Saturday Knight LTD. 1040, 1030 User Manual

ABBREVIATIONS

Assy ..........................................Assembly

A/R ............................................ As Required

B ................................................ Bolt

Brg ............................................. Bearing

BSN ...........................................Before Serial Number

Btm ............................................ Bottom

C-Bolt ........................................Carriage Bolt

Cttr............................................. Cotter

CV ............................................. Constant Velocity

Deg ............................................Degree

Dia .............................................Diameter

ea .............................................. Each

eq or Equiv .................................Equivalent

Fln .............................................Flanged Lock Nut

Fw..............................................Flat Washer

Ga.............................................. Gauge

Gr or Grd .................................... Grade

Hd ..............................................Head

Hyd ............................................Hydraulic

ID ...............................................Inside Diameter

Ill or Illus ....................................Illustration

Ind..............................................Indicator

Kw ............................................. Keyway

LH ..............................................Left Hand

Ln .............................................. Lock Nut

Lw .............................................. Lock Washer

Mtg Hrd ...................................... Mounting Hardware

NC ............................................. National Coarse

NF.............................................. National Fine

NPT ........................................... National Pipe Thread

OD .............................................Outside Diameter

Pc(s) ..........................................Piece(s)

PD ............................................. Pitch Diameter

PTO ...........................................Power Takeoff (shaft)

Q or Qty ..................................... Quantity

Reg Mach ..................................Regular Machine

RH .............................................Right Hand

SN ............................................. Serial Number

Spk, or Spkt or Sprkt ................. Sprocket

Sq ..............................................Square

SS ............................................. Stainless Steel

SSB ...........................................Stainless Steel Bolt

St ............................................... Straight

Std ............................................. Standard

STS ........................................... Self Tapping Screw

UASN ........................................ Used After Serial Number

UBSN ........................................Used Before Serial Number

W...............................................With

W/O ........................................... With Out

USING THIS SERVICE PARTS LISTING

This listing uses a number indentation system to specify the parts of an assembly.Any number which is indented to the right, indicates that it is a component of the item to the upper left. Example:

Part no Qty Description 102-AAA # Assembly A

102-BBB # Sub-Assembly B (Component of A)

140-xxx # Sub-Component of B

140-xxx # Sub-Component of B 102-CCC # Sub-Assembly C (Component of A) etc.

Using this system, the subassemblies and their components are included if an Assembly is ordered. Similarly, the components of a subassemblies are included if a subassembly is ordered.

The quantity (Qty) associated with an assembly, represents the number of times an assembly shown in the drawing. The subassembly quantity however, is the number of times a subassembly is used to build one assembly. Similarly, the component quantity refers to the number of times a given component is found in one subassembly.

could be

MODEL AND SERIAL NUMBER INFORMATION is located near the front left hand corner (Fig. A). The model number, serial number and part number should be known when asking service personnel for parts.

If you cannot find the part you need, be as descriptive as possible when placing an order:

Sprockets: give the bore size, number of teeth,

and size of keyway.

Roller chain: give the size of chain (stamped on

the side of each link) and number of links.

Shafting: give the diameter, length, and quantity

and size of keyways.

Hardware is generally not included with parts.If you need any hardware, check the size, the length, and the grade (Fig. B), then check the hardware list in this manual for the part numbers.

All hex head bolts are grade 5, and nuts are grade B unless otherwise stated.

The hardware listing also includes listings for zerks, cotter pins, set screws, and roller chain links.

The illustrations in this manual are meant to be used only as a guide for identifying parts and locating their relative positions.

BOLT GRADES

KNIGHT MANUFACTURING CORP.

1501 West 7th Ave. Brodhead, WI 53520-0167

701 Cherry Ave. Greeley, Co. 80632