Savin 2565, 2575 User Manual

Operating Instructions

Copy Reference

Placing Originals

Copying

Program

Troubleshooting

User Tools (Copy/Document Server Features)

Specifications

For safe and correct use of this machine, please be sure to read the Safety Information in the

General Settings Guide before you use it.

Type for 2560/6002/LD060 AG/Aficio 1060 Type for 2575/7502/LD075 AG/Aficio 1075 Printed in Japan

UE USA B064-6607

Introduction

This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine.

Notes

Some illustrations in this manual might be slightly different from the machine.

Certain options might not be available in some countries. For details, please contact your local dealer.

Laser Safety:

CDRH Regulations

This equipment complies with requirements of 21 CFR subchapter J for class 1 laser products. This equipment contains four 10-milliwatt, 770-810 nanometer wavelength, GaAIAs laser diodes. This equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes of operation and maintenance.

Warning:

Use of controls or adjustment or performance of procedures other than those specified in this manual might result in hazardous radiation exposure.

The model names of the machines do not appear in the following pages. Check the type of your machine before reading this manual. (For details, ⇒ p.2 “Machine Types”.)

• Type 1 : 2560/6002/LD060/Aficio 1060

• Type 2 : 2575/7502/LD075/Aficio 1075

Certain types might not be available in some countries. For details, please contact your local dealer.

Two kinds of size notation are employed in this manual. With this machine refer to the inch version.

For good copy quality, the supplier recommends that you use genuine toner from the supplier.

The supplier shall not be responsible for any damage or expense that might result from the use of parts other than genuine parts from the supplier with your office products.

Power Source

• 120V, 60Hz, 20A or more

Please be sure to connect the power cord to a power source as above. For details about power source, see “Power Connection” in General Settings Guide.

In accordance with IEC 60417, this machine uses the following symbols for the main power switch:

aaaa means POWER ON. cccc means STAND BY.

What You Can Do With This Machine

The following sections introduce the duplex and combining functions of this machine.

Types of Duplex Copies

1-sided 2 Pages 2-sided 1 Page p.43 " 1 Sided 2 Sided"

1-sided 4 Pages 2-sided 1 Page p.47 " 1 Sided 4 Pages Combine 2 Side"

1-sided 8 Pages 2-sided 1 Page p.47 " 1 Sided 8 Pages Combine 2 Side"

Front

Back

2-sided 1 Page 2-sided 1 Page p.43 " 2 Sided 2 Sided"

2-sided 2 Pages 2-sided 1 Page p.47 " 2 Sided 4 Pages Combine 2 Side"

2-sided 4 Pages 2-sided 1 Page p.47 " 2 Sided 8 Pages Combine 2 Side"

Front

Back

1-sided 16 Pages

2-sided 1 Page

p.47

" 1 Sided 16 Pages Combine 2 Side"

Front

Back

Bound Originals 2-sided Pages p.49 " Book 2 Sided"

2-sided 8 Pages

2-sided 1 Page

p.48

" 2 Sided 16 Pages Combine 2 Side"

Front

Back

Front/Back Bound Originals 2-sided Pages p.49 " Front & Back 2 Sided"

Copying Book Originals

1-sided 4 Pages Booklet ( P.50 " 1 Sided Booklet")

Open to Left

Open to Right

2-sided 2 Pages Booklet ( P.51 " 2 Sided Booklet")

Open to Left

Open to Right

1-sided Magazine ( P.51 " 1 Sided Magazine")

Open to Left

Open to Right

2-sided Magazine ( P.51 " 2 Sided Magazine")

Open to Left

Open to Right

Combining Multiple Pages onto a Single Page ( p.45 "1 Sided Combine")

1-sided 2 Pages 1-sided 1 Page 2-sided 1 Page 1-sided 1 Page

1-sided 4 Pages 1-sided 1 Page 2-sided 2 Pages 1-sided 1 Page

1-sided 8 Pages 1-sided 1 Page

Copying Originals Such as Books ( p.48 "Series Copies")

Bound Originals 1-sided Pages

Bound Originals 2-sided Pages

2-sided 4 Pages 1-sided 1 Page

Copying 2-Sided Pages onto 1-Sided Pages ( P.50 "2 Sided 1 Sided")

2-sided 1 page 1-sided 2 pages

Front/Back Bound Originals 2-sided Pages

iii

TABLE OF CONTENTS

What You Can Do With This Machine ...................................................................i

How to Read this Manual ......................................................................................1

Machine Types .......................................................................................................2

Functions that Require Options ...........................................................................3

Control Panel..........................................................................................................4

Common Key Operations ........................................................................................... 5

1. Placing Originals

Originals ................................................................................................................. 7

Sizes and Weights of Recommended Originals......................................................... 7

Sizes Detectable by Auto Paper Select .....................................................................8

Missing Image Area ................................................................................................. 10

Direction-fixed paper or 2-sided paper..................................................................... 11

Placing Originals..................................................................................................12

Original Orientation .................................................................................................. 12

Placing Originals on the Exposure Glass ................................................................. 13

Placing Originals in the Document Feeder............................................................... 13

2. Copying

Basic Procedure...................................................................................................17

Auto Start ................................................................................................................. 18

Interrupt Copy ..........................................................................................................18

Original Beeper ........................................................................................................ 18

Copy Face Up ..........................................................................................................19

Job Preset ................................................................................................................ 19

Copying onto Tab Stock ........................................................................................... 20

Copying from the Bypass Tray...........................................................................22

Copy Functions....................................................................................................25

Adjusting Copy Image Density ................................................................................. 25

Selecting Original Type Setting................................................................................ 26

Selecting Copy Paper ..............................................................................................27

Preset Reduce/Enlarge ............................................................................................ 30

Zoom ........................................................................................................................31

Auto Reduce/Enlarge ............................................................................................... 32

Size Magnification .................................................................................................... 33

Directional Magnification (%) ...................................................................................33

Directional Size Magnification (mm)......................................................................... 34

Sort...........................................................................................................................35

Stack ........................................................................................................................ 37

Staple ....................................................................................................................... 37

Sample Copy............................................................................................................ 40

Changing the Number of Sets .................................................................................. 40

Punch ....................................................................................................................... 41

Duplex ......................................................................................................................43

1 Sided Combine...................................................................................................... 45

2 Sided Combine...................................................................................................... 47

Series Copies ........................................................................................................... 48

2 Sided→1 Sided ..................................................................................................... 50

Copying Book Originals............................................................................................50

Image Repeat........................................................................................................... 53

Double Copies.......................................................................................................... 54

Centering..................................................................................................................55

Scanning Position .................................................................................................... 55

Erase........................................................................................................................56

3 Edges Full Bleed ................................................................................................... 61

Margin Adjustment ................................................................................................... 62

Background Numbering ...........................................................................................63

Preset Stamp ...........................................................................................................63

User Stamp ..............................................................................................................65

Date Stamp ..............................................................................................................68

Page Numbering ......................................................................................................69

Covers......................................................................................................................73

Designate ................................................................................................................. 74

Chapter .................................................................................................................... 75

Blank Slip Sheets ..................................................................................................... 76

Slip Sheets ............................................................................................................... 77

Storing Originals in the Document Server ........................................................78

3. Program

Programs .............................................................................................................. 79

Storing a Program .................................................................................................... 79

Deleting a Program .................................................................................................. 80

Recalling a Program................................................................................................. 80

4. Troubleshooting

If Your Machine Does Not Operate as You Want ..............................................83

When a Message is Displayed................................................................................. 83

If You Cannot Make Clear Copies.......................................................................84

If You Cannot Make Copies As You Want .........................................................85

When Memory Is Full ............................................................................................... 87

5. User Tools (Copy/Document Server Features)

User Tools Menu (Copier/Document Server Features) ....................................89

Accessing User Tools (Copy/Document Server Features) ..............................96

Exiting From User Tools........................................................................................... 96

General Features

Reproduction Ratio

/2....................................................................................................................101

Edit

/2....................................................................................................................102

Edit

/5................................................................................................97

/5................................................................................................99

/5..............................................................................................100

/2........................................................................................... 100

Stamp..................................................................................................................... 104

Input/Output

/2...................................................................................................... 106

/2....................................................................................................... 107

6. Specifications

Combination Chart............................................................................................. 109

Supplementary Specifications..........................................................................111

INDEX....................................................................................................... 125

How to Read this Manual

Symbols

In this manual, the following symbols are used:

WARNING:

This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section in the General Settings Guide.

CAUTION:

This symbol indicates a potentially hazardous situation that might result in minor or moderate injury or property damage that does not involve personal injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section in the General Settings Guide.

• WARNINGS and CAUTIONS are notes for your safety.

Important

If this instruction is not followed, paper might be misfeed, originals might be damaged, or data might be lost. Be sure to read this.

Preparation

This symbol indicates the prior knowledge or preparations required before operating.

Note

This symbol indicates precautions for operation or actions to take after misoperation.

Limitation

This symbol indicates numerical limits, functions that cannot be used together, or conditions in which a particular function cannot be used.

Reference

This symbol indicates a reference.

[]

Keys that appear on the machine's display panel.

{}

Keys built into the machine's control panel.

Notice

•B4 JISKL, B5 JISKL, B6 JISL are referred as B4KL, B5KL, B6L in this

manual.

• The image of the display panel may be different depending on the installed option.

Machine Types

This machine comes in two models which vary by copy speed. To make sure which model you have, see the inside front cover.

Type 1 Type 2

Copy speed 60 copies/minute (A4K, 8

× 11"K)

/2"

75 copies/minute (A4K, 8 × 11"K)

/2"

Functions that Require Options

Available functions depend on your machine configuration and which options you have. See the table below.

❍Required options

Functions

Copying onto the Tab Stock

Shift Sort

Stack

Staple

Staple (Saddle Stitch)

Punch

Tab Sheet Holder ❍

Finisher 3000M(50-sheet staples) ❍❍❍ ❍

Booklet Finisher ❍❍❍❍❍

Finisher 3000B(100-sheet staples) ❍❍❍ ❍

Options

To use the Punch function, you need an optional Punch Unit.

Control Panel

Note

❒ This illustration shows the Control Panel of the machine with options fully in-

stalled.

ZGVS300N

1. Screen Contrast knob

Adjusts the brightness of the display panel.

2. Indicators

These indicators show the status of the machine or indicate errors. ⇒ “Control Panel” in the General Settings Guide.

{{{{User Tools/Counter}}}} key

• User Tools Press to change the default settings and conditions to meet your requirements. ⇒ p.89 “ User Tools (Copy/Document Server Features)”

• Counter Press to check or print the Counter value. ⇒ “Counter” in the General Settings Guide.

• Inquiry Shows where to order expendable supplies and where to call when a malfunction occurs. You can also print these details. ⇒ “Inquiry” in the Gen- eral Settings Guide.

6. {

{Program}}}} key

{{

Press to store or recall a program. ⇒ p.79 “Programs”

7. {

{Clear Modes}}}} key

{{

Press to clear previously entered copy job settings.

8. {

{Energy Saver}}}} key

{{

Press to switch to and from Energy Saver mode. ⇒ “Saving Energy” in the General Settings Guide.

9. {

{Interrupt}}}} key

{{

Press to interrupt a long copy job to make copies. ⇒ p.18 “Interrupt Copy”

10.

Main power indicator, On indi-

cator

The main power indicator goes on when the main power switch is turned on and goes off when the switch is turned off.

The On indicator goes on when the operation switch is turned on and goes off when the switch is turned off.

4. Display panel

Shows operation status, error messages, and function menus. ⇒ “Display Panel” in the General Settings Guide.

5. {

{Check Modes}}}} key

{{

Press to check the entered copy job settings.

Important

❒ Do not turn the main power off

while the On indicator is flashing. The hard disk may malfunction.

11. Operation switch

Press this switch to turn the power on (the On indicator goes on). To turn the power off, press this switch again (the On indicator goes off). ⇒”Turning On the Power” in the General Settings Guide.

12. Clip Tray

Holds clips and staples.

13. {

{Sample Copy}}}} key

{{

Use this key to make a single sample copy before starting a long copy run. By checking the sample copy and making any necessary changes to the image quality settings before you make multiple copies, you can save time and paper. ⇒ p.40 “Sample Copy”

14. {

{Start}}}} key

{{

Press to start copying. Press to start scanning and printing in Document Server mode.

{{{{Clear/Stop}}}} key

15.

• Clear Press to delete a number entered.

• Stop Press to stop a copy job in progress. Press to stop Scanning and printing in Document Server mode.

16. {

{#}}}} key

{{

Press to enter a value.

17. Number keys

Use to enter the desired number of copies, and data for selected modes.

18. Function keys

These keys switch display to the operating screen of each function. Follow the instructions displayed by switching between screen with the function keys.

19. Function Status indicator

These show the status of the above functions:

• Green: the function is active.

• Red: the function has been interrupt-

ed.

Common Key Operations

The following keys are common to all screens.

[

] Returns to the previous screen.

Exit

[

] Deletes a selected function or entered values, and then returns

Cancel

to the previous screen.

[OK] Acknowledges a selected function or entered values, and then

returns to the previous screen.

[▲

Prev.

] [▼

] Moves to the previous or next page when all the functions can-

not be displayed on one page.

1. Placing Originals

Originals

Sizes and Weights of Recommended Originals

❖❖❖❖ Metric version

Where Original Is Placed Original Size Original Weight

Exposure glass Up to A3 --

Document feeder 1-sided originals:

A3L – B6KL

2-sided originals: A3L – A5KL

40 – 128 g/m

52 – 128 g/m

❖❖❖❖ Inch version

Where Original Is Placed Original Size Original Weight

Exposure glass Up to 11" × 17" --

Document feeder 1-sided originals:

11" × 17" L – 5

2-sided originals: 11" × 17" L – 5

/2" × 81/2"KL

11 – 34 lb.

14 – 34 lb.

Note

❒ The number of originals that can be placed in the document feeder is about

100.

❒ The weight range for originals in the Mixed Size mode is 52–81.4 g/m

, 13.8–

21.7 lb.

Non-recommended originals for the document feeder

Placing the following types of originals in the document feeder can cause paper misfeeds or result in damage to the originals. Place these originals on the exposure glass instead.

• Originals other than those specified in p.7 “Sizes and Weights of Recommended Originals”

• Stapled or clipped originals

• Perforated or torn originals

• Curled, folded, or creased originals

• Pasted originals

Placing Originals

• Originals with any kind of coating, such as thermal fax paper, art paper, aluminum foil, carbon paper, or conductive paper

• Originals with perforated lines

• Originals with indexes, tags, or other raised parts

• Sticky originals such as translucent paper

• Thin originals that have low stiffness

• Thick originals such as postcards

• Bound originals such as books

• Transparent originals such as OHP transparencies or translucent paper

Note

❒ The original might become dirty if it is written on with a pencil or similar

instrument.

Sizes Detectable by Auto Paper Select

❖❖❖❖ Metric version

Size A3LB4LA4

original

Exposure glass ❍❍❍❍ ЧЧЧЧЧЧ❍ ××

Document feeder

You can select from 81/2" × 13", 81/4" × 13" or 8" × 13" with the User Tools (System Settings). See "<F/F4>Size Setting" in the General Settings Guide.

If you wish to switch detectable paper size from 8K L to 11" × 17" L, please contact your service representative.

If you wish to switch detectable paper size from 16K K to 81/2" × 11" K or from 16K L to 8

❍❍❍❍❍❍❍

/2" × 11" L, please contact your service representative.

K L

11" × 17"

81/2"

51/2"

81/2"

14"

11"

❍

/2"

13"

❍❍❍

16K

K LLocation of the

❖❖❖❖ Inch version

Size A3LB4LA4

Location of the original

Exposure glass ЧЧЧЧЧ

Document feeder

❍

K L

❍

××

81/2"

11"

51/2"

/2"

ЧЧЧЧЧ

11"

14"

17"

❍❍❍

❍❍❍❍❍

81/2"

11"

13"

15"

*1 ❍ *2 ❍ *3

8" × 10"

10" × 14"

❍

If you wish to switch detectable paper size from 81/2" × 14"L to 81/2" × 13" L, please contact your service representative.

If you wish to switch detectable paper size from 11" × 17" L to 11" × 15" L, please contact your service representative.

If you wish to switch detectable paper size from 81/2" × 11" L to 8" × 10" L, please contact your service representative.

❖❖❖❖ Exposure glass

Originals

Reference position

Horizontal size

Vertical size

A3A4

❖❖❖❖ Document feeder

Maximum Scanning area A3 (297 x 420 mm) 11" x 17"

(279 x 432 mm)

CP01AEE

Sizes difficult to detect

It is difficult for the machine to detect the sizes of the following originals, so select manually.

• Originals with indexes, tags, or other raised parts

• Transparent originals such as OHP transparencies or translucent paper

• Dark originals with a lot of text and drawings

• Originals that partially contain a solid image

• Originals that have solid images at their edges

Placing Originals

Missing Image Area

Even if you correctly place originals in the document feeder or on the exposure glass, margins of a few millimeters on all four sides of the original might not be copied.

1. 0.5 mm, 0.02”

2. 1 mm or more, 0.04” or more

3. 0.5 mm - 3.5 mm, 0.02” - 0.14”

4. 2 - 6 mm, 0.08”- 0.24”

Originals

Direction-fixed paper or 2-sided paper

Direction-fixed (top to bottom) or 2-sided paper (e.g., letterhead paper, punched paper, or copied paper) might not be printed correctly depending on how the originals and paper are placed. Set "Letterhead setting" in system settings, and then place the original and paper as shown below. ⇒ p.108 “Letterhead Setting”

Placing Originals

Note

❒ Place originals after correction flu-

id and ink have completely dried. Not taking this precaution could dirty the exposure glass with marks that will be copied.

Reference

For document sizes you can set. ⇒ p.7 “Originals”.

Original Orientation

When you place the original into the document feeder, place it face up so you can see the print.

When you place the original on the exposure glass, place it face down.

Example: When you want to staple copies, but you cannot select because the original size is A3K, selecting enables you to staple copies correctly.

1. Document feeder

2. Exposure glass

When you cannot place originals as described because the size is A3 or A4 or because of its condition, you cannot staple copies as you want. In this case, select as the Original Orientation.

Note

❒ It is recommended to use this func-

tion together with the Auto Paper Select or Preset Reduce/Enlarge function.

Press the [Special Original] key.

AAAA

Select the original orientation

BBBB

( or ) and press the [OK] key.

Placing Originals

Placing Originals on the Exposure Glass

Reference

Related Initial Settings ⇒ p.108 “Eject Copy Face Up/Down in Glass”

Lift the exposure glass cover or

AAAA

the document feeder.

Important

❒ Do not open the exposure glass

cover or the document feeder forcefully. Otherwise, the cover of the document feeder might open or be damaged.

Note

❒ Be sure to open the exposure

glass cover or the document feeder by more than 30°. Otherwise, the size of the original might not be detected correctly.

Place the original face down on the

BBBB

exposure glass. The original should be aligned to the rear left corner.

Placing Originals in the Document Feeder

Settings should be made in the following situations:

❖❖❖❖ When placing originals one by one:

⇒ p.15 “SADF mode”

❖❖❖❖ When placing originals consisting of

more than 100 pages:

⇒ p.14 “Batch mode”

❖❖❖❖ When copying originals of various

sizes:

⇒ p.15 “Mixed Size mode”

❖❖❖❖ When placing custom size originals:

⇒ p.16 “Placing Custom Size Orig- inals”

Note

❒ Do not stack originals beyond the

limit mark on the side fence of the document feeder.

❒ The last page should be on the bot-

tom.

❒ When you copy 2–sided originals,

both front and back sides of each original are scanned at once.

1. Reference mark

2. Left scale

Note

❒ Start with the first page to be

copied.

Lower the exposure glass cover or

CCCC

the document feeder.

❒ Do not place any foreign objects on

the sensors or cover them with your hands. This could cause a malfunction or the size to not be detected properly.

1. Sensors

Placing Originals

Set the document guide to the

AAAA

original size.

Align the edges of the original

BBBB

and place it on the document feeder (ADF) with the side to be copied facing up.

1. Limit mark

Batch mode

In batch mode, the machine copies an original of more than 100 pages as one document, even if it is placed on the document feeder in parts.

Important

❒ When placing special originals

such as translucent paper, place one by one.

Press the [Special Original] key.

AAAA

2. Document guide

Note

❒ Straighten curls in the original

before placing it on the document feeder (ADF).

❒ To prevent multiple sheets from

being fed at once, fan the original before placing it on the document feeder (ADF).

❒ Set the original squarely.

Select the [Batch] key, and then

BBBB

press the [OK] key.

Note

❒ When [Batch] is not displayed,

change the settings in ⇒ p.106 “Switch to Batch (SADF)”.

Place the first part of the original,

CCCC

then press the {{{{Start}}}} key.

After the first part of the original

DDDD

has been fed, place the next part and then press the {{{{Start}}}} key.

Note

❒ If you want to copy subsequent

originals in this mode, repeat step D.

When the Sort, Combine or 1 Sid-

EEEE

ed →→→→ 2 Sided mode has been set, press the {{{{#}}}} key after all originals have been scanned.

Placing Originals

SADF mode

In SADF mode, even when an original is placed page by page in the document feeder (ADF), each page is automatically fed when placed.

Preparation

To use the SADF function, you should make a setting in "User Tools (Copy/Document Server Features)", so that [SADF] will be displayed when you press [Special Original]. ⇒ p.106 “Switch to Batch (SADF)”

Reference

Related Initial Settings ⇒ p.106 “SADF Auto Reset”

Press the [Special Original] key.

AAAA

Mixed Size mode

When you place different size originals in the document feeder at the same time, the machine automatically checks the size of the originals and makes copies.

Note

❒ When placing originals of different

sizes in the document feeder and making copies without using the Mixed Size mode, parts of the original image might not be copied or paper might become jammed.

❒ The sizes of the originals that can

be placed together with this function are as follows:

Metric version

Inch version

A3L , B4L, A4KL , B5KL

11" × 17"L , 8

/2" × 11"KL , 51/2" ×

/2" × 14"L,

Press the [SADF] key, and then

BBBB

press the [OK] key.

Place one page of an original, and

CCCC

then press the {{{{Start}}}} key.

The Auto Feed indicator is shown on the display.

When the machine instructs you

DDDD

to place another original, place the next page.

The second and subsequent pages will be fed automatically without pressing the{{{{Start}}}} key.

Press the [Special Original] key.

AAAA

Press the [Mixed size] key, and then

BBBB

press the [OK] key.

Placing Originals

Align the rear and left edges of

CCCC

originals as shown in the illustration.

1. Place into the document feeder.

2. Vertical size

Adjust the guide to the widest

DDDD

original size.

Place aligned originals face up

EEEE

into the document feeder. Press the {{{{Start}}}} key.

FFFF

Placing Custom Size Originals

CP19AE

Enter the horizontal size of the

CCCC

original with the Number keys, and then press the [#] key.

Note

❒ If you make a mistake, press the

[Print Inquiry List] or {{{{Clear/Stop}}}} key, and then enter the value again.

Enter the vertical size of the origi-

DDDD

nal with the Number keys, and then press the [#] key.

Press the [OK] key.

EEEE

Place originals, and then press the

FFFF

{{{{Start}}}} key.

When placing custom size originals in the document feeder, specify the size of the originals.

Note

❒ Paper that has a vertical length of

128–297 mm (5" – 11") and a horizontal length of 128–1260 mm (5" –

49.6") can be placed with this function.

Press the [Special Original] key.

AAAA

Press the [Custm Size Origi.] key.

BBBB

Basic Procedure

2. Copying

When the machine is set for user

AAAA

codes, enter a user code (up to 8 digits) with the number keys, and then press the {{{{#}}}} key.

The machine is ready to copy.

Reference

For Users Code, see ⇒“Key Operator Tools” in the General Settings Guide.

Make sure "Ready" is displayed

BBBB

on the screen.

If any other function is displayed, press the {{{{Copy}}}} key.

❖❖❖❖ Initial copy display

Set desired settings.

EEEE

Reference

Please refer to each functions.

Enter the number of copies re-

FFFF

quired with the number keys.

Note

❒ The maximum copy quantity

that can be set is 999.

Press the {{{{Start}}}} key.

GGGG

The machine starts copying.

Note

❒ When you place originals on the

exposure glass, press the {{{{# }}}} key after all originals are scanned.

❒ Copies are delivered face down.

Make sure there are no previous

CCCC

settings remaining.

Note

❒ When there are previous set-

tings remaining, press the {{{{Re- set}}}} key and enter again.

Place originals.

DDDD

Reference

⇒ p.12 “Placing Originals”

----How to Operate

❖❖❖❖ To stop the machine during a multi-

copy run.

⇒Press the {{{{Clear/Stop}}}} key.

❖❖❖❖ To return the machine to the initial

condition after copying.

⇒Press the {{{{Clear Modes}}}} key.

❖❖❖❖ When clearing entered values.

⇒Press the {{{{Clear/Stop}}}} key or the [Clear] key on the display.

❖❖❖❖ To confirm settings.

⇒Press the {{{{Check Modes}}}} key.

+ 61 hidden pages