Power LED Green: System has power and is operating normally.
Red: System is in standby mode and most of the
controller circuitry is powered down.
O: System is not receiving power.
Status LED Green Blinking: Embedded system is ready, but no
communication has been established with the host.
Green: Host has established communications with the
embedded system.
Red Blinking: Embedded firmware is running, but has
not received a DHCP IP Address.
Red: Host has determined the firmware needs to be
updated, but a problem occurred during the process
that will initiate a reset.
Amber Blinking: Embedded system has a valid
link-local IP Address and is connecting to the host.
Amber: Host is updating the embedded firmware.
O: Embedded processor is resetting, or is powered
up, and is booting the embedded firmware.
Hardware Failure: If a hardware failure occurs, the
status LED indication will be interrupted every three
seconds with a solid red indication. For example, if the
LED is blinking green when a hardware failure occurs,
the LED will alternate between blinking green and
solid red at three-second intervals.
RS232 LED Green: RS-232 serial port activity.
O: No RS-232 serial port activity.
IR LED Green: IR port signal activity.
O: No IR port activity.
On/O Button On: Fully enables all internal power rails and processor.
O: Disables most internal power rails and processor,
but not internal AC/DC power supply.
Hold On/O button for about 5 seconds to place
into standby mode. The Power LED turns red. Hold
On/O button for about 1 second to take system out
of standby mode. The I/O power switch on the back
of unit must be On (I) to enable this function. To turn
the power o for the entire system, press the I/O
power switch on the rear panel to O [O].
Reset Button Resets the network.
Hold Reset Button for 5 seconds while powered On
to clear network settings. Status LED will rapidly blink
red when reset is complete.
Zone Protection Red: Protection mode has been enabled to protect
a zone/channel; typically indicates thermal protection,
clipping or over current.
O: Protection mode has not been enabled.
ENCLOSURE INSTALLATION
The Savant Pro Audio 4 device can be mounted to a Structured Media
Enclosure. The Enclosure Brackets need to be attached prior to mounting.
For proper ventilation, louvered enclosure doors are recommended. See Pro
Audio 4 Deployment Guide for more information.
A
B
E
C
D
F
G
FRONT PANEL
SAVANT PRO AUDIO 4
QUICK REFERENCE GUIDE
BOX CONTENTS – SKU: SMA-5000
(1) Savant Pro Audio 4 (model: SPA-5000-xx)
(2) Enclosure Bracket (071-1103-xx)
(1) 2U Rack Bracket (071-1102-xx)
(1) Power Cord (064-0079-xx)
(4) #10x½ Screw (039-0405-xx)
(4) Push Rivet (039-0406-xx)
(6) M4 Screw (039-0403-xx)
(4) 4-pin Speaker Connector (028-0702-xx)
(2) 4-pin IR Connector (028-0703-xx)
(4) Rubber Feet (074-0655-xx)
(4) M3 Feet Screw (039-0407-xx)
(1) Quick Reference Guide (this document)
SPECIFICATIONS
ENVIRONMENTS
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 80% (non-condensing)
Maximum BTU 750 BTU / HR
DIMENSIONS Height Width Depth Weight
Unit 3.03 in
(7.7 cm)
12 in
(30.5 cm)
14.17 in
(36.0 cm)
10.6 lb
(4.81 kg)
Packaging with
contents
8.27 in
(21.0 cm)
15.55 in
(39.5 cm)
19.41 in
(49.3 cm)
15.1 lb
(6.85 kg)
Rack Space 2U
POWER
Input Power 100/240V AC (50/60 Hz) 2.7A
Maximum Power 225W
OPERATING PARAMETERS
Rated Power
(Speaker Output)
50 WPC at 8 ohms (THD+N < 0.1%)
70 WPC at 8 ohms (THD+N < 1.0%)
Frequency
Response
20 Hz – 20 kHz +/
-
0.5 dB, speaker output
Signal-to-Noise
Ratio (SNR)
>95 dB, speaker output
Supported Digital
Input Formats
44.1 kHz / 48 kHz / 96 kHz at 16-bit / 20-bit /
24-bit resolution
NETWORKING
Supported
Standard
IEEE 802.1 AVB/TSN switches
IEEE 802.3 Ethernet
REGULATORY
Safety & Emissions FCC Part 15B CE Mark C-Tick UL
RoHS Compliant
MINIMUM SUPPORTED REQUIREMENTS
Release Savant OS: da Vinci 8.2
Hardware Requires pairing with a Savant Smart Host or Pro Host.
MUSIC STREAMING
The Pro Audio 4 has a built-in single stream of Savant Music, which includes
popular music streaming services powered by Autonomic MirageOS.
(Streaming service fees may apply.)
RACK INSTALLATION
The Savant Pro Audio 4 device can be mounted in a 2U rack style enclosure
and is compatible with all standard 19-inch National Electrical Manufacturers
Association (NEMA) rack mounts. The 2U Rack Bracket needs to be attached
prior to mounting. See Pro Audio 4 Deployment Guide for more information.
C
D
E
F G
A
B
432
1
-
1 +- 2 +
WIRING AND CONNECTIONS
SPEAKER CONNECTIONS
Speaker wiring connections are made
using 4-pin Speaker Connectors
supplied with the device. The wire
slips into the hole and locks with a
screw located at the top of the
connector. Speaker connectors
accept up to 12AWG speaker cable.
NOTE: Wire order shown does not represent any wiring standard.
It may be dierent than other models.
NOTE: While not shown in the diagram above, Zones 2 to 4 follow
the same wiring as Zone 1.
RS-232 CONNECTIONS
Pins 7 and 8 are only required
for CTS/RTS handshaking.
IMPORTANT: When wiring to
this port, do not connect any
wires within the cable that are not
required for communication.
NOTE: CTS/RTS handshaking is supported for flow control based on
the profile used in the configuration.
NOTE: Wire coloring is included to identify the pins used for this connection.
Colors shown do not represent any wiring standard.
NOTE: The Pro Audio 4 does not support RS-422/485.
RJ-45 TO DB9 ADAPTERS: Savant oers RJ-45 to DB9 adapters in a variety
of configurations that can be used for RS-232 control.
Refer to the RS-232 Conversion to DB9 and Pinout Application Note located
on the Savant Community for more information on RJ-45 to DB9 adapters.
IR WIRING
IR connections are made using
4-pin IR Connectors supplied with the
device. The wire slips into the hole and
locks with a screw located at the top
of the connector.
IMPORTANT: IR Wiring Precautions
Ensure that all IR emitters are within 15 feet (4.6 meters) from the
controller’s location.
Use of 3rd party blinking IR emitters with Talk Back is not recommended.
These types of emitters can draw voltage away from the IR signal that
can degrade IR performance.
NOTE: While not shown in the diagram above, IR connections 3 and 4
follow the same wiring as 1 and 2.
REAR PANEL
FCC INTERFERENCE STATEMENT: PRO AUDIO 4
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interferences that may cause
undesired operation.
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for CLASS B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications, However there is no guarantee that interference
will not occur in a particular installation, If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try correct the interference by one or more of the
following measures:
–
Reorient or relocate the receiving circuit dierent from that to which receiver
is connected.
–
Increase the separation between the equipment and the receiver.
–
Consult the dealer or experienced radio/TV technician for help.
INDUSTRY CANADA STATEMENT: PRO AUDIO 4
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
For product
information:
Part # HDH6C001010 3B
© 2016 Savant Systems, LLC. 45 Perseverance Way, Hyannis, MA 02601
Telephone: 508 683 2500
Printed in China.
SMA-5000-00, 009-1411-01_00, 161003
savant.com
PIN 1 Right
-
PIN 2 Right +
PIN 3 Left
-
PIN 4 Left +
Use white stripe
for positive (+)
PIN 1 IR 1
-
PIN 2 IR 1 +
PIN 3 IR 2
-
PIN 4 IR 2 +
Use white stripe
for positive (+)
PIN 1 –
PIN 2 –
PIN 3 –
PIN 4 GND (RS-232)
PIN 5 RXD (RS-232)
PIN 6 TXD (RS-232)
PIN 7 CTS (RS-232)
PIN 8 RTS (RS-232)
RJ-45 CONNECTOR
(Gold pins facing up)
PIN 1 PIN 8
REGULATORY STATEMENTS
Speaker
Connections
(4) Speaker output zones
Uses 4-pin Speaker Connectors
NOTE: Compatible with 8 ohm or 4 ohm speakers.
Analog Preamp
Output
(1) Analog stereo line output (Left & Right)
Analog Inputs (2) Analog stereo inputs, RCA line-level inputs;
22 kΩ input impedance
Digital Audio
Out
(1) Digital optical preamp output (TOSLINK),
line-level 96kHz/24-bit output, fixed volume
Digital Audio In (2) Digital optical audio inputs (TOSLINK).
Supports up to 96kHz/24-bit digital audio in;
PCM stereo format only.
IR (4) IR Ports
Uses 4-pin IR Connectors to send IR signals to control
devices with an IR input or IR receiver via an IR flasher
(5V tolerant only). See IR Wiring section for important
precautions regarding IR functionality before making
any connections.
RS-232 8-pin RJ-45 port used to transmit and receive serial
binary data to and from serial controllable devices.
CTS/RTS handshaking availability based on
component profile. See RS-232 Connections section
for pin-outs.
Ethernet 8-pin RJ-45 port
10/100/1000 Base-T auto-negotiating port with Link/
Activity LEDs
Supports Audio Video Bridging (AVB)
Ethernet
Activity LED
Green Blinking: Activity (Rx/Tx)
O: No Activity
Ethernet Link
LED
Green Solid: Ethernet Link is established (any speed)
O: Ethernet link is not established
USB USB 2.0 Type A (reserved for future use)
Fuse 250V 3A slow blow fuse; field replaceable
See Pro Audio 4 Deployment Guide for additional
information on replacing the fuse.
Power Input 100/240V AC (50/60 Hz) 2.7A
I/O (power
switch)
I (On): Powers On the controller
O (O): Powers O the controller
EXPANSION
Up to three Pro Audio 4 units can be connected using AVB compliant
switching, providing up to 18 zones of distributed audio (12 amplified
zones and 6 preamp zones). See Pro Audio 4 Deployment Guide for
additional information.
NETWORK REQUIREMENTS
Connect all Savant devices to the same local area network (LAN) or subnet
as the host. Savant recommends not implementing any type of trac or
packet shaping in your network topology for the Savant devices as this may
interfere with performance.
NETWORK CONFIGURATION
To ensure that the IP Address will not change due to a power outage,
a static IP Address or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, static IP Addresses for all devices can be managed from a single
UI, avoiding the need to access devices individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Refer to the Pro Audio 4 Deployment Guide (009-1413-xx) located on the
Savant Community for more information.
C
D
H
K
L
M
N
I
J
F
G
A
B
E
B D
H
K
MF
C
L
NI JG
A
E
-
R +- L +
Zone 1
432
1
Loading...