over the
MAF sensorʼs plastic flange and secure using
a #60 Hose clamp (J).
11. Slide the Straight Adapter (F) over the
MAF sensorʼs metal flange, secure using a
#60 Hose clamp (J).
14. Slide the Throttle Body Adapter (O) over
the Intake Tube (M) along with the #72 Hose
Clamp (N), do not fully tighten at this time.
12. Connect the MAF sensor assembly to
the Filter Adapter (I) and secure using a #60
Hose clamp (J).
15. Place another #60 Hose clamp (J) on the Hump
Adapter (L) then insert the small end of the Intake Tube
(M) into the Hump Adapter. Then position the other end
of the tube over the throttle body and firmly secure the
#72 Hose Clamp (N), then secure the #60 Hose Clamp
(J) at the hump adapter.
16. Carefully place the S&B Air Filter (D)
into the Air Box (G), rotate the filter about a
1/4 turn for clearance and slide onto the
flange and secure the #80 Hose clamp (E).
19. Reconnect the MAF sensor electrical
connection.
17. Remove the protective covering from
the Clear Lid (C).
20. Re-Install the cover removed in
Step #2.
18. Place the Clear Lid (C) on the Air Box
(G) and secure using the 10/24 SS Screws
(A) and SS Washers (B).
21. Reconnect both batteries. Inspect your
installation, make sure the kit is properly
positioned and all fasteners are secure. Affix
the CARB sticker near the intake kit. The
installation is now complete.
SEE EXPLODED VIEW ON PAGE 4
15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.com
2
Page 3
EMISSIONS STANDARD
The California Air Resource Board (CARB) requires that an E.O. identification label be applied to the vehicle in order to pass a smog
check inspection when a Performance Intake Kit has been installed. You must place the E.O. label provided on or near the intake kit
after installation so that a smog check technician can easily verify the E.O. number. As of April 2009, S&B has never had a product
where CARB denied an exemption request; however, the exemption process with CARB can take as long as 18 months. Check the
status of the exemption process by looking up a specific part number at www.sbfilters.com. The CARB Exemption number and/or
status is listed under the Product Details section for each part number. If the status shows as “Pending,” CARB has yet to issue an
exemption. Products that have not been issued an EO number are street legal in most states, but may not be used on emission
controlled vehicles in the state of California and are for off road use only. If you purchased your kit from S&B Filters directly, we will
automatically mail you your Exemption Sticker when it is issued to us. If you purchased your kit from an authorized S&B Filters Dealer,
log onto our web site and register to receive your Exemption Sticker.
Installation Instructions (continued)
P/N: 75-5036 / 75-5036D
PRECISION II
FILTER CLEANING & OILING
Order online today at www.sbfilters.com or
through your local S&B distributor.
Part #: 88-0008
RELATED ITEMS FOR YOUR
PURCHASE
Replacement Air Filter (Oiled)
•
(S&B P/N: KF-1035)
Replacement Air Filter (Dry)
•
(S&B P/N: KF-1035D)
Air Filter Wrap (S&B P/N: WF-1023)
•
Installation Notes:
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
Performance Testing
Engage parking brake and start your engine. Listen for abnormal noises. If an air leak is detected, re-inspect hoses and connections as they may need to be repositioned and
•
tightened.
S&B FILTERS recommends that you keep your OE intake system in the event it is required in the future.
•
In order to maintain your warranty, all connections and components must be checked periodically for alignment and for proper tension on all connections. Failure to do so
•
may void your warranty.
Use only S&B FILTERS cleaning and oil products to service your filter. Using any other brand oil and or cleaners on your S&B air filter may void your warranty.
•
Warning!
If your vehicle has a Vehicle Emission Control Information decal affixed to the factory airbox, a new
replacement label must be obtained and installed in a readily visible position in the engine compartment in
order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check.
Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall
not be affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood
on a painted surface is recommended.
15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.com
SEE EXPLODED VIEW ON PAGE 4
3
Page 4
ITEM
QTY.
DESCRIPTION
P/NA4
S.S. Screw, 10-24 x 1/2”
AI1287-00
B4S.S. Sealing Washer, 10-24
AI1272-00
C1Clear Lid
AI1371-00
D1S&B Air Filter
KF-1035E1
Hose Clamp, #80
AG1010-00
F1Straight Adapter
AI1129-00
G1Air Box
AL1080B-00
H2S.S. Screw, 5/16-18 x 1.0”
AI1297-00
I1Air Box Adapter
AL1084A-00
J4Hose Clamp, #60
AG1008-00
K
4
Screw, Allen Head, M6-1.0x30mm
AI1366-00
L1Hump Adapter
AI1321-00
M1Intake Tube
AL1084-00
N1Hose Clamp, #72
AG1009-00
ITEM
QTY.
DESCRIPTION
P/N
O1Throttle Body Adapter
AI1097-00
P4S.S. Washer, 3/8” x 1.0”
AI1341-00
Q2Hose Clamp, #4
AG1021-00
R1Rubber Hose, 3/8” x 13” Long
AI1037-00
EXPLODED VIEW
P/N: 75-5036 / 75-5036D
15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.com
AM0129-00 Rev.G 10/01/13
4
Loading...