Connection
• The track accessories are provided with earth connection points on both sides.
• When offering the accessory to the track, verify which tab needs to be
removed. (See left hand diagram).
• To remove the tab, grasp firmly with a pair of pliers and lever back.
The tab should snap cleanly off. (See right hand diagram).
• Locate the accessory in the track and push home.
Remaining Earth tab needs
to be inserted into Earth
conductor to ensure Earth
continuity.
End view of track
Remove One
or Other Tab
Marked in Grey
Wiring
• Undo the screw and remove the cover from the live end. Push out the desired cable access point.
• Indentify the correct cable from the supply and pull through.
• Connect the supply wires to the terminal block, opposite the corresponding wires from the fitting.
The central connector can also be wired in this way.
• Refit the cover onto the live end taking care not to trap the cable.
Supply
N
L
N
Check that ......
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.
L
Instruction leaflet
Cody track
Earth
Conductor
79219, 79303
Fitting Units
• Locate the product in the track with the connections in the slot.
• Slide the tab down, and rotate the product 90 degrees to engage the connections in the track.
• Allow the tab to slide back up and ensure that it is located correctly in the track slot.
• Replace fuse or circuit breaker and switch on. Your light is now ready for use.
Care and Safety
• We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
• Always disconnect the product from mains at least 10 minutes allowing to cool down before any maintenance or adjustment.
WWW.saxbylighting.com
Iss .1 9/11/2018
Saxby lighting. BH23 3PE
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Warining
Please read these instructions carefully before commencing
any work.
If replacing an existing fitting, make a careful note
of the connections.
Products
Install the product on the track:
150mm175mm
1 2
90mm
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
Check the pack and make sure you have all of the parts
listed.
To prevent electrocution switch off at mains supply before
installing or maintaining this fitting.
Ensure other persons cannot restore the electrical supply
without your knowledge.
If replacing an existing fitting, make a careful note of the
connections.
Technical data
Supply
Voltage:
Bulb Type:
240 V~, 50 Hz
Max. 38W LED COB 4000K
Conformity with all relevant EC Directive requirements.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist.Check with your Local Authority or
local store for recycling advice.
This light fitting should be connected to a fused circuit.
The light source of this luminaire is not replaceable;
when the light source reaches its end of life the
whole luminaire shall be replaced.
This track is suitable for dimming. Fittings with low
voltage lamps are not suitable for dimming.
Care must be taken to only use the same type of
fitting that is able to be dimmed, and that the dimmer
wattage must not be exceeded.
Only to be installed outside arms reach.
0-350°
0-90°
80mm
79219/79303
Layout
This track system can be extended to a variety of different configurations using accessories such as left bends, right bends,
T jucntions, X junctions and flexible joints.
TJunction
X Junction
Bend
Dead End
0,5
IP20
Track accessory
183.0mm
35.0mm
183.0mm
Minimum distance from lighted objects (0.5 metres)
Class I product, must be connected to earth.
35.0mm
1000.0mm
2000.0mm
3000.0mm
182.0mm
35.0mm
183.0mm
35.0mm
35.5mm
35.0mm
108.0mm
108.0mm
79.5mm
294.0mm
108.0mm
108.0mm
35.0mm
35.0mm
Installation
• Plan the track layout and and decide accessories needed before fixing anything to the ceiling.
• The maximum power per run of track is 1kW (1000W).
• Ensure the ceiling is capable of holding the weight of the track and products. Take care to avoid damaging any
concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
• Mark the first hole position and fit the screw in position as shown.
• Feed the screw through the keyhole slot, and slide into position. Mark the position of the second hole.
• Locate the track and fit the second screw into position.
• If fitting accessories, remove the end cap, and push them firmly home. Fit extra lengths of track as required.
35.0mm
16.5mm
43.0mm
40.0mm40.0mm
Loading...