S&B 75-1511-1 User Manual

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Part # 75-1511-1
DODGE

RAM 5.2L & 5.9L

* Kit may not fit vehicles with body
lift installed.

QTY PARTS LIST QTY PARTS LIST (continued)

1 Intake Tube 2 Rivet Style Jack Nuts
1 Intake Box 4 #10 Sealing Washers
1 Intake Box Lid 4 SS Pan Head Screws
1 CARB Sticker 1 Air Filter
1 Throttle Body Gasket
1 “S” Bolt
2 #10-24 Pan Head Screws
2 #10 Flat Washers
2 1/4” - 20 Nylock Nuts
1 1/4” Fender Washer

1 1/2” x 26” L Hose

TOOLS REQUIRED

Flat Head Screw Driver
Phillips Head Screw Driver
Pliers
3/8” Socket or Wrench

1. With the ignition switched off, discon­nect the negative battery cable. Loose
the air cleaner hose clamp from the
throttle body.

2. Disconnect the crank case vent line
from the OEM air cleaner housing.

4. Install the supplied gasket to the throttle
body.

5. Thread the supplied “S” bolt into the
throttle body until tight, and back off
one full turn.

7) B) Repeat step for second nuts and
remove the #10-24 screws from the rivet
nuts. You will use these screws later to
install the intake box.

8. Install the intake box on to fenderwell
and secure using the supplied #10-24
screws and 1/4” washers.

3. Remove the air cleaner and intake tube
assembly by pulling up and towards
the center of the vehicle to detach the
tube from the inner fender well. Re­move the stock throttle body gasket as
well.

6.

Locate two (2) holes on passenger side
fender well.

7. A) Insert jack nuts into holes in fender
well and tighten #10-24 screws into
the jack nut while holding the jack nut
tight with pliers.

9. Insert the intake tube into air box first,
then rotate the intake tube over the “S”
bolt in the throttle body.

10. Adjust the air tube until it seats com-

pletely over the throttle body and rests on
the supplied gasket.

4/26/2007

(909) 947

-0015 PHONE • [phone] FAX

(OVER)

INSTALLATION INSTRUCTIONS (continued)

11. Install the 1/4” fender washer and nut
onto “S” bolt and tighten securely. Do

not over tighten the nut.

PERFORMANCE TESTING

∗

Engage parking brake and start
your engine. Listen for abnormal
noises. If an air leak is detected,
re-inspect hoses and connections
as they may need to be reposi­tioned and tightened.

∗ S&B FILTERS RECOMMENDS

12. Install crank case vent line from the
intake tube to the fitting on the valve
cover.

13. Slide the filter’s hose clamp over the
air tube first and then install the air filter
into the air box. Push the filter against
the inner wall of the air box and tighten
hose clamp securely.

THAT YOU KEEP YOUR OEM
INTAKE SYSTEM IN THE
EVENT IT IS REQURIED IN THE
FUTURE.

∗ In order to maintain your war-

ranty, all connections and com­ponents must be checked peri­odically for alignment and for
proper tension on all connec­tions. Failure to do so will void
your warranty.

∗ Use only S&B Filter cleaning and

oil products to service your filter.
Using any other brand oil and or
cleaners may void your warranty.

14. Install clear intake box lid using s upplie d
sealing washers and SS pan head screws.

15. Ensure all connections are tight and posi­tioned properly before starting vehicle.
Reconnect negative battery terminal.

Adhere the CARB sticker in plain sight
under the hood.

S&B’S Precision Cleaning & Oiling
Kit allows vehicle owners to properly
maintain their high performance air
filters by precisely applying the cor­rect amount of oil. The clearly
marked bottle and easy-to-use appli-

Part No. 88-0005

Order online today at www.sbfilters.com
or though your local S&B Distributor

4/26/2007

[phone] Phone • [phone] Fax

www.sbfilters.net