Savant Netgear M4300 8x8F,Netgear M4300 24x24F,Netgear M4300 12x12F Configuration Manual

Download

45 Perseverance Way, Hyannis, MA 02601

Savant.com | 508.683.2500

Video over IP Network

Netgear M4300 8x8F | M4300 12x12F | M4300 24x24F

Configuration Guide

Document Number:

009-1552-00

Document Date:

November 2017

Document Supports:

da Vinci 8.7

Video over IP Network Configuration Guide

009-1552-00 | 171128

2 of 13

Contents

1! Overview ........................................................................................................................................................... 3!

2! Network Topology ........................................................................................................................................ 3!

3! Switch Configuration (Script) .................................................................................................................. 4!

4! Switch Configuration (Manual) ................................................................................................................ 5!

4.1! VLAN Setup ............................................................................................................................................................................. 5!

4.2! Multicast .................................................................................................................................................................................... 5!

4.3! Access Control List (ACL) Creation ............................................................................................................................... 8!

4.4! Save Configuration .............................................................................................................................................................. 10!

Appendix A: 10G Switch Requirements ..................................................................................................... 11!

Appendix B: Static IP ........................................................................................................................................ 12!

Video over IP Network Configuration Guide

009-1552-00 | 171128

3 of 13

1 Overview

This document provides the necessary features/capabilities that any 10G switch needs to have to work correctly with the Savant Video over IP System. It also provides information on how to enable these features for the 10G switches that Savant has qualified.

2 Network Topology

Savant recommends that the 10G Switch is connected to the same switch that the Host is connected to. Unmanaged switches should not be connected to the 10G Switch that the Video over IP system is using. The image below is a basic network diagram.

– 10G connections to the PAV-VIMxS devices use SFP+ ports either fiber or Direct Attach Copper cables can be

used.

– 10G connections to the PAV-VOMVP1x can use either SFP+ ports with fiber cabling or RJ-45 ports with CAT-6

or above cabling, depending on the cable length.

Video over IP Network Configuration Guide

009-1552-00 | 171128

4 of 13

3 Switch Configuration (Script)

This is the recommended method for configuring the Netgear ProSafe switches. These steps are to be done with the switch at its Factory default settings.

1. Download the Configuration scripts, use the Link below:

http://cdn.software.s3.amazonaws.com/scripts/Netgear/ConfigScripts.zip

2. Using Finder navigate to the download location.

3. Move the ConfigScript.zip to the Desktop of your SDE.

4. Double click on the ConfigScripts.zip to unzip the folder

5. Open the ConfigScripts folder

6. Move the Script for the switch that is in use to the Desktop.

7. Connect the upper left RJ-45 port on the Netgear switch to the main switch. Below see the port number based on the model in use. M4300-8X8F port 9 M4300-12X12F port 13 M4300-24X24F port 25

8. Use a network scanning software to find the IP address of the switch

9. Open Terminal on the SDE

10. Type: sh ~/Desktop/<NameOfScriptFile>.sh Example: sh ~/Desktop/M4300-24X24F-Config.sh

11. Enter the IP Address of the Netgear switch. Once enter is pressed the script will run and configure the switch.

Video over IP Network Configuration Guide

009-1552-00 | 171128

5 of 13

4 Switch Configuration (Manual)

This section gives the settings for the Savant qualified Netgear 10G ProSafe M4300 switches. Only the settings needed for the Audio Video over IP environment are described and no other setting are noted. These steps are to be done with the switch at its Factory default settings.

4.1 VLAN Setup

1. Connect to the Switch via a web browser.

2. Enter the User ID and Password: Default: admin Password: (leave, blank there is no password by default)

3. Go to Switching > VLAN

4. Add a VLAN.

5. Enter VLAN ID and VLAN Name. Below are Savant’s recommendations. VLAN ID: 1 VLAN Name: default

6. Click Apply in the upper right corner of the browser window.

4.2 Multicast

1. Go to Switching > Multicast.

2. Click on IGMP Snooping > Multicast Router Configuration.

Video over IP Network Configuration Guide

009-1552-00 | 171128

6 of 13

3. Click the Check box to select all

4. Select Disable in Multicast Router.

5. Click Apply in the upper right corner of the browser window.

6. Still inside Switching > Multicast, go to IGMP Snooping > Configuration.

7. Enable Admin Mode, Validate IGMP IP header, and Proxy Querier Mode.

8. Click Apply in the upper right corner of the browser window.

9. Still inside Switching > Multicast, go to IGMP Snooping > IGMP VLAN Configuration.

Video over IP Network Configuration Guide

009-1552-00 | 171128

7 of 13

10. Adjust to the setting in the table below.

Category

Value

Sequence Number

Action

Permit

Match Every

True

10. Select Apply.

11. Click Advanced > IP Binding Configuration.

12. Select ACL ID 101

13. Change the Direction to outbound

14. Click the port that this rule is to be applied. Below is a list by model of the Savant recommended port. M4300-8X8F port 9 M4300-12X12F port 13 M4300-24X24F port 25

15. Select Apply in the top right corner.

4.4 Save Configuration

1. Go to Maintenance > Save Config.

2. Click Save Configuration

3. Click the Check-box

4. Click Apply in the upper right corner of the browser window.

Video over IP Network Configuration Guide

009-1552-00 | 171128

11 of 13

Appendix A: 10G Switch Requirements

The following list is the settings that need to be configured on any Switch that is being used for the Audio/Video over IP system.

IMPORTANT!

Not all of these settings are on all network switches. – 10G Managed Switch with SFP+ ports – IGMP Snooping Enabled. – Enable IGMP Snooping on all ports for the VLAN in use. – IGMP Querier Enabled. – Enable IGMP Querier on all ports for the VLAN in use. – Filter/Drop Unregistered Multicast Traffic Enabled. – Unregistered Multicast Flooding Disabled. – FASTLEAVE enabled (Optional*). – Enable FASTLEAVE on all ports for the VLAN in use (Optional*). * FASTLEAVE will make changing services faster.

Video over IP Network Configuration Guide

009-1552-00 | 171128

12 of 13

Appendix B: Static IP

If the switch needs to have a Static IP Address set it needs to be done before the rest of the configuration is done. To set a Static IP Address for the Netgear M4300 switches follow the steps below.

1. Turn off your SDE’s Wi-Fi

2. The Netgear M4300 switch should have no connections other than its power connecition.

3. Directly connect an SDE to the upper left RJ-45 network port on the Netgear M4300.

4. Open a Web browser.

5. In the Address Bar enter 169.254.100.100.

NOTE: This is the default self-assigned network address.

6. Enter the User ID:

Default: admin

7. There is no Password by default (leave blank).

8. Go to Switching > VLAN

9. Add a VLAN.

10. Enter VLAN ID and VLAN Name. Below are Savants recommendations.

VLAN ID: 1 VLAN Name: default

11. Select Manual under Configuration Method.

12. Enter the IP Address, Subnet Mask, and Gateway for the switch.

NOTE: Make sure that the IP Address entered is inside the network IP scheme of the router.

13. Click Apply in the upper right corner of the browser window.

Video over IP Network Configuration Guide

009-1552-00 | 171128

13 of 13

Important Notice

Disclaimer

Savant Systems, LLC. reserves the right to change product specifications without notice, therefore, the information presented herein shall not be construed as a commitment or warranty.

Savant Systems, LLC. shall not be liable for any technical or editorial errors or omissions contained herein or for incidental or consequential damages resulting from the performance, furnishing, reliance on, or use of this material.

Patents

Certain equipment and software described in this document is protected by issued and pending U.S. and foreign patents.

All products and services are trademarks or registered trademarks of their respective manufacturer.

This document contains confidential and proprietary information protected by copyright. All rights reserved. Copying or other reproduction of all or parts of this document is prohibited without the permission of Savant Systems.

Trademarks

© 2017 Savant Systems, LLC. All rights reserved. Savant, Savant App, Savant Host, Now You Can, RacePoint Blueprint, Single App Home, TrueCommand, TrueControl, and the Savant logo are trademarks of Savant Systems, LLC.

AirPlay, Apple, AirPort Express, AirPort Extreme, Apple TV, Apple Remote Desktop, FireWire, iMac, iTunes, iPad, iPad mini, iPad Air, iPhone, MacBook, Mac and OS X are trademarks or trade names of Apple Inc. iOS is a trademark of Cisco®. Android, Google, Google Play, and other Google marks are trademarks of Google, Inc. Wi-Fi is a registered trademark of the Wi-Fi Alliance®. HDMI® is a trademark of HDMI Licensing, LLC. Autonomic® and TuneBridge® are registered trademarks of Autonomic Controls, Inc. MOTU® is a registered trademark of Mark of the Unicorn, Inc. Luxul® is a registered trademark of Luxul Wireless. NETGEAR, the NETGEAR Logo, and ProSAFE are trademarks of NETGEAR, Inc.

All other brand names, product names, and trademarks are the property of their respective owners.

Technical and Sales Support

Savant Systems, LLC is dedicated to providing prompt and effective support in a timely and efficient manner.

– To contact Savant Support, access the Savant Customer Community and create a support case. – To contact Savant Sales, visit Savant.com and select Contact Us to locate a local sales representative in

your area.

Savant Netgear M4300 8x8F,Netgear M4300 24x24F,Netgear M4300 12x12F Configuration Manual

Specifications and Main Features

Frequently Asked Questions

User Manual