Wiring
• Having correctly identified the wiring from your existing light fitting, pull the mains wire through the hole and
connect to the quick fit connection block in the following way.
PUSH DOWN
INSERT CABLE
Check that...
• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.
Care and Safety
• We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could
damage the finish.
• For your safety, always switch off the supply before cleaning.
Instruction leaflet
Rond Microwave
78623, 78851, 78852, 78853
Iss 4 22/02/2019
www.saxbylighting.com Saxby Lighting. BH23 3PE
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and
qualified electrician.
Install in accordance with IEE Wiring regulations
and current Building Regulations.
Check the pack and make sure you have all of the
listed.
parts
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting.
Ensure other persons cannot restore the electrical
supply without your knowledge.
This light fitting should be connected to a circuit
with a 30mA RCD fitted.
If replacing an existing fitting, make a careful note
of the connections.
The mains supply cable must have a minimum
cross sectional area of 1.0mm².
The products can be wall or ceiling mounted.
If wall mounting ensure that the power supply is
at the bottom.
Cables must be protected using suitable conduit
or plastic trunking.
The external flexible cable or cord of this luminaire
cannot be replaced . if the cord is damaged, the
luminaire must be destroyed.
Waste electrical products should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authority or
retailer for recycling advice.
Technical data
Supply
Voltage:
Bulb Type:
240 V~, 50 Hz
LED (12 W) SMD 2835D 4000K
The light source of this luminaire is not replaceable; when the light source reaches its end of life
the whole luminaire shall be replaced.
Conformity with all relevant EC Directive requirements.
The power supply is Double Insulated and does not require connection to an Earth circuit.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist.Check with your Local Authority or
local store for recycling advice.
Layout
• Plan the desired layout of these fittings
carefully, ensuring the cables will reach
the distances between each light fitting.
• Avoid locating any cables in positions
that would cause a hazard. Position
cables and junction boxes (not supplied)
away from areas where they may be at
risk from being cut, trapped or damaged.
• This product is suitable for use in
Outside Zones of a bathroom only.
See diagram.
• If this unit is being fitted in a room
containing a bath or shower,
a 30mA RCD must be used in accordance with IEE regulations.
Microwave sensor
• The unit must be installed in a vertical position, and fitted
1.8m-2.5m above the ground.
• The MW detects in a fan-shaped arc of approximately 360°
for a distance up to 8 metres (depending on weather
conditions and the mounting height).
• The duration that the lamp stays on can also be altered from
2±5 seconds - 1 minute. 2 seconds is for self-test. When
connecting the electric, the fixture will keep lighting for
2 seconds then turn off. It will keep lighting for 1 minute
when detected.
The LUX range is <30 lux
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the
•
existing fitting, carefully note the position of each set of wires.
•
Note that the switch is closed before installation.
• The ceiling surface must be flat and smooth to ensure a good fit.
• Ensure the wall is capable of holding the weight of the product, or if fitting to a ceiling, ensure there is a
joist at the point of fixing to support the weight of the product. Take care to avoid damaging any concealed
wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
• The bezel can be replaced, but be careful to match the same color:
78851: Black plain 78852: Black eyelid 78852: White eyelid
• Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.
IP54
This product is not suitable for dimming.
Caution! Risk of electric shock!
This product is rated at IP54.
Used as wire entry coad grip
21
5 6 7
3
4
8
Loading...