The Savant Wi-Fi Circa Switch (WCS-1XXXXX) and the Wi-Fi Circa Dimmer (WCD-1XXXXX)
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 90% Relative Humidity (non-condensing)
Dimensions with Faceplate
Height
4.67 in / 11.87 cm
Width
3.04 in / 7.72 cm
Depth
1.82 in / 4.63 cm
Power
Supply
120 V AC 60 Hz
Load Power
Minimum
3 watts per gang
Maximum
For the one gang (WCS-1XXXXX or WCD-1XXXXX):
•
800 watts (for dimmer and relay versions)
1 - 1 gang = 800W
2 – 1 gang = 700W ,700W = 1400W
3 – 1 gang = 600W, 600W, 600W = 1800W (Breaker maximum)
4 – 1 gang = 450W,450W,450W,450W = 1800W (Breaker maximum)
For the two gang (WCC-2XXXXX):
•
550 watts per channel (1100 watts total)—the maximum rating for
dimmer version (no relay version on two gang)
•
If a one-gang and two-gang are used together, assume the
maximum load of each.
Compliance
Safety and
Emissions
FCC Part 15 | CE Mark | C-Tick | UL
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation. Any changes or modifications of this product,
not approved by manufacturer will void the user’s authority to operate the
equipment.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
RoHS
Compliant
Minimum Requirement: Release LiteWare 5.2.2
Ter min al
Wire Color
Purpose
Load
Black
Connects to light/load, fan or fireplace
Neutral
White
Neutral
Line
Black
Hot/Live (120 V AC: 12-14 AWG)
Ground
Green
Ground
Feature Summary
• Supports Wi-Fi™ (IEEE 802.11 b/g)
• Circa keypad that functions as a dimmer or a
switch within a SmartLighting configuration
• Ganging wall box dimmers/switches is faster with
alignment plate technology
• Ideal for retro-fit installations
• Single-gang configurations of one, two, or three
buttons
• Standard and premium faceplate finishes
• Custom engraved buttons: multiple languages
and icons are available
• 13 field-adjustable LED colors are software
configurable
• Controlled by Savant Lighting app or Savant
TrueControl app
• Use LiteWare™ to configure lighting in Savant
SmartLighting control system
• Use RacePoint Blueprint™ design tool to
integrate into Savant Systems
Service Switch
LED Level
SmartConnect
Connector
Push to Test
Button
Diagnostic LED
Port
Diagnostic LED
See Diagnostic LEDs on the next page.
Push to Test button
Press to test Load
SmartConnect Port
Interface for the SmartConnect Accessory
LED Level
Rotate wheel to adjust the brightness intensity level of text/icons
Service Switch
Pull down the switch to disconnect power from the keypad and
load for service. Push up the switch to reconnect the power.
Load 1
Neutral (white)
Line (black)
Ground (green)Service Switch
Wi-Fi™ Circa Switch and Dimmer Keypads
(WCS-1XXXXX and WCD-1XXXXX)
Quick Reference Guide
009-1002-03
WCS-1XXXXX-00
WCD-1XXXXX-00
quick reference guide provides the information necessary to install either Wi-Fi Circa keypad.
The Wi-Fi Circa switch contains one relay, and functions as a one-gang switch to turn on/off
relay-controlled devices, such as lights, fans, and fireplaces. The Wi-Fi Circa Dimmer functions
as a single gang forward phase dimmer. These keypads can be combined in gangs up to four in
a wall. Both keypad types must have a lighting controller: for example, an SSL-P018 or SSLP002 (wired) via a network router, to operate correctly. The SmartConnect Accessory and the
SmartConnect app enable the WCS-1XXXXX or WCD-1XXXXX to be configured with an iOS
user interface. The Savant plastic faceplate is included, by default the same color as the switch
or dimmer.
Front View of Three-Button WCS-1XXXXX or WCD-1XXXXX with Faceplate
Box Contents
(1) WCS-1XXXXX or (1) WCD-1XXXXX
(1) Faceplate
(2) 6-32 x1 Flat Phillips Screw (039-0103-xx)
(1) Quick Reference Guide (this document)
Optional Components
SmartConnect Accessory (SCA-CONFL)
SmartConnect app
Specifications
Rear View of WCD-1XXXXX or WCS-1XXXXX
Warning: A licensed electrician is
required to install any Savant Circa
Wi-Fi™ keypad.
NOTE: Savant recommends a U.S. back
box with a depth of 3.5 in/8.89 cm.
Minimum depth is 2.5 in/6.35 cm
Front View of WCD-1XXXXX or WCS-1XXXXX
! ! 1 of 4
011414
The Service Switch
is used to disconnect
power to the load for
service.
Installing a Wi-Fi Keypad
Main Button Functionality
The main buttons on the Wi-Fi dimmer/switch keypad are fully programmable when the
dimmer/switch is attached to a SmartLighting controller—wireless (WCC-2XXXXX or SSL-
W002) or wired (SSL-P018 or SSL-P002). When not connected to a controller, the main
buttons on a three-button keypad and LEDs will operate as follows:
Top button - Toggle the load to 100%. Holding the button will ramp the load up or down.
Middle button - Same as top button.
Bottom button - Same as top button.
10 Levels of Backlight
Level 1 - no backlight, no nightlight.
Level 2, 3,and 4 - 10%, 20%, 30% nightlight brightness.
Level 5-10 - nightlight off, backlight levels from 10% to 100%.
Nightlight means the backlight is OFF, and the indicator LED is on
at a level that is much dimmer than the LED ON state.
LED State
Description
OFF
The Wi-Fi dimmer/switch keypad is functional. The keypad is associated
with the access point, and bound to the controller.
Dim
(ON)
Associated with the access point, but not bound to the controller.
All buttons will control the local load as a dimmer/switch.
Bright
(ON)
Not associated with the access point. Connect the SmartConnect
Accessory (SCA-CONFL) and set the Wi-Fi settings.
If the Wi-Fi settings are correct, check that the access point is powered on
and set with correct credentials.
In this mode, all buttons will control the local load as a dimmer/switch.
Green
Blinking
The WCS-1XXXXX or WCD-1XXXXX is running the firmware updater. A
firmware update may not have completed successfully. In this case, you
must rerun the firmware update.
In this mode, the dimmer/switch will not control the local load.
LED State
Description
Press
A press with no hold will turn on the load and will flash the PTT LED
on bright regardless of the connection state. Pressing the button
again will exit PTT mode and return to normal operation.
Hold
(WCD-1XXXXX
only)
When this button is held for more than two seconds, the snubber
mode will be changed to the next available mode at two seconds,
four seconds and six seconds. When the button is released, the
current snubber mode will be saved to flash.
LED
The PTT LED will change color to indicate the snubber mode as
follows (WCD-1XXXXX only):
Green - (default) turn snubber on when the load is off
Red - snubber always off (magnetic loads)
Blue - snubber always on (LED loads)
Hold for 10 seconds: Reset to factory defaults - Wi-Fi settings will be
deleted and the Wi-Fi dimmer will revert to factory default mode. On
reboot the dimmer will attempt to connect to the open
SavantDevices access point (Savant controller).
Hold during boot: If you hold the diagnostic button for three seconds
while the dimmer is booting, the dimmer will go into GainSpan
programming mode. In this mode the SmartConnect port is internally
routed to the GainSpan for programming through a SmartConnect
cable.
Wi-Fi™ Circa Switch and Dimmer Keypads
(WCS-1XXXXX and WCD-1XXXXX)
Quick Reference Guide
009-1002-03
WCS-1XXXXX-00
WCD-1XXXXX-00
To install a WCS-1XXXXX or WCD-1XXXXX, see Installing a WCS-1XXXXX or WCD-1XXXXX.
Setting Up The Controller
After all Savant Wi-Fi keypads are installed and connected to the local network, follow the
instructions in the Savant Wi-Fi Keypad Deployment Guide (009-0971-XX) to complete the
installation.
If you are using a wired controller—for example, SSL-P002 or SSL-P018—to control the Wi-Fi
keypads, see the Savant Keypad Deployment Guide (009-0610-XX).
Diagnostic LEDs
The following descriptions assume the Wi-Fi dimmer/switch keypad is connected properly and
powered on.
Installing a WCS-1XXXXX or WCD-1XXXXX
The Wi-Fi keypads are designed to be replacements for a toggle switch for regular household
lighting. The WCD-1XXXXX functions as a single dimmer. The WCS-1XXXXX is used to relaycontrolled devices such as lights, fans, and fireplaces. Both the WCD-1XXXXX and the
WCS-1XXXXX require a Savant Light control system. A minimum system could consist of a
single controller, WCC-2XXXXX or any Savant SSL controller and a single WCD-1XXXXX or
WCS-1XXXXX. A licensed electrician is required to install any Wi-Fi keypad.
ELECTRIC SHOCK: The 120 V AC, 60 Hz source power poses an electric
shock hazard that has the potential to cause serious injury to installers and
end-users.
Push to Test Button
When you first install the WCS-1XXXXX or WCD-1XXXXX, the Push To Test (PTT) button can
be used to test the load connected to the dimmer/switch. This button also can be used to change
the dynamic snubber mode (WCD-1XXXXX only).
The PTT LED (also referred to as a diagnostic LED) will turn on at boot and will go dim when the
dimmer/switch connects to an access point.
The PTT LED color is based on the snubber mode as described in the next table
(WCD-1XXXXX only).
The PTT LED will flash when in Push To Test mode.
Additional Documentation
Additional information is available at: dealers.SavantSystems.com:
Dealer Login > Knowledge Base > Savant Hardware > Keypads
See also the Savant Wi-Fi Keypad Deployment Guide (009-0971-XX)
For details on adding audio/video control to keypad buttons, see the Savant Keypad Deployment
Guide (009-0610-XX)
! ! 2 of 4
011414
IMPORTANT: A licensed electrician is required to install any Wi-Fi™ keypad.
Isolate and turn off the power from the main power supply to the switch or
keypad that is to be replaced.
Single Location Installation
Three-Way Replacement Installation
Installation of Wi-Fi™ Keypads
The Wi-Fi keypads are designed to be replacements for a toggle switch for regular household lighting. The WCC-2XXXXX
keypad functions as two dimmers and a controller. The WCD-1XXXXX functions as a single dimmer. The WCS-1XXXXX is
used to relay-controlled devices such as lights, fans, and fireplaces. Both the WCD-1XXXXX and the WCS-1XXXXX require a
Savant Light control system. A minimum system could consist of a single controller, WCC-2XXXXX or any Savant SSL
controller and a single WCD-1XXXXX or WCS-1XXXXX. The WCC-2XXXXX could also be a standalone system. A licensed
electrician is required to install any Wi-Fi keypad.
ELECTRIC SHOCK: The 120-240V AC, 50/60 Hz source power poses an electric shock hazard that has the
potential to cause serious injury to installers and end-users.
IMPORTANT: A licensed electrician is required to install any Wi-Fi™ keypad. Isolate and turn off the power from
the main power supply to the switch/keypad that is to be replaced.
Parts Identification and Installation
Illustrated below is the mounting sequence and parts for the WCD-1XXXXX, WCS-1XXXXX, and WCC-2XXXXX keypads.
Savant recommends a U.S. back box with an optimal depth of 3.5 in (8.89 cm). A minimum depth of 2.5 in (6.35 cm) is
acceptable.
WCD-1XXXXX and WCS-1XXXXX
Back Box Circa Keypad Faceplate
Phillips
Screws (2)
Wi-Fi™ Circa Switch and Dimmer Keypads
(WCS-1XXXXX and WCD-1XXXXX)
Quick Reference Guide
009-1002-03
WCS-1XXXXX-00
WCD-1XXXXX-00
NOTE: This installation
requires network availability.
Electrician Installation Instructions
To ensure proper installation of your Wi-Fi keypads, a qualified electrician should do the
following.
1. Turn off the power from the main power supply to the switch/keypad that is to be
replaced.
2. Unscrew the wall plate and remove.
3. Remove existing toggle/rocker switch or analog dimmer.
4. Unscrew the sheathed, insulated wires (Romex) from the screw terminals.
5. Remove switch box.
6. Connect the in-wall Romex wires to the correct screw terminals on the Wi-Fi keypad and
tighten terminals.
7. Insert the Wi-Fi keypad into the backbox and secure with the screws provided.
8. Re-establish power from the main power supply.
Important! For back-boxes without neutral wires, they will have to be rewired to
contain both a hot and neutral wire to power the controller on the switch.
To replace three-way switches, determine which gang actually controls
the load. After that is determined, wire the neutral and hot wires from box
to box so that they are not switched. For switches that are not wired to a
load, leave their load connector bare.
Parts Identification and Installation
The next diagram shows the mounting sequence and parts for the WCD-1XXXXX or
WCS-1XXXXX keypads. Savant recommends a U.S. back box with an optimal depth of 3.5 in
(8.89 cm). A minimum depth of 2.5 in (6.35 cm) is acceptable.
! ! 3 of 4
011414
Setting Up Wi-Fi Using SmartConnect
Micro USB-B
(male)
Fields
Valu e
IP Address
IP address to be assigned to the Savant SmartPlug
Subnet Mask
Subnet Mask of your network. Check with your network administrator.
(Typically this will be 255.255.255.0.)
Gateway
Gateway IP of your network. Check with your network administrator.
(This is the IP address of the router.)
DNS Server
DNS server of your network. Check with your network administrator.
Wi-Fi™ Circa Switch and Dimmer Keypads
(WCS-1XXXXX and WCD-1XXXXX)
Quick Reference Guide
009-1002-03
WCS-1XXXXX-00
WCD-1XXXXX-00
This procedure assumes that you have already installed the Savant SmartConnect app on your iOS
device, and that you have connected the SmartConnect cable to the appropriate Savant device and
iOS device. The next procedure applies to SmartConnect accessory or SCA-CONFL.
SmartConnect using SCA-CONFL
To configure your Savant Wi-Fi keypad wireless network settings using the SmartConnect app
when the Wi-Fi network is not available on an iOS device, do the following.
1. Remove the faceplate.
2. Connect the SmartConnect Accessory (SCA-CONFL) to the iOS device.
3. Open the SmartConnect app on the iOS device.
4. Attach the SmartConnect adapter to the Wi-Fi keypad on the front of the keypad.
5. In the app, select the Single Gang Wi-Fi selection.
6. Select the Wi-Fi row.
7. Select a network under Recent networks (recently-used Wi-Fi network of the iOS device) or
select Other… to manually configure the network settings.
8. Enter a network Name.
9. Tap Security and then select an option.
10. Tap Password to open the keyboard and then enter the network password.
11. Tap t h e Join button.
If a static IP address is required, return to the Wi-Fi screen and select the Static tab. Next, enter
the IP Address, Subnet Mask and Router information. Tap Apply.
Configuring Wi-Fi for Keypads Using the Web Interface
To configure the Wi-Fi network settings for a WCD-1XXXXX or WCS-1XXXXX using a Web
interface, do the following.
1. From a Savant-supported Web browser, enter 192.168.1.1/network.html in the address bar.
If prompted, enter the user name: RPM, and password: RPM.
2. Click Select an Existing Network.
5. If you selected a secured network, enter a value (up to 63 characters) in Passphrase and
Confirm Passphrase.
If you prefer to configure a static IP address, insert a check mark for Advanced Options.
Select Static IP Address Configuration.
Use the next table to enter values for the fields under Advanced Options (if configuring a static
IP address).
6. Click Next. A summary of your network settings is displayed.
3. View the existing wireless networks.
From the Network Settings page, you can choose an unsecured network or secured
network, and set up a static IP address (if required). For example, if you select a network
with Wi-Fi Protected Access (WPA or WPA2), you will be prompted to enter a passphrase.
4. Click the Select button beside the network you wish to join. See the next example
screenshot, which shows WPA or WPA2 security.
! ! 4 of 4
011414
7. Click Save and Apply.
Copyright © 2014 Savant Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.
All brand names, product names and trademarks are the property of their respective owners.
Savant Systems, LLC reserves the right to change product specifications without notice.
Loading...